Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
0145189-HVAC (RTU's/curbs/DDC Control/ceiling fans)
WINNEBAGO COUNTY, WISCONSIN FACILITIES & PROPERTY MANAGEMENT REQUEST FOR SEALED BIDS FOR HVAC REPLACEMENT AT SUNNYVIEW EXPOSITION CENTER RFB# MA09 -10 TABLE OF CONTENTS HVAC REPLACEMENT AT SUNNYVIEW EXPOSITION CENTER RFB# MA09 -10 DESCRIPTION PAGE Invitationto Bid ...................................................................... ............................... 1 -3 BidForm .............................................................................................. .............................. Contractor's Qualification Statement ................................................... ............................5 -7 Insurance Requirements- Exhibit A ...................................................... ............................... 8 Owner Direct Purchases - Exhibit B ...................................................... ............................... 9 Special Provisions Related To ARRA- Exhibit C ............................... ..........................10 -18 Federal Davis Bacon Wage Rates ...................................................... ..........................19 -25 State of Wisconsin Prevailing Wage Rates ........................................ ..........................26 -36 TECHNICAL SPECIFICATIONS # OF PAGES Section 23 05 00 Common Work Results for HVAC ................ ..............................7 Section 23 05 13 Motors and Electrical Work ........................... ..............................4 Section 23 05 17 Pipe, Tube, & Fittings for HVAC Systems ... ............................... 4 Section 23 05 19 Piping Specialties for HVAC Systems .......... ............................... 3 Section 23 05 29 Hangers & Supports for HVAC Systems ...... ............................... 4 Section 23 05 93 Testing, Adjusting, & Balancing .................. ............................... 3 Section 23 07 00 Insulation for HVAC Systems ....................... ..............................3 Section 23 09 23 Direct Digital Control for HVAC Systems ... ............................... 9 Section 23 1100 Facility Fuel Piping ........................................ ..............................4 Section 23 3100 HVAC Ductwork and Casings ....................... ..............................6 Section 23 33 00 Air Duct Accessories .................................... ............................... 5 Section23 34 00 HVAC Fans .................................................... ..............................2 Section 23 74 00 Packaged Outdoor HVAC Equipment .......... ............................... 6 Section 26 05 00 Common Work Results for Electrical ........... ............................... 2 Section 26 05 01 Electrical Scope of Work .............................. ............................... l Section 26 05 19 Low Volt Power Conductors & Cables .......... ..............................4 Section 26 05 26 Grounding and Bonding ................................ ............................... 3 Section 26 05 29 Supporting Devices ........................................ ..............................3 Section 26 05 33 Raceway and Boxes ...................................... ............................... 5 DRAWINGS (In separate PDF file titled "Drawings") See Title Sheet for List of Drawings- All to be Printed on 24" x 32" Sheets ...................11 INVITATION TO BID Winnebago County is requesting sealed bids for HVAC Replacement at Sunnyview Expo Center. This is Winnebago County's Request for Bid (RFB) # MA09 -10. Pre -Bid Meetings & Requirements Bidders are responsible for familiarizing themselves with the site and project specifications before submitting a bid. A Winnebago County's Contractors Qualification Statement must be completed and received with the bid. A blank Qualification Statement is included in this bid packet. The Qualification Statement must demonstrate the Contractor's ability to perform the work to the County's satisfaction. The County reserves the right to contact references and/or make additional inquiries as deemed necessary to establish the Contractor's qualifications. A pre -bid meeting will be held at 9:00 AM, local time, on September 30, 2010 to view existing conditions and review project requirements. Interested contractors should meet at the front entrance to the Expo Center at 500 E. County Road Y, Oshkosh, WI. If the Bidder receives a Bid packet from any source or entity other than the Onvia /Demandstar website, the Bidder is responsible for calling Winnebago County Purchasing Department and requesting the Bidder's name be placed on the County's formal bidders list for the project. Failure of the Bidder to notify the Purchasing Department in no way obligates the County to mail addendum or other information concerning the Bid to the Bidder. Bidding Requirements All prices are to be net F.O.B.- Destination, Sunnyview Expo Center, 500 E. County Rd. Y, Oshkosh, WI. A certified check, cashier's check, or bid bond payable to Winnebago County in an amount of five percent (5 %) of the bid amount must accompany the bid as a guarantee that if the bid is accepted, the bidder will execute and file the proper contract within ten (10) days after award of the contract. Contractor shall furnish a Public Improvement Performance /Labor and Material Payment Bond pursuant to Sec. 779.14 WI Statutes, with a surety duly authorized to and licensed to do business in the State of Wisconsin for use and benefit of claimants in an amount not less than the contract sum. Winnebago County is a tax - exempt municipal corporation, under Wisconsin Statute 77.54 (9a). All bidders must follow the instructions in Exhibit B regarding Owner Direct Purchase of Materials for the project. This project is funded in part by ARRA /EECBG (American Recovery and Reinvestment Act/ Energy Efficiency and Conservation Block Grant) and as such, is subject to the Buy American requirements and other special provisions related to funding under the Act. See Exhibit C for special provisions related to ARRA. The EERE has recently issued guidance to provide assistance in determining where a product is manufactured. These documents are available on the EERE Buy American Website at htt :/ /www /recovery /buy american This project is subject to the provisions of the Davis Bacon Act which requires that federal wage rates be paid on the project. The federal wage rates applicable to this project are included in this bid packet and an explanation is provided as part of Exhibit C. This project is subject to Section 66.293, WI State Statutes, which requires all contractors and sub- contractors to comply with the Prevailing Wage Rates applicable to this project. Prevailing Wage Rates are included in this bid packet. Contractor must pay the wage rate that is the higher of two, federal or state for each trade. Contractor is required to file monthly certified payroll reports with the Wisconsin Dept. of Workforce Development. Go to http: / /www.dwd.state.wi.us /er /prevailing wage rate/Website- Certified %20Payrolls - Draft3- 0128I O.htm for more information. The successful Contractor will be required to sign a contract (Winnebago County Purchase of Services Agreement) within 10 days after award. A sample contract is available from the Purchasing department upon request. Call (920) 236 -4875 or email ebuchholz@co.winnebago.wi.us to request a sample. Insurance Requirements Successful bidder must provide a Certificate of Insurance meeting County requirements as stated in Exhibit A. Bid Submission Bids must be filed in the office of the Winnebago County Clerk, no later than 2:00 p.m., central time, October 12, 2010. Bids received after the above hour and date, will be returned unopened to the bidder. Hand deliver bids to: Winnebago County Courthouse, Room 110, 415 Jackson Street, Oshkosh, WI 54901 or Mail to: Winnebago County Clerk's Office, PO Box 2808, Oshkosh, WI 54903 -2808. All bids must be submitted in complete original form along with one (1) additional copy. An authorized individual using an unduplicated original signature is required to sign the bid for the bidder on the Signature Page. The bids must be sealed and must be plainly marked in the lower left -hand corner of the envelope "RFB# MA09 -10 ". Failure to properly mark the envelope may eliminate bid. All questions on the bid forms must be answered by the bidder. All additional information required must be attached to the back of the bid packet. Any other information not specifically solicited but pertinent to the vendor's proposal may also be attached to the back of the entire packet. Any deviations from the enclosed specifications must be noted on the Bid Form. Deviations from the specification can be cause for bid rejection. Deviations will be evaluated on an individual basis. Written requests for withdrawal of bids is permitted any time prior to the public opening of bids. Winnebago County reserves the right to award this bid in its entirety or award by individual item or division of work whichever is most advantageous to the County. All bids submitted shall be binding for sixty (60) calendar days following the bid opening date, unless the bidder(s), upon request of the County, agree to the extension. Bid Opening Bids will be opened and publicly read at 2:05 p.m., central time, October 12, 2010 in the Courthouse Lounge, Room 60, Winnebago County Courthouse, 415 Jackson Street, Oshkosh, WI. Award, if any, will be made as soon as possible thereafter. Other Information Winnebago County is not liable for any costs incurred in replying to this Request for Bids. The County reserves the right to reject any and all bids, to select the bid considered most advantageous to Winnebago County and to waive any informalities in bidding. Award of this project may be contingent upon the County Board and/or County Executive's approval of funding for the project. Any bids submitted in conjunction with this request will become a public record, open for public inspection. If there is confidential or propriety information which should be exempted from this requirement, bidders must include a separate request explaining what items should be exempted and why. Notification of the County's determination on such requests will be made prior to release of any information in the bid. Winnebago County reserves the right to cancel any order or contract for failure of the successful bidder to comply with the terms, conditions and specifications of this request and/or contract. Successful bidder shall comply with all applicable local codes and shall obtain all necessary permits. Vendors will be required to comply with Winnebago County Resolution #251 -693, which requires all departments, commissions, contractors, sub - contractors and boards of Winnebago County to utilize the Winnebago County Solid Waste facilities for solid waste disposal. Vendor shall be aware that, upon request, scale tickets must be provided. Should any party protest the procedure pursuant to which Winnebago County has awarded bids or contracts with regard to this project, that party shall file a written protest, describing the nature of thereof, with the Winnebago County Purchasing Agent within five (5) business days of the date of the notice of said award. The Purchasing Agent shall review the protest and issue a written decision as to the protest within seven (7) days of receipt of the protest. Any party may then request, by letter, review of the decision of the Purchasing Agent within five (5) business days of the date of that decision by the Winnebago County Executive. The County Executive shall review the Purchasing Agent's decision and shall issue a written decision either upholding, reversing, or modifying the Purchasing Agent's decision within seven (7) days of the date of receipt of said letter by the County Executive. Contacts Requests for further information concerning this request for bid must be directed to: Winnebago County Purchasing Department 448 Algoma Blvd. Room 322, PO Box 2808 Oshkosh, WI 54903 -2808 Phone: (920) 236 -4875, Fax: (920) 236 -4799 Email: cbuchholz(a�, All questions about the meaning or intent of the Bid Documents shall be submitted to the Purchasing Department in writing. Replies shall be issued by Addenda, mailed or delivered to all parties recorded as having received the Bid documents. Questions received less than five (5) days prior to the date for opening of bids will not be answered. Only questions answered by formal written addenda will be binding. Oral and other interpretations or clarifications will be without legal effect. BID FORM RFB# MA09 -10 The undersigned has carefully examined the Specifications and all other Documents relating to the project and acquainted himself /herself with the site and all other conditions relevant to the work. A) The undersigned hereby proposes and agrees to furnish all labor, materials (except those included in item B below), equipment, tools, taxes, services and all other things necessary or appropriate for the proper and complete execution of the work for the Lump Sum of: B) Owner Direct Purchase Materials (do not include sales tax in this amount): C) Total (Add lines A & B): $ List any deviations from the specifications below (attach separate sheet if necessary): In submitting this Bid, the Bidder represents, that the Bidder has examined and carefully studied the following addenda, the receipt of which is hereby acknowledged: Addendum Number Date Bidder: Address: Phone Number: Email: Signature: Printed Name: Title Date: Fax Number: 11 WINNEBAGO COUNTY CONTRACTOR'S QUALIFICATION STATEMENT SUBMITTED BY: NAME: RE: RFB# MA09 -10 HVAC REPLACEMENT CORPORATION ( ) PARTNERSHIP( ) INDIVIDUAL ( ) JOINT VENTURE( ) OTHER ( ) 1) TYPE OF WORK (explain each type of work performed by your organization) 2) ORGANIZATION A. How many years has your organization been in business? B. How many years has your organization been in business under its present business name? C. Under what other or former names has your organization operated? D. If your organization is a corporation, answer the following: 1. Date of incorporation: 2. State of incorporation: 3. President's name: 4. Vice - president's name: 5. Secretary's name: 6. Treasurer's name: E. If your organization is a partnership, answer the following: 1. Date of organization: 2. Type of partnership (if applicable): 3. Name(s) of general partner(s): 5 F. If your organization is individually owned, answer the following: 1. Date of organization: 2. Name of owner: G. If the form of your organization is other than those listed above, describe it and name principals: 3) LICENSING A. List jurisdictions and trade categories in which your organization is legally qualified to do business. B. List jurisdictions in which your organization's partnership or trade name is filed. 4) EXPERIENCE A. List the categories of work that your organization normally performs with its own forces and state for how many years your organization has been involved in each. B. Claims and Suits. (If the answer to any of the questions below is yes, please attach details.) 1. Has your organization ever failed to complete any work awarded to it? 2. Are there any judgments, claims, arbitration proceedings or suits pending or outstanding against your organization or its officers? 3. Has your organization filed any lawsuits or requested arbitration with regard to any related contracts within the last five years? C. Within the last five years, has any officer or principal of your organization ever been an officer or principal of another organization when it failed to complete a contract? (If the answer is yes, please attach details.) D. List any projects your organization has completed for Winnebago County in the past 10 years. Include the name of the County department and contact on the project: E. On a separate sheet, list major projects of similar nature that your organization has in progress, giving the name of the project, owner, contract amount, percent complete, and scheduled completion date. ■ State total worth of work in progress and under contract. F. On a separate sheet, list the major projects of similar nature your organization has completed in the past five years, giving the name of the project, owner, contract amount, date of completion, and percentage of the work performed with your own forces. ■ State the average annual amount of work performed during the past five years. G. On a separate sheet, list the construction experience and present commitments of the key individuals in your organization. 5) REFERENCES A. Trade References: B. Bank References: C. Surety: 1. Name of bonding company: 2. Name and address of agent: 3. 6) FINANCING Financial Statement must be provided upon request. 7) SIGNATURE Dated this day of 1 2010. Name of Organization: li Printed Name: Title: 7 EXHIBIT A INSURANCE COVERAGE' DESCRIPTIONS AND REQUIREMENTS I. Contractor shall, furnish County with Certificate of Insurance indicating proof of the following insurance from companies licensed in the State: A. Workers Compensation and Employers' Liability - Workers' Compensation statutory - in compliance with the Compensation law of the State and Employers' Liability insurance with a limit no less than $100,000 each accident. B. Comprehensive or Commercial General Liability with a minimum limit of $1,000,000 per occurrence /$1,000,000 aggregate combined Single Limit for Bodily Injury and Property Damage Liability. This insurance shall include, but not limited to, the following coverage. 1. Premises - Operations 2. Products and Completed Operations 3. Broad Form Property Damage 4. Contractual 5. Personal Injury If excavating, underground or collapse is involved the limits of liability state above shall be changed to $2,000,000. If Asbestos is involved the limits of liability stated above shall be changed to $5,000,000. C. Automobile Liability with a minimum limit of $1,000,000 per occurrence /$1,000,000 aggregate Combined Single Limit for Bodily Injury and Property Damage Liability. This insurance shall include coverage for all of the following: 1. Owned Automobiles 2. Hired Automobiles 3. Non -Owned Automobiles II. The certificate shall list the Certificate Holder and Address as follows: Winnebago County, Attn: Insurance Administrator, Winnebago County Courthouse, P.O. Box 2808, Oshkosh, WI 54903 -2808. The Winnebago County Department(s) involved shall be listed under "Description of Operations ". III. Such insurance shall include under the General Liability and Automobile Liability policies Winnebago County, its employees, elected officials, representatives, and members of its boards and/or commissions as "Additional Insureds ". IV. Such insurance shall include a thirty- (30) day notice to the County prior to cancellation or material policy change. The notice shall be given to the Winnebago County Insurance Administrator, c/o Winnebago County Courthouse, PO Box 2808, Oshkosh, WI 54903 -2808. NOTE: Standard Cancellation Clause on a Certificate of Insurance is not acceptable. V. Contractor shall require subcontractor; if applicable, to furnish identical certificates of insurance to the Winnebago County Insurance Administrator prior to contract taking effect. EXHIBIT B OWNER DIRECT PURCHASED MATERIALS Contractor shall follow these procedures for OWNER direct purchased materials for bid submission and work performance. 1. As a tax exempt body, Winnebago County intends to purchase materials directly from the manufacturer / supplier whenever such purchases exceed $9,999 in cost for a single manufacturer / supplier. For example, if the Bidder requires a widget costing $10, 000 from company ABC to complete the Work, this widget would be purchased directly f - om company ABC by the County to avoid sales tax. On the other hand, if S different kinds of widgets at a cost of $2, 000 /each are to be supplied by S different suppliers, the Bidder would order the widgets and include the cost in their base bid including sales tax. 2. Bidders are to list on their Bid Form in the area provided, the cost of the above items, without sales tax. Sales tax or other tax liabilities of all other materials are to be included in the bidder's base bid. 3. Winnebago County shall cause all materials and equipment directly purchased to be delivered to the successful contractor, who shall order, accept delivery and unload the materials. When the materials are delivered to the jobsite, the contractor shall promptly inspect them and bring to the attention of Winnebago County, any defects therein. 4. Contractor shall have the same responsibility for installation of materials as he would have if he purchased those materials and equipment, except as specifically amended by this exhibit. 5. Upon notification by letter of the Owner's letter of Intent, the apparent lowest successful bidder will be required to submit a break down for the Owner purchased material suppliers within 48 hours. 6. Bidders shall, during the bidding process, solicit from suppliers and manufacturers competitive bids for real property as listed above for Owner - Purchased items. 7. Materials and equipment shall be in compliance with the technical sections of the specifications. 8. Bidders shall identify the dollar value of the Owner - Purchased real property on the cost line of the bid form. This amount shall NOT be incorporated into the base bid amount. 9. All suppliers shall be bound to their respective technical specification sections. 10. The Contractor's Performance and Payment Bond shall be in the amount equal to 100% of the contract sum and NOT include the cost of Owner - Purchased items. 11. Owner will purchase, at a maximum, only the amount of material represented by the figure provided by the successful bidder. Underestimated materials shall be purchased and paid for by the respective Contractor. 12. The Owner shall not take, nor accept liability for quantity, time of delivery, shipping, receiving, handling, protection, insuring thereof, etc., of materials ordered and / or contracted or handled in this process. 13. The Contractor shall have the same responsibilities for installation of materials and equipment provided by the Owner, as he would have if purchased by the Contractor. EXHIBIT C SPECIAL REQUIREMENTS FOR ARRA FUNDING REQUIRED USE OF AMERICAN IRON, STEEL, AND MANUFACTURED GOODS -- SECTION 1605 OF THE AMERICAN RECOVERY AND REINVESTMENT ACT OF 2009 (a) Definitions. As used in this award term and condition- - (1) Manufactured good means a good brought to the construction site for incorporation into the building or work that has been -- (i) Processed into a specific form and shape; or (ii) Combined with other raw material to create a material that has different properties than the properties of the individual raw materials. (2) Public building and public work means a public building of, and a public work of, a governmental entity (the United States; the District of Columbia; commonwealths, territories, and minor outlying islands of the United States; State and local governments; and multi - State, regional, or interstate entities which have governmental functions). These buildings and works may include, without limitation, bridges, dams, plants, highways, parkways, streets, subways, tunnels, sewers, mains, power lines, pumping stations, heavy generators, railways, airports, terminals, docks, piers, wharves, ways, lighthouses, buoys, jetties, breakwaters, levees, and canals, and the construction, alteration, maintenance, or repair of such buildings and works. (3) Steel means an alloy that includes at least 50 percent iron, between .02 and 2 percent carbon, and may include other elements. (b) Domestic preference. (1) This award term and condition implements Section 1605 of the American Recovery and Reinvestment Act of 2009 (Recovery Act) (Pub. L. 111 - -5), by requiring that all iron, steel, and manufactured goods used in the project are produced in the United States except as provided in paragraph (b)(3) and (b)(4) of this section and condition. (2) This requirement does not apply to the material listed by the Federal Government as follows: (3) The award official may add other iron, steel, and/or manufactured goods to the list in paragraph (b)(2) of this section and condition if the Federal Government determines that -- (i) The cost of the domestic iron, steel, and/or manufactured goods would be unreasonable. The cost of domestic iron, steel, or manufactured goods used in the project is unreasonable when the cumulative cost of such material will increase the cost of the overall project by more than 25 percent; (ii) The iron, steel, and/or manufactured good is not produced, or manufactured in the United States in sufficient and reasonably available quantities and of a satisfactory quality; or (iii) The application of the restriction of section 1605 of the Recovery Act would be inconsistent with the public interest. (c) Request for determination of inapplicability of Section 1605 of the Recovery Act. (1)(i) Any recipient request to use foreign iron, steel, and /or manufactured goods in accordance with paragraph (b)(3) of this section shall include adequate information for Federal Government evaluation of the request, including -- (A) A description of the foreign and domestic iron, steel, and /or manufactured goods; (B) Unit of measure; (C) Quantity; (D) Cost; 10 (E) Time of delivery or availability; (F) Location of the project; (G) Name and address of the proposed supplier; and (H) A detailed justification of the reason for use of foreign iron, steel, and /or manufactured goods cited in accordance with paragraph (b)(3) of this section. (ii) A request based on unreasonable cost shall include a reasonable survey of the market and a completed cost comparison table in the format in paragraph (d) of this section. (iii) The cost of iron, steel, and /or manufactured goods material shall include all delivery costs to the construction site and any applicable duty. (iv) Any recipient request for a determination submitted after Recovery Act funds have been obligated for a project for construction, alteration, maintenance, or repair shall explain why the recipient could not reasonably foresee the need for such determination and could not have requested the determination before the funds were obligated. If the recipient does not submit a satisfactory explanation, the award official need not make a determination. (2) If the Federal Government determines after funds have been obligated for a project for construction, alteration, maintenance, or repair that an exception to section 1605 of the Recovery Act applies, the award official will amend the award to allow use of the foreign iron, steel, and /or relevant manufactured goods. When the basis for the exception is non - availability or public interest, the amended award shall reflect adjustment of the award amount, redistribution of budgeted funds, and /or other actions taken to cover costs associated with acquiring or using the foreign iron, steel, and /or relevant manufactured goods. When the basis for the exception is the unreasonable cost of the domestic iron, steel, or manufactured goods, the award official shall adjust the award amount or redistribute budgeted funds by at least the differential established in 2 CFR 176.110(a). (3) Unless the Federal Government determines that an exception to section 1605 of the Recovery Act applies, use of foreign iron, steel, and/or manufactured goods is noncompliant with section 1605 of the American Recovery and Reinvestment Act. (d) Data. To permit evaluation of requests under paragraph (b) of this section based on unreasonable cost, the Recipient shall include the following information and any applicable supporting data based on the survey of suppliers: Foreign and Domestic Items Cost Comparison Description Unit of measure Quantity Cost (dollars)* Item 1: Foreign steel, iron, or manufactured good Domestic steel, iron, or manufactured good Item 2: Foreign steel, iron, or manufactured good Domestic steel, iron, or manufactured good [List name, address, telephone number, email address, and contact for suppliers surveyed. Attach copy of response; if oral, attach summary.] [Include other applicable supporting information.] [ *Include all delivery costs to the construction site.] DAVIS BACON ACT REQUIREMENTS Note: Where necessary to make the context of these articles applicable to this award, the term "Contractor" shall mean "Recipient" and the term "Subcontractor" shall mean "Subrecipient or Subcontractor" per the following definitions. Recipient means the organization, individual, or other entity that receives an award from DOE and is 11 financially accountable for the use of any DOE funds or property provided for the performance of the project, and is legally responsible for carrying out the terms and conditions of the award. Subrecipient means the legal entity to which a subaward is made and which is accountable to the recipient for the use of the funds provided. The term may include foreign or international organizations (such as agencies of the United Nations). Davis -Bacon Act (a) Definition. -- "Site of the work " -- (1) Means- - (i) The primary site of the work. The physical place or places where the construction called for in the award will remain when work on it is completed; and (ii) The secondary site of the work, if any. Any other site where a significant portion of the building or work is constructed, provided that such site is -- (A) Located in the United States; and (B) Established specifically for the performance of the award or project; (2) Except as provided in paragraph (3) of this definition, includes any fabrication plants, mobile factories, batch plants, borrow pits, job headquarters, tool yards, etc., provided- - (i) They are dedicated exclusively, or nearly so, to performance of the award or project; and (ii) They are adjacent or virtually adjacent to the "primary site of the work" as defined in paragraph (a)(1)(i), or the "secondary site of the work" as defined in paragraph (a)(1)(ii) of this definition; (3) Does not include permanent home offices, branch plant establishments, fabrication plants, or tool yards of a Contractor or subcontractor whose locations and continuance in operation are determined wholly without regard to a particular Federal award or project. In addition, fabrication plants, batch plants, borrow pits, job headquarters, yards, etc., of a commercial or material supplier which are established by a supplier of materials for the project before opening of bids and not on the Project site, are not included in the "site of the work." Such permanent, previously established facilities are not a part of the "site of the work" even if the operations for a period of time may be dedicated exclusively or nearly so, to the performance of a award. (b) (1) All laborers and mechanics employed or working upon the site of the work will be paid unconditionally and not less often than once a week, and without subsequent deduction or rebate on any account (except such payroll deductions as are permitted by regulations issued by the Secretary of Labor under the Copeland Act (29 CFR Part 3)), the full amount of wages and bona fide fringe benefits (or cash equivalents thereof) due at time of payment computed at rates not less than those contained in the wage determination of the Secretary of Labor which is attached hereto and made a part hereof, or as may be incorporated for a secondary site of the work, regardless of any contractual relationship which may be alleged to exist between the Contractor and such laborers and mechanics. Any wage determination incorporated for a secondary site of the work shall be effective from the first day on which work under the award was performed at that site and shall be incorporated without any adjustment in award price or estimated cost. Laborers employed by the construction Contractor or construction subcontractor that are transporting portions of the building or work between the secondary site of the work and the primary site of the work shall be paid in accordance with the wage determination applicable to the primary site of the work. (2) Contributions made or costs reasonably anticipated for bona fide fringe benefits under section 1(b)(2) of the Davis -Bacon Act on behalf of laborers or mechanics are considered wages paid to such laborers or mechanics, subject to the provisions of paragraph (e) of this article; also, regular contributions made or costs incurred for more than a weekly period (but not less often than quarterly) under plans, funds, or programs which cover the particular weekly period, are deemed to be constructively made or incurred 12 during such period. (3) Such laborers and mechanics shall be paid not less than the appropriate wage rate and fringe benefits in the wage determination for the classification of work actually performed, without regard to skill, except as provided in the article entitled Apprentices and Trainees. Laborers or mechanics performing work in more than one classification may be compensated at the rate specified for each classification for the time actually worked therein; provided, that the employer's payroll records accurately set forth the time spent in each classification in which work is performed. (4) The wage determination (including any additional classifications and wage rates conformed under paragraph (c) of this article) and the Davis -Bacon poster (WH -1321) shall be posted at all times by the Contractor and its subcontractors at the site of the work in a prominent and accessible place where it can be easily seen by the workers. (c) (1) The Contracting Officer shall require that any class of laborers or mechanics which is not listed in the wage determination and which is to be employed under the award shall be classified in conformance with the wage determination. The Contracting Officer shall approve an additional classification and wage rate and fringe benefits therefore only when all the following criteria have been met: (i) The work to be performed by the classification requested is not performed by a classification in the wage determination. (ii) The classification is utilized in the area by the construction industry. (iii) The proposed wage rate, including any bona fide fringe benefits, bears a reasonable relationship to the wage rates contained in the wage determination. (2) If the Contractor and the laborers and mechanics to be employed in the classification (if known), or their representatives and the Contracting Officer agree on the classification and wage rate (including the amount designated for fringe benefits, where appropriate), a report of the action taken shall be sent by the Contracting Officer to the Administrator of the: Wage and Hour Division Employment Standards Administration U.S. Department of Labor Washington, DC 20210 The Administrator or an authorized representative will approve, modify, or disapprove every additional classification action within 30 days of receipt and so advise the Contracting Officer or will notify the Contracting Officer within the 30 -day period that additional time is necessary. (3) In the event the Contractor, the laborers or mechanics to be employed in the classification, or their representatives, and the Contracting Officer do not agree on the proposed classification and wage rate (including the amount designated for fringe benefits, where appropriate), the Contracting Officer shall refer the questions, including the views of all interested parties and the recommendation of the Contracting Officer, to the Administrator of the Wage and Hour Division for determination. The Administrator, or an authorized representative, will issue a determination within 30 days of receipt and so advise the Contracting Officer or will notify the Contracting Officer within the 30 -day period that additional time is necessary. (4) The wage rate (including fringe benefits, where appropriate) determined pursuant to subparagraphs (c)(2) and (c)(3) of this article shall be paid to all workers performing work in the classification under this award from the first day on which work is performed in the classification. (d) Whenever the minimum wage rate prescribed in the award for a class of laborers or mechanics includes a fringe benefit which is not expressed as an hourly rate, the Contractor shall either pay the benefit as stated in the wage determination or shall pay another bona fide fringe benefit or an hourly cash equivalent thereof. (e) If the Contractor does not make payments to a trustee or other third person, the Contractor may consider as part of the wages of any laborer or mechanic the amount of any costs reasonably anticipated in providing bona fide fringe benefits under a plan or program; provided, that the Secretary of Labor has found, upon the 13 written request of the Contractor, that the applicable standards of the Davis -Bacon Act have been met. The Secretary of Labor may require the Contractor to set aside in a separate account assets for the meeting of obligations under the plan or program. The minimum wages to be paid laborers and mechanics under this award involved in performance of work at the project site, as determined by the Secretary of Labor to be prevailing for the corresponding classes of laborers and mechanics employed on projects of a character similar to the contract work in the pertinent locality, are included as an attachment to this award. These wage rates are minimum rates and are not intended to represent the actual wage rates that the Contractor may have to pay. Payrolls and Basic Records (a) Payrolls and basic records relating thereto shall be maintained by the Contractor during the course of the work and preserved for a period of 3 years thereafter for all laborers and mechanics working at the site of the work. Such records shall contain the name, address, and social security number of each such worker, his or her correct classification, hourly rates of wages paid (including rates of contributions or costs anticipated for bona fide fringe benefits or cash equivalents thereof of the types described in section 1(b)(2)(B) of the Davis -Bacon Act), daily and weekly number of hours worked, deductions made, and actual wages paid. Whenever the Secretary of Labor has found, under paragraph (d) of the article entitled Davis -Bacon Act, that the wages of any laborer or mechanic include the amount of any costs reasonably anticipated in providing benefits under a plan or program described in section 1(b)(2)(B) of the Davis -Bacon Act, the Contractor shall maintain records which show that the commitment to provide such benefits is enforceable, that the plan or program is financially responsible, and that the plan or program has been communicated in writing to the laborers or mechanics affected, and records which show the costs anticipated or the actual cost incurred in providing such benefits. Contractors employing apprentices or trainees under approved programs shall maintain written evidence of the registration of apprenticeship programs and certification of trainee programs, the registration of the apprentices and trainees, and the ratios and wage rates prescribed in the applicable programs. (b)(1) The Contractor shall submit weekly for each week in which any award work is performed a copy of all payrolls to the Contracting Officer. The payrolls submitted shall set out accurately and completely all of the information required to be maintained under paragraph (a) of this article. This information may be submitted in any form desired. Optional Form WH -347 (Federal Stock Number 029 - 005- 00014 -1) is available for this purpose and may be purchased from the — Superintendent of Documents U.S. Government Printing Office Washington, DC 20402 The Prime Contractor is responsible for the submission of copies of payrolls by all subcontractors. (2) Each payroll submitted shall be accompanied by a "Statement of Compliance," signed by the Contractor or subcontractor or his or her agent who pays or supervises the payment of the persons employed under the award and shall certify -- (i) That the payroll for the payroll period contains the information required to be maintained under paragraph (a) of this article and that such information is correct and complete; (ii) That each laborer or mechanic (including each helper, apprentice, and trainee) employed on the award during the payroll period has been paid the full weekly wages earned, without rebate, either directly or indirectly, and that no deductions have been made either directly or indirectly from the full wages earned, other than permissible deductions as set forth in the Regulations, 29 CFR Part 3; and (iii) That each laborer or mechanic has been paid not less than the applicable wage rates and fringe benefits or cash equivalents for the classification of work performed, as specified in the applicable wage determination incorporated into the award. (3) The weekly submission of a properly executed certification set forth on the reverse side of Optional Form WH -347 shall satisfy the requirement for submission of the "Statement of Compliance" required by subparagraph (b)(2) of this article. 14 (4) The falsification of any of the certifications in this article may subject the Contractor or subcontractor to civil or criminal prosecution under Section 1001 of Title 18 and Section 3729 of Title 31 of the United States Code. (c) The Contractor or subcontractor shall make the records required under paragraph (a) of this article available for inspection, copying, or transcription by the Contracting Officer or authorized representatives of the Contracting Officer or the Department of Labor. The Contractor or subcontractor shall permit the Contracting Officer or representatives of the Contracting Officer or the Department of Labor to interview employees during working hours on the job. If the Contractor or subcontractor fails to submit required records or to make them available, the Contracting Officer may, after written notice to the Contractor, take such action as may be necessary to cause the suspension of any further payment. Furthermore, failure to submit the required records upon request or to make such records available may be grounds for debarment action pursuant to 29 CFR 5.12. Withholding of Funds The Contracting Officer shall, upon his or her own action or upon written request of an authorized representative of the Department of Labor, withhold or cause to be withheld from the Contractor under this award or any other Federal award with the same Prime Contractor, or any other federally assisted award subject to Davis -Bacon prevailing wage requirements, which is held by the same Prime Contractor, so much of the accrued payments or advances as may be considered necessary to pay laborers and mechanics, including apprentices, trainees, and helpers, employed by the Contractor or any subcontractor the full amount of wages required by the award. In the event of failure to pay any laborer or mechanic, including any apprentice, trainee, or helper, employed or working on the site of the work, all or part of the wages required by the award, the Contracting Officer may, after written notice to the Contractor, take such action as may be necessary to cause the suspension of any further payment, advance, or guarantee of funds until such violations have ceased. Apprentices and Trainees (a) Apprentices. (1) An apprentice will be permitted to work at less than the predetermined rate for the work they performed when they are employed- - (i) Pursuant to and individually registered in a bona fide apprenticeship program registered with the U.S. Department of Labor, Employment and Training Administration, Office of Apprenticeship and Training, Employer, and Labor Services ( OATELS) or with a State Apprenticeship Agency recognized by the OATELS; or (ii) In the first 90 days of probationary employment as an apprentice in such an apprenticeship program, even though not individually registered in the program, if certified by the OATELS or a State Apprenticeship Agency (where appropriate) to be eligible for probationary employment as an apprentice. (2) The allowable ratio of apprentices to journeymen on the job site in any craft classification shall not be greater than the ratio permitted to the Contractor as to the entire work force under the registered program. (3) Any worker listed on a payroll at an apprentice wage rate, who is not registered or otherwise employed as stated in paragraph (a)(1) of this article, shall be paid not less than the applicable wage determination for the classification of work actually performed. In addition, any apprentice performing work on the job site in excess of the ratio permitted under the registered program shall be paid not less than the applicable wage rate on the wage determination for the work actually performed. (4) Where a contractor is performing construction on a project in a locality other than that in which its program is registered, the ratios and wage rates (expressed in percentages of the journeyman's hourly rate) specified in the Contractor's or subcontractor's registered program shall be observed. Every apprentice must be paid at not less than the rate specified in the registered program for the apprentice's level of progress, expressed as a percentage of the journeyman hourly rate specified in the applicable wage determination. 15 (5) Apprentices shall be paid fringe benefits in accordance with the provisions of the apprenticeship program. If the apprenticeship program does not specify fringe benefits, apprentices must be paid the full amount of fringe benefits listed on the wage determination for the applicable classification. If the Administrator determines that a different practice prevails for the applicable apprentice classification, fringes shall be paid in accordance with that determination. (6) In the event OATELS, or a State Apprenticeship Agency recognized by OATELS, withdraws approval of an apprenticeship program, the Contractor will no longer be permitted to utilize apprentices at less than the applicable predetermined rate for the work performed until an acceptable program is approved. (b) Trainees. (1) Except as provided in 29 CFR 5.16, trainees will not be permitted to work at less than the predetermined rate for the work performed unless they are employed pursuant to and individually registered in a program which has received prior approval, evidenced by formal certification by the U.S. Department of Labor, Employment and Training Administration, Office of Apprenticeship Training, Employer, and Labor Services ( OATELS). The ratio of trainees to journeymen on the job site shall not be greater than permitted under the plan approved by OATELS. (2) Every trainee must be paid at not less than the rate specified in the approved program for the trainee's level of progress, expressed as a percentage of the journeyman hourly rate specified in the applicable wage determination. Trainees shall be paid fringe benefits in accordance with the provisions of the trainee program. If the trainee program does not mention fringe benefits, trainees shall be paid the full amount of fringe benefits listed in the wage determination unless the Administrator of the Wage and Hour Division determines that there is an apprenticeship program associated with the corresponding journeyman wage rate in the wage determination which provides for less than full fringe benefits for apprentices. Any employee listed on the payroll at a trainee rate who is not registered and participating in a training plan approved by the OATELS shall be paid not less than the applicable wage rate in the wage determination for the classification of work actually performed. In addition, any trainee performing work on the job site in excess of the ratio permitted under the registered program shall be paid not less than the applicable wage rate in the wage determination for the work actually performed. (3) In the event OATELS withdraws approval of a training program, the Contractor will no longer be permitted to utilize trainees at less than the applicable predetermined rate for the work performed until an acceptable program is approved. (c) Equal employment opportunity. The utilization of apprentices, trainees, and journeymen under this article shall be in conformity with the equal employment opportunity requirements of Executive Order 11246, as amended, and 29 CFR Part 30. Compliance with Copeland Act Requirements The Contractor shall comply with the requirements of 29 CFR Part 3, which are hereby incorporated by reference in this award. Subcontracts (Labor Standards) (a) Definition. "Construction, alteration or repair," as used in this article means all types of work done by laborers and mechanics employed by the construction Contractor or construction subcontractor on a particular building or work at the site thereof, including without limitation- - (1) Altering, remodeling, installation (if appropriate) on the site of the work of items fabricated off -site; (2) Painting and decorating; (3) Manufacturing or furnishing of materials, articles, supplies, or equipment on the site of the building or work; (4) Transportation of materials and supplies between the site of the work within the meaning of paragraphs 16 (a)(1)(i) and (ii) of the "site of the work" as defined in the article entitled Davis Bacon Act of this award, and a facility which is dedicated to the construction of the building or work and is deemed part of the site of the work within the meaning of paragraph (2) of the "site of work" definition; and (5) Transportation of portions of the building or work between a secondary site where a significant portion of the building or work is constructed, which is part of the "site of the work" definition in paragraph (a)(1)(ii) of the Davis -Bacon Act article, and the physical place or places where the building or work will remain (paragraph (a)(1)(i) of the Davis Bacon Act article, in the "site of the work" definition). (b) The Contractor or subcontractor shall insert in any subcontracts for construction, alterations and repairs within the United States the articles entitled -- (1) Davis -Bacon Act; (2) Contract Work Hours and Safety Standards Act -- Overtime Compensation (if the article is included in this award); (3) Apprentices and Trainees; (4) Payrolls and Basic Records; (5) Compliance with Copeland Act Requirements; (6) Withholding of Funds; (7) Subcontracts (Labor Standards); (8) Contract Termination -- Debarment; (9) Disputes Concerning Labor Standards; (10) Compliance with Davis -Bacon and Related Act Regulations; and (11) Certification of Eligibility. (c) The Prime Contractor shall be responsible for compliance by any subcontractor or lower tier subcontractor performing construction within the United States with all the award articles cited in paragraph (b). (d)(1) Within 14 days after issuance of the award, the Contractor shall deliver to the Contracting Officer a completed Standard Form (SF) 1413, Statement and Acknowledgment, for each subcontract for construction within the United States, including the subcontractor's signed and dated acknowledgment that the articles set forth in paragraph (b) of this article have been included in the subcontract. (2) Within 14 days after the award of any subsequently awarded subcontract the Contractor shall deliver to the Contracting Officer an updated completed SF 1413 for such additional subcontract. (e) The Contractor shall insert the substance of this article, including this paragraph (e) in all subcontracts for construction within the United States. Contract Termination -- Debarment A breach of the award articles entitled Davis -Bacon Act, Contract Work Hours and Safety Standards Act -- Overtime Compensation, Apprentices and Trainees, Payrolls and Basic Records, Compliance with Copeland Act Requirements, Subcontracts (Labor Standards), Compliance with Davis -Bacon and Related Act Regulations, or Certification of Eligibility may be grounds for termination of the whole award or in part for the Recovery Act covered work only, and for debarment as a Contractor and subcontractor as provided in 29 CFR 5.12. 17 Compliance with Davis -Bacon and Related Act Regulations All rulings and interpretations of the Davis -Bacon and Related Acts contained in 29 CFR Parts 1, 3, and 5 are hereby incorporated by reference in this award. Disputes Concerning Labor Standards The United States Department of Labor has set forth in 29 CFR Parts 5, 6, and 7 procedures for resolving disputes concerning labor standards requirements. Such disputes shall be resolved in accordance with those procedures and not the Disputes and Appeals as defined in 10 CFR 600.22. Disputes within the meaning of this article include disputes between the Contractor (or any of its subcontractors) and the contracting agency, the U.S. Department of Labor, or the employees or their representatives. Certification of Eligibility (a) By entering into this award, the Contractor certifies that neither it (nor he or she) nor any person or firm who has an interest in the Contractor's firm is a person or firm ineligible to be awarded Government awards by virtue of section 3(a) of the Davis -Bacon Act or 29 CFR 5.12(a)(1). (b) No part of this award shall be subcontracted to any person or firm ineligible for award of a Government award by virtue of section 3(a) of the Davis -Bacon Act or 29 CFR 5.12(a)(1). (c) The penalty for making false statements is prescribed in the U.S. Criminal Code, 18 U.S.C. 1001. Approval of Wage Rates All straight time wage rates, and overtime rates based thereon, for laborers and mechanics engaged in work under this award must be submitted for approval in writing by the head of the contracting activity or a representative expressly designated for this purpose, if the straight time wages exceed the rates for corresponding classifications contained in the applicable Davis -Bacon Act minimum wage determination included in the award. Any amount paid by the Contractor to any laborer or mechanic in excess of the agency approved wage rate shall be at the expense of the Contractor and shall not be reimbursed by the Government. If the Government refuses to authorize the use of the overtime, the Contractor is not released from the obligation to pay employees at the required overtime rates for any overtime actually worked. IN Page 1 of 7 General Decision Number: WI100032 09/03/2010 WI32 Superseded General Decision Number: WI20080032 State: Wisconsin Construction Type: Building Counties: Calumet, Outagamie, Sheboygan and Winnebago Counties in Wisconsin. BUILDING CONSTRUCTION PROJECTS (does not include residential construction consisting of single family homes and apartments up to and including 4 stories) Modification Number 0 1 2 3 4 ASBE0205 -010 06/01/1998 Publication Date 03/12/2010 06/04/2010 07/02/2010 08/13/2010 09/03/2010 Rates Fringes Asbestos Removal worker /hazardous material handler (I) ncludes preparation, wetting, stripping, removal, scrapping vacuuming, bagging and disposing of all insulation materials from mechanical systems whether they contain asbestos or not .........................$ 16.56 3.10 BOIL0107 -001 07/01/2009 Rates Fringes BOILERMAKER Boilermaker .................$ 33.64 19.27 Small Boiler Repair (under 25,000 lbs /hr) ..............$ 26.91 16.00 ---------------------------------------------------------------- BRWI0011 -003 06/01/2009 Rates Fringes BRICKLAYER Bricklayer, Cement Mason, Plasterer, Tile Layer ....... $ 30.06 14.87 ---------------------------------------------------------------- CARP0252 -001 06/01/2010 19 http://www.wdol.gov/wdol/scafiles/davisbacon/W132.dvb Page 2 of 7 Rates Fringes CARPENTER (Including Drywall Hanging, Acoustical work, Excluding Batt Insulation) CARPENTER & SOFT FLOOR LAYER .......................$ 30.56 13.36 MILLWRIGHT ..................$ 32.16 13.36 PILEDRIVERMAN ...............$ 31.06 13.36 ---------------------------------------------------------------- ELEC0494 -003 06/01/2010 Rates Fringes Sound & Communications Installer ...................$ 16.47 13.94 Technician ..................$ 24.65 15.13 Installation, testing, maintenance, operation and servicing of all sound, intercom, telephone interconnect, closed circuit TV systems, radio systems, background music systems, language laboratories, electronic carillion, antenna distribution systems, clock and program systems and low - voltage systems such as visual nurse call, audio /visual nurse call systems, doctors entrance register systems. Includes all wire and cable carrying audio, visual, data, light and radio frequency signals. Includes the installation of conduit, wiremold, or raceways in existing structures that have been occupied for six months or more where required for the protection of the wire or cable, but does not mean a complete conduit or raceway system. work covered does not include the installation of conduit, wiremold or any raceways in any new construction, or the installation of power supply outlets by means of which external electric power is supplied to any of the foregoing equipment or products ---------------------------------------------------------------- ELEC0494 -012 06/01/2010 CALUMET (New Holstein Twp.) & SHEBOYGAN COUNTIES Rates Fringes ELECTRICIAN ......................$ 29.02 18.41 ---------------------------------------------------------------- ELECO577 -002 06/01/2009 CALUMET (Except Township of New Holstein), OUTAGAMIE, AND WINNEBAGO COUNTIES Rates Fringes ELECTRICIAN ..................... -------------------------------- * ENGIO139 -002 06/01/2010 $ 27.40 26.5% +8.90 ------------------------- - - - - -- Rates OPERATOR: Power Equipment 20 Fringes http://www.wdol.gov/wdol/scafiles/davisbacon/W132.dvb Page 3 of 7 Group 1 .....................$ 34.62 17.75 Group 2 .....................$ 33.62 17.75 Group 3 .....................$ 32.42 17.75 Group 4 .....................$ 31.89 17.75 Group 5 .....................$ 29.82 17.75 Group 6 .....................$ 29.19 17.75 HAZARDOUS WASTE PREMIUMS: EPA Level "A" Protection: $3.00 per hour EPA Level "B" Protection: $2.00 per hour EPA Level "C" Protection: $1.00 per hour POWER EQUIPMENT OPERATORS CLASSIFICATIONS GROUP 1: Cranes, Tower Cranes and Derricks with or without attachments with a lifting capacity of over 100 tons; Cranes, Tower Cranes, and Derricks with boom, leads and /or jib lengths 176 ft or longer. GROUP 2: Backhoes (Excavators) weighing 130,000 lbs & over; Cranes, Tower Cranes and Derricks with or without attachments with a lifting capacity of 100 tons or less; Cranes, Tower Cranes, and Derricks with boom, leads, and /or jib lengths 175 ft or less; Caisson Rigs; Pile Driver GROUP 3: Backhoes (Excavators) weighing under 130,000 lbs; Travelling Crane (bridge type); Milling Machine; Concrete Paver over 27 E; Concrete Spreader and Distributor; Concrete Laser Screed; Concrete Grinder and Planing Machine; Slipform Curb and Gutter Machine; Boring Machine (Directional); Dredge Operator; Skid Rigs; Over 46 meter Concrete Pump. GROUP 4: Hydraulic Backhoe (tractor or truck mounted); Hydraulic Crane, 10 tons or less; Tractor, Bulldozer, or End Loader (over 40 hp); Motor Patrol; Scraper Operator; Bituminous Plant and Paver Operator; Screed - Milling Machine; Roller over 5 tons; Concrete Pumps 46 meter & under; Grout Pumps; Rotec Type Machine; Hydro Blaster, 10,000 psi and over; Rotary Drill Operator; Percussion Drilling Machine; Air Track Drill with or without integral hammer; Blaster; Boring Machine (vertical or horizontal); Side Boom; Trencher, wheel type or chain type having 8 inch or larger bucket; Rail Leveling Machine (Railroad); Tie Placer; Tie Extractor; Tie Tamper; Stone Leveler; Straddle Carrier; Material Hoists; Stack Hoist; Man Hoists; Mechanic and Welder; Off Road Maaerial Haulers GROUP 5: Tractor, Bulldozer, or Endloader (under 40 hp); Tampers - Compactors, riding type; Stump Chipper, large; Roller, Rubber Tire; Backfiller; Trencher, chain type (bucket under 8 inch); Concrete Auto Breaker, large; Concrete Finishing Machine (road type); Concrete Batch Hopper; Concrete Conveyor Systems; Concrete Mixers, 14S or over; Pumps, Screw Type and Gypsum); Hydrohammers, small; Brooms and Sweeeprs; Lift Slab Machine; Roller under 5 tons; Industrial Locomotives; Fireman (Pile Drivers and Derricks); Pumps (well points); Hoists, automatic; A- Frames and Winch Trucks; Hoists (tuggers); Boats (Tug, Safety, Work Barges and Launches); Assistant Engineer 21 http://www.wdol.gov/wdol/scafiles/davisbacon/W132.dvb Page 4 of 7 GROUP 6: Shouldering Machine Operator; Farm or Industrial Tractor mounted equipment; Post Hole Digger; Auger (vertical and horizontal); Skid Steer Loader with or without attachments; Robotic Tool Carrier with or without attachments; Power Pack Vibratory /Ultra Sound Driver and Extractor; Fireman (Asphalt Plants); Screed Operator; Stone Crushers and Screening Plants; Air, Electric, Hydraulic Jacks (Slip Form); Prestress Machines; Air Compressor, 400 CFM or over; Refrigeration Plant /Freese Machine; Boiler Operators (temporary heat); Forklifts; Welding Machines; Generators; Pumps over 3 "; Compressors, under 400 CFM; Heaters, Mechanical; Combination small equipment operator; Winches, small electric; Oiler; Greaser; Rotary Drill Tender; Conveyor; Elevator Operator * IRON0008 -001 06/23/2010 Rates Fringes IRONWORKER .......................$ 27.48 21.79 ---------------------------------------------------------- - - - - -- LABO0539 -001 06/01/2004 Rates Fringes Asbestos Abatement /Hazardous Waste (Preparation, removal, and Encapsulation of hazardous materials from non - mechanical systems) ....... $ 18.99 9.15 Laborers: (Excluding Blown Insulation; Including General Laborer, Carpenter Tender, Brick Mason Tender, Cement Mason Tender, Formsetter, Bottom man, Pipelayer, Shoveler) .............$ 19.19 9.15 ---------------------------------------------------------- - - - - -- PAIN0802 -008 06/01/2009 Rates Fringes PAINTER Brush, Drywall Taper ........ $ 21.87 10.07 ---------------------------------------------------------------- PAIN1204 -001 06/01/2009 Rates Fringes GLAZIER ..........................$ 27.14 13.46 ---------------------------------------------------------------- * PLUM0400 -001 05/31/2010 Rates Fringes PLUMBER /PIPEFITTER (Including HVAC work) (1) Small buildings (except industrial and 22 http://www.wdol.gov/wdol/scafiles/davisbacon/WI32.dvb Page 5 of 7 power plants) where plumbing or heating is $50,000 or less .............$ 28.70 12.77 (2) All other work .......... $ 31.65 15.04 ---------------------------------------------------------------- SFWI0669 -002 04/01/2010 Rates Fringes SPRINKLER FITTER .................$ 36.39 16.60 ---------------------------------------------------------------- * SHEE0018 -025 06/01/2010 CALUMET & SHEBOYGAN COUNTIES Rates Fringes Sheet Metal Worker (Including HVAC duct work and Technician) ... $ 31.88 16.75 ---------------------------------------------------------------- SHEE0018 -029 06/01/2010 OUTAGAMIE AND WINNEBAGO COUNTIES Rates Fringes Sheet Metal Worker (Including HVAC duct work and Technician) ... $ 30.25 19.42 ---------------------------------------------------------------- SUWI2002 -013 01/23/2002 Rates Fringes Asbestos Worker /Heat and Frost Insulator ..................$ 25.36 8.37 Laborers: Concrete Worker .............$ 16.34 3.59 Landscape ...................$ 8.73 4.90 ROOFER, Including Built Up, Composition and Single Ply Roofs ............................$ 18.01 3.28 Tile & Marble Finisher ........... $ 13.89 8.36 ---------------------------------------------------------------- TEAM0039 -004 05/01/2009 Rates Fringes TRUCK DRIVER 1 & 2 Axles .................$ 23.84 14.70 3 or more Axles .............$ 23.99 14.70 ---------------------------------------------------------- - - - - -- WELDERS - Receive rate prescribed for craft performing operation to which welding is incidental. Unlisted classifications needed for work not included within 23 http://www.wdol.gov/wdol/scafiles/davisbacon/W132.dvb Page 6 of 7 the scope of the classifications listed may be added after award only as provided in the labor standards contract clauses (29CFR 5.5 (a) (1) (ii)). In the listing above, the "SU" designation means that rates listed under the identifier do not reflect collectively bargained wage and fringe benefit rates. Other designations indicate unions whose rates have been determined to be prevailing. WAGE DETERMINATION APPEALS PROCESS 1.) Has there been an initial decision in the matter? This can be. • an existing published wage determination • a survey underlying a wage determination • a Wage and Hour Division letter setting forth a position on a wage determination matter • a conformance (additional classification and rate) ruling On survey related matters, initial contact, including requests for summaries of surveys, should be with the Wage and Hour Regional Office for the area in which the survey was conducted because those Regional Offices have responsibility for the Davis -Bacon survey program. If the response from this initial contact is not satisfactory, then the process described in 2.) and 3.) should be followed. With regard to any other matter not yet ripe for the formal process described here, initial contact should be with the Branch of Construction Wage Determinations. Write to: Branch of Construction Wage Determinations Wage and Hour Division U.S. Department of Labor 200 Constitution Avenue, N.W. Washington, DC 20210 2.) If the answer to the question in 1.) is yes, then an interested party (those affected by the action) can request review and reconsideration from the Wage and Hour Administrator (See 29 CFR Part 1.8 and 29 CFR Part 7). Write to: Wage and Hour Administrator U.S. Department of Labor 200 Constitution Avenue, N.W. Washington, DC 20210 The request should be accompanied by a full statement of the interested party's position and by any information (wage payment data, project description, area practice material, etc.) that the requestor considers relevant to the issue. 3.) If the decision of the Administrator is not favorable, an interested party may appeal directly to the Administrative 24 http://www.wdol.gov/wdol/scafiles/davisbacon/W132.dvb Page 7 of 7 Review Board (formerly the Wage Appeals Board). Write to: Administrative Review Board U.S. Department of Labor 200 Constitution Avenue, N.W. Washington, DC 20210 4.) All decisions by the Administrative Review Board are final. END OF GENERAL DECISION 25 http://www.wdol.gov/wdol/scafiles/davisbacon/\VI32.dvb PREVAILING WAGE RATE DETERMINATION Issued by the State of Wisconsin Department of Workforce Development Pursuant to s. 66.0903, Stats. Issued On: 7/19/2010 DETERMINATION NUMBER: 201002917 EXPIRATION DATE: Prime Contracts MUST Be Awarded Or Negotiated On Or Before 1/14/2011. If NOT, You MUST Reapply. DESCRIPTION OF PROJECT: WINNEBAGO COUNTY SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT PROJECT NO: MA09 -10 LOCATION OF PROJECT: CITY OF OSHKOSH, WINNEBAGO COUNTY, WISCONSIN CONTRACTING AGENCY: WINNEBAGO COUNTY CLASSIFICATION: Contractors are required to call the Department of Workforce Development if there are any questions regarding the proper trade or classification to be used for any worker on a public works project. OVERTIME: Time and one -half must be paid for all hours worked over 10 hours per day and 40 hours per calendar week and for all hours worked on Saturday, Sunday and the following six (6) holidays: January 1; the last Monday in May; July 4; the 1st Monday in September; the 4th Thursday in November; December 25; the day before if January 1, July 4 or December 25 falls on a Saturday; the day following if January 1 July 4 or December 25 falls o a Sunday. FUTURE INCREASE: If indicated for a specific trade or occupation, the full amount of such increase MUST be added to the "TOTAL" indicated'for such trade or occupation on the date(s) such increase(s) becomes eff ective. PREMIUM PAY: If indicated for a specific trade or occupation, the full amount of such pay MUST be added to the "HOURLY BASIC RATE OF PAY" indicated for such trade or occupation whenever such pay is applic SUBJOURNEY: Wage rates may be available for some of the classifications indicated below with the exception of laborers, truck drivers and heavy equipment operators. Any employer that desires to use any subjourney classification on this project MUST request the applicable wage rate from this department PRIOR to the date such classification is used on this project Form ERD -10880 is available for this purpose. BUILDING O R HEAVY CONSTRUCTION Includes sheltered enclosures with walk -in access for the purpose of housing persons, employees, machinery, equipment or supplies and non - sheltered work such as canals, dams, dikes, reservoirs, storage tanks, etc. A sheltered enclosure need not be "habitable" in order to be considered a building. The installation of machinery and /or equipment, both above and below grade level, does not change a project's character as a building. On -site grading, utility work and landscaping are included within this definition. Residential buildings of four (4) stories or less, agricultural buildings, parking lots and driveways are NOT included within this definition. Fringe Benefits Must Be Paid On All Hours Worked HOURLY HOURLY BASIC RATE FRINGE TRADE OR OCCUPATION OF PAY BENEFITS TOTAL - - - - -$ ------------- $------- - - - - $- -------------------------------------------------------------- - - - - -- --- - - - - -- ----------------------- Acoustic Installe ------ - - - -- -- - - - - -- -------------------------------------- 27.51 13.46 - - - - -- 4 0.97 - - - -- Boilermaker - -- --------- - - - - -- 33.64 -------------------------------------- 19.27 52.91 ----- - - - - -- --- - - - - -- Bricklayer, Blocklayer or Stonemason 30.06 15.18 45.24 Fut ure - Increase( - s): - Add $l.9505/31/201 0 ---- - - - - -- - -- ----------------------------------------------------------- Cabinet Installer 27.51 13.46 40.97 Carpenter -------------------------------------------------------- 27.51 ---------- 13.46 -------- 40.97- Car Layer or Soft Floor Coverer ------------------------ --- - - -- 27.51 -- ------------------------------ 13.46 40.97 Cement Finisher 30.06 15.17 45.23 --- Future $1.95 05/31/2010 ------- - - - - -- - ------------------------------------------------------------ - - - - -- 26 Determination No. 201002917 Paae 2 Fringe Benefits Must Be Paid On All Hours Worked HOURLY HOURLY BASIC RATE FRINGE TRADE OR OCCUPATION OF PAY BENEFITS TOTAL $ -------------- $-------------- $ ---------- $---- - - - - -- $ - - - - -- -------------------- - - - - -- ------------------------------ -------------------------------------------------------------- Drywall_Taper or Finisher - - - -- --------------------------------------------------------------- - - -------------------------------------------- 18.00 9.13 27.13 Electrician 27.40 16.29 43.69 Elevator Constructor --- - - - - -- ------------------------------------ 38.23 --------- 16.47 -------- 54.70 ---------------- - - - - -- Fence Erector 22.50 3.00 25.50 Fire Sprinkler_ Fitter ------------------------------------------------ 36.89 --------- 16.10 -------- 52.99 Glazier 25 ---------- 13.04 -------- 38.44 ----------- - - - - -- ------------------------------------------------------ Heat Insul 28.12 _ ------- 17.03 - 1.4 - - - 45.15 - -- - 34.27 -- - ----- ---- ----- ---------------------------- Insulator or Blown) ----)----------------------------------------- - 2.8 - - 2 7 2.8 ------- - - - 1 0 1.4 - - - - - -- - 34.27 Ironworker -- ------------------------------------------ 27.93 --------- -------- 20.59 48.52 --------- - - - - -- - Lather 27.51 - --------- 13.46 _______40.97 Line Constructor Electrical 34.57 19.87 54.44 Marble Finisher 27.66 14.92 42.58 ---Future - Increases : -Add - $1.78 - - on 6/1/2010; Add - $1.78 on - 6/1/2011 ------------- --- - - - -------- - - - - - ---------------------------------------------- Marble Mason 34.58 14.92 49.50 Future Increase(s): Add $1_.95 on 6/1/2010 Metal Building Erector ----- - - - - -- 24.91 ----------- 4.49 -------- 29.40 Millwri�ht_______ ______ - - - -- -------------------------------------------------------- 29.11 ---------------------------- - 13.46 42.57 Overhead In staller 25.94 13.63 39.57 ---------- - - - -- -------------------------------------------- P ainte r 20.75 6.05 26.80 Pavement Marking Operator 24.10 ---------- 9.73 -------- 33.83 _ Piledriver 28.01 13.46 41.47 Pipeline Fuser or (Gas or Utility) ------------------------------- 29.27 --------- 15.89 -------- 45.16 Plasterer 30.06 15.17 45.23 Future Increase(s): Add $1.95 /hr on 5/31/2010. --- -------- - - - - - - ---------------------- - - - - -- ----------------- - - - - -- - Plumber 31.43 14.46 45.89 Refrigeration Mechanic --------------------------------------------- 31.43 --------- 14.46 -------- 45.89 Roofer or Waterproofer_ _ _ _ _ _ _ ------- - - - - -- ------------------------------------------------ 20.25 8.99 - - - - -- 2 9.24 - - - -- Sheet Metal Worker 28.86 18.19 47.05 --- Future $2 /hr on_6/1/2010. ------- - - - - -- - ------------------------------------------------------------------ Steamfitter 31 -------- 14.46 - - -- - - 45.89 - - -- ---------------------------------------------------------------------- Teledat Tec hnician or Installer ---------------------------------------------------------------- 21.26 11.40 32.66 - - - - -- ---------- - - - - -- Temperature Control - - - -- ----------------------------------------------------------------------------------- 31.43 13.56 44.99 Terrazzo Fin-isher -- ---------------------------------------------------------- 25.50 4.21 29.71 ---------------- - - - - -- Terrazzo Mechanic ----------------------------- 31.16 --- ----------- 15.98 ------------ 47.14 ---- - -------- - - - - ------------------ Tile 23.96 ------ ---------- 15.80 ---- -------- 39.76 ----- - - - - ----------------------- Tile Setter 30.06 15.18 45.24 Future Increases : Add $1.95 /hr on 5/31/2010. ----------- - - - - -- -- - - - - -- ---------------- - - - - -- ---------------------- ----- -- - ---------- Tuckpointer, Caulker or Cleaner 23.85 11.83 35.68 Underwater Diver (Except Great Lakes )____________ ___ ___ ___ __ _____ - -- - - -- - - - -- _33.00 --------- -- 13.26 - - Well DrillerorPump Installer ---------------------------------------- ---------- - - - - -- -------------------------------------------- 24.22 14.80 39.02 Siding_Installer_ 13.00 0.72 13.72 Heavy Equipment Operator = ELECTRICAL _LINE CONSTRUCTION ONLY 26.35 12.39 38.74 Light_Eguipment Operator_ _ELECTRICAL LINE CONSTRUCTION ONLY 37.16 14.82 _ _ 51.98 Heavy Truck Driver _ELECTRICAL LINE CONSTRUCTION ONLY_ _ _ _ _ - -- -- - -- - -- -- ---- - - - - -- ------- - - - - -- - - - - - -- _ _ _ 18.00 _ _ _ - - - -- _ - _ _ - _14.75 - -- 32.75 -- --- 27 Determination No. 201002917 Page 3 Fringe Benefits Must Be Paid On All Hours Worked HOURLY HOURLY 35.19 BASIC RATE FRINGE TRADE OR OCCUPATION OF PAY BENEFITS TOTAL ------------------- - - - - -$ ------------- $---- - - - - -- $ - - - - -- -------------------------------------------------------------- ---------- - - - - -- -- - -- Light Truck Driver - ELECTRICAL LINE CONSTRUCTION ONLY ------------------------------- - - - - -- 22.47 _ _ _ - _ _ _ - _11.78 _ _ _ _ - _ _ 34.25 - Gro undman - ELECTRICAL LINE CONSTR ONLY 31.11 -------- 1 5.39-------- 46.50 TRUCK DRIVERS n Axle Two - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Sing Ie & ----- Two --- Axle --------------------------------------- - - - - -- 22.2 2.2 2 14.67 ---- - - - - -- 4.6 - - - - - -- - 36.89 89 ThreeorMoreAxle ------------------------------------------------ 25.81 ---------- 11.15 -------- 36.96 Articulated, Euclid, Dumptor, Off Road Material Hauler 24.52 17.35 41.87 Future Increase(s): Add $1.85/hr on 6/1/10; Add $1.95/hr on 6/1/11; Add $2 /hr on 6/1/12; Add $2 /hr on 6/1/13. Premium Pay: For "Airport Pavement or State Highway Construction" project type only, add $1.50 /hr for work on projects involving temporary traffic control setup, for lane and shoulder closures, when work under artificial illumination conditions is necessary as required by the project provisions (including prep time prior to and /or --- cleanup_after such time period)._ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Pavement Marking Vehicle ------------------------------------------ 19.25 --------- 10.84 -------- 30.09 Truck Mechanic --------------------------------------------- - - - - -- 25.81 ----------- 11.15 - - - - - -- 36.96 LABORERS --------- - - - - -- -- - -- - - - - - -- ------------------------------------------- General Laborer 22.81 12.38 35.19 Future Increase(s): Add $1.65/hr on 5/3112010. Pr emium Pay: Add $1.00 /hr_for certified welder and pipelayer_ Add -- - - - - -- ------ - ------ - - - - -- $.25 /hr for mason tender -- ------------ ------------------ Asbestos A Worker - -- -------------------------------------------------------------- 15.50 8.69 24.19 - --- - - - - -- --- - - Landscaper ------------------------------------------------------ 18.00 2.84 20.84 Gas or Utility Pipeline Laborer (Other Than Sewer and Water) -------------- 18.34 --------- 11.15 -_ _ _ _ _ _ _ 29.49 Fiber Optic Laborer (Outside, Other Than Concrete Encased) -------------- 17.46 --------- 11.17 -_ _ _ _ _ 28.63 _ Rail T rack Labor 22.41 7.36 29.77 HEAVY EQUIPMENT OPERATORS SITE PREPARATION, UTILITY AND LANDSCAPING WORK ONLY ---- - - - - -- --------------------------------------------------------------------------- Crane; Backhoe (Track Type); Tractor or Truck Mounted Hydraulic Backhoe; 30.97 17.35 48.32 Gradall (Cruz -Aire Type); Mechanic or Welder; Bulldozer or Endloader; Grader or Motor Patrol; Scraper (Self Propelled or Tractor Drawn) 5cu yards or more capacity; Power Subgrader; Asphalt Milling Machine; Boring Machine (Horizontal, Vertical or Directional); Air Track, Rotary or Percussion Drilling Machine; Trencher; Post Hole Digger or Driver; Tug or Launch (not performing work on the Great Lakes) Future Increase(s): Add $1.85 /hr on 6/1/10; Add $1.95/hr on 6/1/11; Add $2 /hr on 6/1/12; Add $2 /hr on 6/1/13. Premium Pay: For "Airport Pavement or State Highway Construction" project type only, add $1.50 /hr for work on projects involving temporary traffic control setup, for lane and shoulder closures, when work under artificial illumination conditions is necessary as required by the project provisions (including prep time prior to and /or _cleanup_after such time period). _ _ _ _ _ _ _ _ --------------------------------- Farm or Industrial Type Tractor; Greaser; Compactor (Self - Propelled); 27.82 13.35 41.17 Broom or Sweeper; - Environmental - Burner ------- - - - - -- ------ - - - -- ----------------------------- - - - - -- - - - - -- Crusher, Screening or Wash Plant; Air Compressor (400 CFM or Over); 31.32 16.05 47.37 Pump (3 Inch or Over) or Well Points; Refrigeration Plant or Freeze Machine; Skid Steer Loader (With or Without Attachments); Skid Rig; Stump Chipper; Mulcher; Vibratory Hammer or Extractor Future Increase(s): Add 6/1/2010; Add $1.85/hr on /M 1 - Determination No. 201002917 Paqe 4 Fringe Benefits Must Be Paid On All Hours Worked HOURLY HOURLY BASIC RATE FRINGE TRADE OR OCCUPATION OF PAY BENEFITS TOTAL ------------------------- - - - - -- ---------------- - - - - -- $--------------------------- - - - - -- HEAVY EQUIPMENT OPERATORS EXCLUDING SITE PREPARATION, UTILITY, PAVING AND LANDSCAPING WORK ------------------------------------------------------------------------------------------------ Crane, Tower Crane or Derrick, With or Without Attachments, With a Lifting 33.37 17.16 50.53 Capacity of Over 100 Tons; Crane, Tower Crane or Derrick, With Boom, Leads and /or Jib Lengths Measuring 176 Feet or Over Future Increase(s): Add $2.05 /hr on 5/31/2010. Premium Pay: Add $.50 /hr for cranes with lifting capacity at 200 ton: Add $1.00 /hr. at 300 ton; Add $1.50 /hr at --- 400 ton; 500 ton. ------------------------------------------------------------------------------------------ Crane, Tower Crane or Derrick, With or Without Attachments, With a Lifting 32.37 17.16 49.53 Capacity of 100 Tons or Under; Crane, Tower Crane or Derrick, With Boom, Leads and /or Jib Lengths Measuring 175 Feet or Under; Backhoe (Track Type) Having a Mfgr.'s Rated Capacity of 130,000 Lbs. or Over; Traveling Crane (Bridge Type); Caisson Rig; Pile Driver; Dredge (Not Performing Work on the Great Lakes) Future Increase(s): Add $2.05 /hr on 5/31/2010. - Premium - Pay:_Add $.25 /hr_for cranes with lifting - capacity of 45 over. ------ - - - -- --------- - - - - - --------------------------- - - - - -- - Crane (Go -Devil Type) or Truck Mounted Hydraulic Crane (10 Tons or 27.82 17.64 45.46 Under); Backhoe (Track Type) Having a Mfgr.'s Rated Capacity of Under 130,000 Lbs.; Tractor or Truck Mounted Hydraulic Backhoe; Gradall (Cruz -Aire Type); Mechanic or Welder; Bulldozer or Endloader; Grader or Motor Patrol; Scraper (Self Propelled or Tractor Drawn) 5 cu yards or more capacity; Concrete Pump, Grout Pump or Concrete Conveyor (Rotec or Bidwell Type); Concrete Breaker (Manual or Remote); Concrete Batch Plant; Power Subgrader; Concrete Spreader; Concrete Paver; Concrete Grinder or Planing Machine; Concrete Conveyor System; Concrete Slipform Placer; Curb and Gutter Machine; Roller (Over 5 Ton); Shouldering Machine; Boring Machine (Horizontal, Vertical or Directional); Air Track, Rotary or Percussion Drilling Machine; Straddle Carrier or Travel Lift; Forklift (Machinery Moving or Steel Erection); Manhoist or Elevator; Material or Stack Hoist; Trencher; Sideboom; Hydro - Blaster (10,000 PSI or Over); Post Hole Digger or Driver; Railroad Track Rail Leveling Machine, Tie Placer, Extractor, Tamper, Stone Leveler or Rehabilitation_ Equipment --- - ------- - ------------------------------------- ----------- ------ ------- - - - - -- Farm or Industrial Type Tractor; Greaser; Compactor (Self - Propelled); 27.19 16.83 44.02 Concrete Saw (Vermeer Type); Concrete Bump Cutter or Grooving Machine; Tining or Curing Machine; Roller (5 Tons or Under); Broom or Sweeper; Hoist Tugger); - Environmental Burner ------------------------------------------------------------------------ Crusher, Screening or Wash Plant; Air, Electric or Hydraulic Jacking System; 28.19 17.16 45.35 Air Compressor (400 CFM or Over); Generator (150 KW or Over); Pump (3 Inch or Over) or Well Points; Refrigeration Plant or Freeze Machine; Skid Steer Loader (With or Without Attachments); Robotic Tool Carrier (With or Without Attachments); Skid Rig; Stump Chipper; Mulcher; Vibratory Hammer or Extractor Future Increase(s): Add $1.80 /hr on 5/31/2010. --------------------------- - - - - -- ------------- - - - - -- -------- - - - - -- ----------- Oiler; Forklift 28.19 17.16 45.35 Future Increase(s): Add $1.80 /hr on 5/31/2010. Gas or Utility Pipeline, Sewer and Water_(Primwy Equipment) - _ _ _ _ - _32.71_ _ _ - _ -- _ _ _18.53 -------- 5124 Gas or Utility Pipeline, Except Sewer and Water (Secondary Equipment) 28.12 16.40 44.52 Future Increase(s):_Add $1.60 /hr 6/112010; Add $1.60 /hr on - - - - - -- - - - -- ------------ - - - - -- --------------------------------------- --- -------- Fiber Optic Cable Equipment ----------------------------------------- 22.79 --------- 15.30-------- 38.09 - Determination No. 201002917 e5 Fringe Benefits Must Be Paid On All Hours Worked HOURLY HOURLY BASIC RATE FRINGE TRADE OR OCCUPATION OF PAY BENEFITS TOTAL -------------------------------------------------------------- $ $ $ - --- Future Increase(s): Add $1.75 /hr on 2/1/10; Add $1.75/hr on . This document MUST BE POSTED by the CONTRACTING AGENCY in at least one conspicuous and easily accessible place on the site of the project. A local governmental unit may post this document at the place normally used to post public notices if there is no common site on the project. This document MUST remain posted during the entire time any worker is employed on the project and MUST be physically incorporated into the specifications and all contracts and most subcontracts. If you have any questions, please write to the Equal Rights Division, Labor Standards Bureau, P.O. Box 8928, Madison, Wisconsin 53708 or call (608) 266 -0028. The following statutory provisions apply to local governmental unit public works projects and are set forth below pursuant to the requirements of s. 66.0903 (8), Stats. Each contractor, subcontractor or agent thereof performing work on a project that is subject to this section shall keep full and accurate records clearly indicating the name and trade or occupation of every person described in sub. (4) and an accurate record of the number of hours worked by each of those persons and the actual wages paid therefor. Any contractor, subcontractor or agent thereof, who fails to pay the prevailing wage rate determined by the department under sub. (3) or who pays less than 1.5 times the hourly basic rate of pay for all hours worked in excess of the prevailing hours of labor determinded under sub.(3), shall be liable to any affected employe in the amount of his or her unpaid wages or his or her unpaid overtime compensation and in an additional equal amount as liquidated damages. An action to recover the liability may be maintained in any court of competent jurisdiction by any employe for and in behalf of that employe and other employes similarly situated. No employe may be a party plaintiff to any such action unless the employe consents in writing to become such a party and the consent is filed in the court in which the action is brought. Notwithstanding s. 814.04 (1), the court shall, in addition to any judgment awarded to the plaintiff, allow reasonable attorney fees and costs to be paid by the defendant. 91111 Disclaimer Effective May 1, 2007 employers performing work on public works construction projects in.Wisconsin for municipal government and state building. projects will be required to have a written substance abuse testing program in place. The provisions of this requirement are contained in Act 181. The Department of Workforce Development is not responsible for enforcement of this law or authorized to answer questions concerning the provisions of Act 181. For legal advice on complying with Act 181 you may wish to consult with a private attorney. 2005 Assembly Bill 736 Date of enactment: March 22, 2006 Date of publication *: April 5, 2006 2005 WISCONSIN ACT 181 AN ACT to create 103.503 of the statutes; relating to: substance abuse by employees who are required to be paid the prevailing wage rate for work performed on projects of public works, other than state highway projects. The people of the state of Wisconsin, represented in senate and assembly, do enact as follows: SECTION 1. 103.503 of the statutes is created to read: 103.503 Substance abuse prevention on public works projects. (1) DEFINITIONS. In this section: (a) "Accident" means an incident caused, contrib- uted to, or otherwise involving an employee that resulted or could have resulted in death, personal injury, or prop- erty damage and that occurred while the employee was performing the work described in s. 66.0903 (4) or 103.49 (2m) on a project. (b) "Alcohol" has the meaning given in s. 340.01 (lq)• (c) "Contracting agency" means a local governmen- tal unit, as defined in s. 66.0903 (1) (d), or a.state agency, as defined in s. 103.49 (1) (0, that has contracted for the performance of work on a project. (d) "Drug" means any controlled substance, as defined in s. 961.01 (4), or controlled substance analog, as defined in s. 961.01 (4m), for which testing is required by an employer under its substance abuse prevention pro- gram under this section. (e) "Employee" means a laborer, worker, mechanic, or truck driver who performs the work described in s. 66.0903 (4) or 103.49 (2m) on a project. (f) "Employer" means a contractor, subcontractor, or agent of a contractor or subcontractor that performs work on a project. (g) "Project" mean a project of public works that is subject to s. 66.0903 or 103.49. (2) SUBSTANCE ABUSE PROHIBITED. No employee may use, possess, attempt to possess, distribute, deliver, or be under the influence of a drug, or use or be under the influ- ence of alcohol, while performing the work described in s. 66.0903 (4) or 103.49 (2m) on a project. An employee is considered to be under the influence of alcohol for pur- poses of this subsection if he or she has an alcohol con- centration that is equal to or greater than the amount spe- cified in s. 885.235 (1g) (d). (3) SUBSTANCE ABUSE PREVENTION PROGRAMS REQUIRED. (a) Before an employer may commence work on a project, the employer shall have in place a written program for the prevention of substance abuse among its employees. At a minimum, the program shall include all of the following: 1. A prohibition against the actions or conditions spe- cifred in sub. (2). 2. A requirement that employees performing the work described in s. 66.0903 (4) or 103.49 (2m) on a proj- ect submit to random, reasonable suspicion, and post —ac- cident .drug and alcohol testing and to drug and alcohol Section 991.11, WISCONSIN STATUTES 2003 -04 :Effective date of acts. "Every act and every portion of an act enacted by the legislature over the governor's partial veto which does not expressly prescribe the time when it takes effect shall take effect. on the day after its date of publication as designated" by the secretary of state [the date of publication may not be more than 10 working days after the date of enactment] . ERD- 16770 -P (N. 01 /2010) 31 2005 Wisconsin Act 181 —2— 2005 Assembly Bill 736 testing before commencing work on a project, except that testing of an employee before commencing work on a project is not required if the employee has been partici- pating in a random testing program, during the 90 days preceding the date on which the employee commenced work on the project. 3. A procedure for notifying an employee who vio- lates sub. (2), who tests positive for the presence of a drug in his or her system, or who refuses to submit to drug or alcohol testing as required under the program that the employee may not perform work on a project until he or she meets the conditions specified in sub. (4) (b) 1. and 2. (b) Each employer shall be responsible for the cost of developing, implementing, and enforcing its sub- stance abuse prevention program, including the cost of drug and alcohol testing of.its employees under the pro- gram. The contracting agency is not responsible for that cost, for the cost of any medical review of a test result, or for any rehabilitation provided to an employee. (4) EMPLOYEE ACCESS TO PROJECT. (a) No employer may permit an employee who violates sub. (2), who tests positive for the presence of a drug in his or her system, or who refuses to submit to drug or alcohol testing as required under the employer's substance abuse preven- tion program under sub. (3) to perform work on a project until he or she meets the conditions specified in par. (b) 1. and 2. An employer shall immediately remove an employee from work on a project if any of the following occurs: 1. The employee violates sub. (2), tests positive for the presence of a drug in his or her system, or refuses to submit to drug or alcohol testing as required under the employer's substance abuse prevention program. 2. An officer or employee of the contracting agency has a reasonable suspicion that the employee is in viola- tion of sub. (2) and requests the employer to immediately remove the employee from work on the project. (b) An employee who is barred or removed from work on a project under par. (a) may commence or return to work on the project upon his or her employer providing to the contracting agency documentation showing all of the following: 1., That the employee has tested negative for the pres- ence of drugs in his or her system and is not under the influence of alcohol as described in sub. (2). 2. That the employee has been approved to com- mence or return to work on the project in accordance with the employer's substance abuse prevention program. (c) Testing for the presence of drugs or alcohol in an employee's system and the handling of test specimens shall be conducted in accordance with guidelines for lab- oratory testing procedures and chain —of— custody proce- dures established by the substance abuse and mental health services administration of the federal department of health and human services. (5) LOCAL ORDINANCES; STRICT CONFORMITY REQUIRED. A local governmental unit, as defined in s. 66.0903 (1) (d), may enact an ordinance regulating the conduct regulated under this section only if the ordinance strictly conforms to this section. SECTION 2. Initial applicability. (1) This act first applies to a contract to perform work on a project, as defined in section 103.503 (1) (g) of the statutes, as created by this act, for which bids are opened on the effective date of this subsection or, if bids are not solicited for the contract, to a contract to perform such work entered into on the effective date of this subsection, except that this This act first applies to an employee who is affected by a collective bargaining agreement that con- tains provisions inconsistent with this act on the day on which the collective bargaining agreement expires or is extended, modified, or renewed, whichever occurs first. SECTION 3. Effective date. (1) This act takes effect on the first day of the 13th month beginning after publication. 32 State of Wisconsin Department of Workforce Development Disclosure of Ownership Equal Rights Division The statutory authority for the use of this form is prescribed in Sections 66.0903(12)(d) and 103.49(7)(d), Wisconsin Statutes. The use of this form is mandatory. The penalty for failing to complete this form is prescribed in Section 103.005(12), Wisconsin Statutes. Personal information you provide may be used for secondary purposes [Privacy Law, s. 15.04(1) (m), Wisconsin Statutes] (1) On the date a contractor submits a bid to or completes negotiations with a state agency or local governmental unit, on a project subject to Section 66.0903 or 103.49, Wisconsin Statutes, the contractor shall disclose to such state agency or local governmental unit the name of any "other construction business ", which the contractor, or a shareholder, officer or partner of the contractor, owns or has owned within the preceding three (3) years. (2) The term "other construction business" means any business engaged in the erection, construction, remodeling, repairing, demolition, altering or painting and decorating of buildings, structures or facilities. It also means any business engaged in supplying mineral aggregate, or hauling excavated material or spoil as provided by Sections 66.0903(3), 103.49(2) and 103.50(2), Wisconsin Statutes. (3) This form must ONLY be filed, with the state agency or local governmental unit that will be awarding the contract, if both (A) and (B) are met. (A) The contractor, or a shareholder, officer or partner of the contractor: (1) Owns at least a 25% interest in the "other construction business ", indicated below, on the date the contractor submits a bid or completes negotiations. (2) Or has owned at least a 25% interest in the 'other construction business" at any time within the preceding three (3) years. (B) The Wisconsin Department of Workforce Development (DWD) has determined that the "other construction business" has failed to pay the prevailing wage rate or time and one -half the required hourly basic rate of pay, for hours worked in excess of the prevailing hours of labor, to any employee at any time within the preceding three (3) years. Other Construction Business Name of Business Street Address or P O Box City State Zip Code Name of Business Street Address or P O Box City State Zip Code Name of Business Street Address or P O Box City State Zip Code Name of Business Street Address or P O Box City State Zip Code I hereby state under penalty of perjury that the information, contained in this document, is true and accurate accordina to mv knowled a and belief. Print the Name of Authorized Officer Signature of Authorized Officer Date Signed Name of Corporation, Partnership or Sole Proprietorship Street Address or P O Box City State Zip Code If you have any 3 c�iestions call (608) 266 -6861 ERD -7777 (R. 03/2009) State of Wisconsin Department of Workforce Development Equal Rights Division Prime Contractor Affidavit of Compliance With Prevailing Wage Rate Determination Authorization for this form is provided under Sections, 66.0903(9) (b) and 103.49(4r) (9b) Wisconsin Statutes. The use of this form is mandatory. The penalty for failing to complete this form is prescribed in Section 103.005(12), Wisconsin Statutes. Personal information you provide may be used for secondary purposes [Privacy Law, s. 15.04(1)(m), Wisconsin Statutes] This form must ONLY be filed with the Awarding Agency indicated below. State Of ) )SS County Of ) Project Name Project Number Determination Number Date Determination Issued Date of Contract Awarding Agency Date Work Completed After being duly sworn, the person whose name and signature appears below hereby states under penalty of perjury that • 1 am the duly authorized officer of the corporation, partnership, sole proprietorship or business indicated below and have recently completed all of the work required under the terms and conditions of a contract with the above -named awarding agency and make this affidavit in accordance with the requirements set forth in Section 66.0903(9)(c) or 103.49(4r)(c), Wisconsin Statutes and Chapter DWD 290 of the Wisconsin Administrative Code in order to obtain FINAL PAYMENT from such awarding agency. • 1 have fully complied with the entire wage and hour requirements applicable to this project, including all of the requirements set forth in the prevailing wage rate determination indicated above which was issued for such project by the Department of Workforce Development on the date indicated above. • 1 have received the required affidavit of compliance from each of my agents and subcontractors that performed work on this project and have listed each of their names and addresses on page 2 of this affidavit. • 1 have full and accurate records that clearly indicate the name and trade or occupation of every worker(s) that I employed on this project, including an accurate record of the hours worked and actual wages paid to such worker(s). • I will retain the records and affidavit(s) described above and make them available for inspection for a period of at least three (3) years from the completion date indicated above at the address indicated below and shall not remove such records or affidavit(s) without prior notification to the awarding agency indicated above. Name of Corporation, Partnership, Sole Proprietorship or Business Street Address or P O Box City State Zip Code Telephone Number Print Name of Authorized Officer Date Signed Signature of Authorized Officer ERD -5724 (R. 03/2009) List of Agents and Subcontractors Name Name Street Address Street Address City State Zip Code City State Zip Code Telephone Number Telephone Number Name Name Street Address Street Address City State Zip Code City State Zip Code Telephone Number Telephone Number Name Name Street Address Street Address City State Zip Code City State Zip Code Telephone Number Telephone Number Name Name Street Address Street Address City State Zip Code City State Zip Code Telephone Number Telephone Number Name Name Street Address Street Address City State Zip Code City State Zip Code Telephone Number Telephone Number Name Name Street Address Street Address City State Zip Code City State Zip Code Telephone Number Telephone Number If you have any questions call (608) 266 -6861 Page 35 State of Wisconsin Department of Workforce Development Equal Rights Division Labor Standards Bureau Request to Employ Subjourneyperson The use of this form is mandatory. The authority for the use of this form is prescribed in Section DWD 290.025, Wisconsin Administrative Code. The penalty for failing to complete this form is prescribed in Section 103.005(12), Wisconsin Statutes. Personal information you provide may be used for secondary purposes. (See Section 15.04(1) (m), Wisconsin Statutes for details.] The employer indicated below requests that the Department of Workforce Development (DWD) determine the prevailing wage rate(s) and related qualifications to enable such employer to utilize a subjourneyperson(s) on the following public works project, in accordance with the provisions of Section DWD 290.025, Wisconsin Administrative Code. 1. Name of Public Works Project County Determination Number City, Village or Township Project Number 2. Name of Employee (Last, First and Initial) I P.O. Box or Street Address w a\ City I State I Zip Code I Date of Birth I Journey Classification 3. Name of Employer (Print) Name of Person Making Request (Print) P O Box or Street Address City State Zip Code Telephone Number Title of Requestor READ CAREFULLY: I fully understand that this request is ONLY applicable to the project and employee(s) ustea aoove anu roar such ernpioyeeka/ vv lll , " I VVW1 11 under the direction of and directly assist a skilled trades employee by frequently using the tools of a skilled trades employee and will NOT regularly perform the duties of a general laborer, heavy equipment operator or truck driver. If the employee(s) indicated above regularly perform(s) the work of a different trade or occupation, he /she will be compensated for such work at the applicable journeypersons prevailing wage rate. I agree not to employ any employee as a subjourneyperson on this project until I receive written confirmation from the DWD. After such confirmation is received, I will compensate the employee(s) indicated above in strict accordance with the directions received from the DWD. Signature of Requestor Date Signed MAIL COMPLETED REQUEST TO EQUAL RIGHTS DIVISION, LABOR STANDARDS BUREAU P. O. BOX 8928 MADISON WI 53708. You may call (608) 266 -6860 if you need assistance in completing your request ERD -10880 (R. 03/2009) DIVISION 23 - HVAC Section 23 05 00 — Conn Work Results for HVAC PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Items included in this specification section include: 1. Scope. 2. Plans and specifications. 3. Existing conditions. 4. Submittals. 5. Equipment and materials. 6. Codes, permits, and fees. 7. Jurisdiction of work. 8. Operation and maintenance manuals. 9. Electrical requirements. 10. Identification. 11. General HVAC system installation. 12. Demolition. 13. Excavation and backfill. 14. Cutting and patching. 15. Coordination. 16. Painting. 17. Protection and cleaning. 18. System start -up, testing, and warranty. 1.02 SCOPE A. Drawings and general requirements of contract, including General and Supplementary Conditions and Division 1 specification sections, apply to work of this Section. B. The requirements of this specification section apply to all Division 23 specification sections C. Work shall include providing complete HVAC systems in accordance with these specifications, accompanying drawings, and the State and Local Codes pertaining to the work. Provide labor, and materials, equipment and services necessary for, and incidental to manufacture, delivery and installation of the HVAC systems and equipment which are shown on the Drawings, and herein specified. D. Minor items and accessories reasonably inferred as necessary for the completion and successful operation of the work, whether or not herein definitely specified, or indicated on the drawings, shall be furnished and installed as if so specified or indicated. 1.03 PLANS AND SPECIFICATIONS A. The HVAC Contractor shall thoroughly inspect all plans and specifications to become familiar with the class of building construction in general, kinds of floors, walls, roof, ceilings, and structural systems. ©Raasch Associates, Inc. Project No. 3226 COMMON WORK RESULTS FOR HVAC — Section 23 05 00 -1 B. Examine all other Sections of the Specifications and all other Drawings in the plan set for requirements which may affect HVAC work whether or not such work is specifically mentioned in the HVAC specifications or drawings. C. The HVAC plans show the location, amount, and kinds of ductwork, piping, accessories, specialties, and equipment required. The HVAC contractor shall review HVAC system component locations and may submit suggestions for layout revisions of any portion of the work that may appear to improve the efficiency of the system or space utilization. If such changes are approved, they shall become part of the contract after approval in writing. Such approval is limited to approval for conformity with general requirements of drawings and specifications and does not relieve the Contractor of responsibility for proper operation of the system. D. If any errors or omissions appear in Drawings, Specifications, or other documents, bidding Contractor shall notify Engineer prior to submitting bid. Should conflict occur in or between drawings and specifications, bidding contractor is deemed to have estimated more expensive way of doing work, unless a written decision was requested and obtained (addendum) before submission of Proposal as to which method or materials will be required. 1.04 EXISTING CONDITIONS A. The Contractor shall inspect the building or project site to become familiar with all conditions affecting the HVAC work. Ignorance of field conditions affecting work will not be considered as reason for additional cost of work above contract price. 1.05 SHOP DRAWINGS AND PRODUCT DATA A. Submit shop drawings and product data in accordance with requirements of Division 1 General Conditions. B. Submit shop drawings, calculations, and descriptive data for all equipment, systems, and components as indicated in the respective specification section. Manufacturers or franchised dealers shall prepare the submittal data unless equipment is of stock design. C. Drawings shall show all physical sizes and required services, installation instructions, description of operation, and testing and adjusting procedures. Submittals shall be identified by applicable specification section and equipment identification tag. 1.06 EQUIPMENT AND MATERIALS A. Comply with Division 1 requirements for equipment and substitutions. B. Materials and equipment shall be new and of the make, type, size, and quality specified. C. In multiple name product specifications, it is the responsibility of the Contractor and Equipment Supplier to verify compliance with the plans and specifications, physical dimensions to fit, electrical characteristics, and capacity equal to or greater than that scheduled. ©Raasch Associates, Inc. Project No. 3226 COMMON WORK RESULTS FOR HVAC — Section 23 05 00 -2 D. Contractor to coordinate with Architect /Engineer and other Trades on any items on accepted shop drawings that differ from the requirements of the product used as a basis of design for the plans and specifications The Contractor shall assume all costs related to installing the substituted equipment and for obtaining the required performance. E. Manufacturers not specified shall submit sufficient information for approval at least seven (7) days before bid date. 1.07 CODES, FEES AND PERMITS A. Obtain and pay for all permits and pay for all fees associated with HVAC work. B. Schedule and pay for all inspections associated with HVAC work 1.08 JURISDICTION OF WORK A. Whenever it becomes necessary for the complete fulfillment of this work for a contractor to furnish labor or material other than that which is generally accepted by trade agreement of general practice to belong to his particular trade or branch or work, the contractor shall sublet same to the contractor engaged in the trade or branch of work involved, to the end that there shall be no delay to or stoppage of work due to infringement of alleged infringement of trade agreements as to jurisdiction. 1.09 OPERATION AND MAINTENANCE INSTRUCTIONS A. The Contractor shall instruct the Owner's representative on the operation and maintenance of HVAC systems. Three (3) sets of bound instructions and parts lists of all major HVAC equipment shall be provided to the Owner before final payment will be authorized. A written acknowledgment is to be filed with the Architect /Engineer. B. Instructions shall be inserted in three -ring binders with tabbed division sheets for each system or type of equipment. Include the following information: 1. Address sheet with each equipment manufacturer, including phone number and local representative. Installing contractor address and phone number. 2. Copies of approved shop drawings. 3. Manufacturer's wiring diagrams for all electrically powered equipment. 4. System start -up and test records. 5. Temperature control drawings and control sequences. 6. Equipment parts lists. 7. Valve schedules. 8. Lubrication instructions. 9. Warranties. 10. Air and water balance reports. 11. Other items indicated by the Division 1 General requirements or information indicated in the technical specification sections. 1.10 ELECTRICAL REQUIREMENTS A. Electrical wiring, components, and motors for electrically driven HVAC equipment shall comply with requirements of specification section 23 05 13 - Motors and Electrical Work. ©Raasch Associates, Inc. Project No. 3226 COMMON WORK RESULTS FOR HVAC — Section 23 05 00 -3 PART2- PRODUCTS 2.01 IDENTIFICATION A. Stencils: Not less than 1 inch high letters or numbers for marking piping, equipment, or ductwork. B. Snap -on Pipe Markers: Provide cylindrical self - coiling plastic sheet pipe markers that snap over the piping insulation and are held in place without adhesive, tape, or straps. Include flow arrows. Letters and flow direction arrows to be not less than V high. Manufacturers: Seton, W.H. Brady. C. Name Plates: White letters on a black background, 1/16 inch thick plastic laminate, beveled edges, and screw mounting. Manufacturer: Seton, or W. H. Brady. D. Valve Tags: Round brass tags with 1 /2 inch numbers, 1/4 inch letters, 1 -1/4 inch minimum diameter, and brass s -hook or chains. Manufacturer: Seton, or W. H. Brady. E. Signs: Metal construction, baked porcelain enamel finish signs, sizes conforming to NFPA 13 and 7 -1.2, with holes and s- hooks /chains for hanging or securing and applicable labeling. Seton or equal. F. Color coding: comply with the requirements of ANSI Standard A13.1 -1996. PART 3 - EXECUTION 3.01 GENERAL HVAC SYSTEM INSTALLATION A. Equipment to be level, plumb, straight, true with walls, floors and ceilings. B. Equipment suspended from ceilings, roof joists, steel or concrete to be supported with suitable hangers, steel angle and rods and spring vibration isolators. C. Do not install duct work or piping above or within 3 feet of the vertical face of any electrical panel or switchboard. Coordinate installation with Electrical Contractor. D. Coordinate all work with other contractors prior to installation. Any installed work that is not coordinated and that interferes with other contractor's work shall be removed or relocated at the installing contractor's expense. E. Verify that all devices are compatible for the surfaces on which they will be used. This includes, but is not limited to, diffusers, register, grilles, and recessed or semi - recessed heating and/or cooling terminal units installed in/on architectural surfaces. F. Install all piping, conduit, ductwork, and accessories to permit access to equipment for maintenance and service. Coordinate the exact location of wall and ceiling access panels and doors with the General Contractor. G. Follow as closely as possible construction conditions of other trades. Make minor changes requiring additional pipe, ducts, bends or fittings necessary to meet conditions actually ©Raasch Associates, Inc. Project No. 3226 COMMON WORK RESULTS FOR HVAC — Section 23 05 00 -4 existing without additional cost to the Owner. Allow other contractors reasonable access to their work. H. Roof Mounted Equipment - Roof curbs are to be furnished by the HVAC Contractor. General and HVAC Contractor to coordinate locations and mounting requirements. Installation of curb and flashing by General Contractor. I. HVAC Systems Identification: 1. Identify equipment in mechanical rooms, on rooftops, and in unoccupied areas with engraved name plates. 2. Identify piping not less than every 30 feet, in every room, near access openings, and on both sides of wall, roof, or floor penetrations when piping is exposed. Provide flow arrows. 3. Identify valves with brass tags with system identification and chart number. Provide valve schedule with tag numbers and locations. 3.02 DEMOLITION A. Perform all demolition as indicated on the drawings to accomplish new work. Where demolition work is to be performed adjacent to existing work that remains in an occupied area, construct temporary dust partition to minimize the amount of contamination of the occupied space. Coordinate work with the Owner to minimize disruption to the existing building occupants. B. Where pipe or duct is removed and not reconnected with new work, cap ends of existing services as if they were new work. Maintain the condition of material and /or equipment that is indicated to be reused equal to that existing before work began. C. All piping, wiring and associated conduit, insulation, ductwork, and similar items demolished, abandoned, or deactivated are to be removed from the site by the Contractor. 3.03 CONCRETE WORK A. All cast -in -place concrete will be performed by the General Contractor unless otherwise noted. Provide all layout drawings, anchor bolts, metal shapes, and /or templates required to be cast into concrete or used to form concrete for support of HVAC equipment. B. Piping related cast -in -place concrete may be provided by the HVAC Contractor in conformance with the requirements of the Division 3 specifications. 3.05 CUTTING AND PATCHING A. Refer to Division 1, General Requirements, Cutting and Patching. B. General Contractor is required under his contract to leave chases, recesses, and openings in the new construction, provided that this Contractor furnish him full information as to locations and dimensions of same in all new construction. Failing to give General contractor the proper information at the time required, such cutting and patching shall be done by this Contractor. ©Raasch Associates, Inc. Project No. 3226 COMMON WORK RESULTS FOR HVAC — Section 23 05 00 -5 C. This contractor shall set all sleeves and anchors in such time as to cause no delay in the work of the General Contractor. Any cost caused by defective or ill -timed work shall be assumed by the responsible party. D. Do not endanger the stability of the structure by cutting or digging or otherwise, and do not cut or alter work of any other contractor without Architect /Engineer's consent and approval. HVAC Contractor is required to cut all openings required for HVAC system installation in existing areas, and the General Contractor will patch to match. HVAC Contractor to coordinate size and location of patching with General Contractor before bidding. E. Sleeve and seal duct openings at fire rated walls or floors per fire damper details on plans and per requirements of specification section 23 33 00 — Air Duct Accessories. Seal duct penetrations of non - dampered or non -rated partitions with fire rated insulation and sheet metal angle escutcheons. 3.06 PAINTING A. All equipment such as radiation, grilles, fans, etc., will be shipped with factory finish. HVAC Contractor shall be responsible for touching up all painted surfaces damaged during construction or in transit from factory to job site. B. Paint structural steel supports for equipment, piping, or ductwork exposed outdoors with two coats of rust proof type paint. Galvanized supports do not require painting. C. Paint piping exposed outdoors with two coats of rust proof type paint. Galvanized piping does not require painting. 3.07 PROTECTION, CLEANING, AND MAINTENANCE A. Contractor shall be entirely responsible for apparatus, equipment and appurtenance furnished by him or his sub - contractors in connection with this work and special care shall be taken to protect parts thereof in such manner as may be necessary or directed. B. Protection shall include covers, crating, sheds or other means to prevent dirt, grit, plaster or other foreign substances from entering working parts of machinery or equipment. C. Special care shall be taken to keep open ends of pipes, ducts, etc., closed while in storage or during progress of the installation. D. All ductwork and piping shall be cleaned and all filters replaced at the time the system is accepted by the Owner. E. All equipment shall be wiped clean with all traces of oil, dust, dirt, or paint spots removed. F. Touch -up paint damaged equipment surfaces to Architect /Engineer's satisfaction. G. Lubricate all bearings as recommended by the manufacturer. H. Belt drives and belts shall be properly adjusted. ©Raasch Associates, Inc. Project No. 3226 COMMON WORK RESULTS FOR HVAC — Section 23 05 00 -6 3.08 SYSTEM START -UP, TESTING, AND WARRANTY A. The HVAC Contractor shall be responsible for complete test, check and startup of all equipment that the contractor installs. The manufacturer, or trained manufacturer's representative, shall provide initial startup of roof -top unit air conditioning equipment, packaged chillers, and snake -up air equipment. B. A copy of the completed check, test and start -up report shall be placed on file with the Architect /Engineer's office for all equipment and systems noted above. C. The Contractor is to leave the entire system in mechanically proper working order. The Contractor shall correct and replace any defective material or faulty workmanship without additional charge to Owner for a period of two (2) years from date of final approval for all equipment. D. This limited guarantee is to include all materials and products needed during the guarantee period, and all service calls on the HVAC systems. END SECTION ORaasch Associates, Inc. Project No. 3226 COMMON WORK RESULTS FOR HVAC — Section 23 05 00 -7 DIVISION 23 - HVAC Section 23 05 13 - Motors and Electrical Work PART 1 - GENERAL 1.01 SECTION INCLUDES A. Electrical Coordination. B. Three phase, single speed motors. C. Single phase, single speed motors. 1.02 RELATED WORK A. Section 23 09 23- Direct Digital Control Systems. B. Section 23 74 00 - Outdoor Heating and Cooling Equipment. 1.03 REFERENCES A. ANSI/NFPA 70 - National Electrical Code B. ANSI/IEEE 112 - Test Procedure for Polyphase Induction Motors and Generators. C. ANSI/NEMA MG -1 - Motors and Generators. 1.04 SHOP DRAWINGS A. Refer to Division 1, General Conditions, Submittals. B. Include the following motor information with the equipment submittal that the motor drives: motor manufacturer, horsepower, voltage, phase, hertz, rpm, full load efficiency. C. Include project wiring diagrams prepared specifically for this work. 1.05 OPERATING AND MAINTENANCE INSTRUCTIONS A. Include manufacturer's instructions in the manuals with the specific equipment to which they apply. Also include the following information if not previously documented on shop drawings: full load power factor, service factor, NEMA design designation, insulation class, and frame type. 1.06 REGULATORY REQUIREMENTS A. Conform to applicable State and Local Building Codes. B. Electrical: Conform to requirements of ANSI/NFPA 70. C. Furnish products listed and classified by Underwriters Laboratories, Inc. as suitable for purpose specified and shown. 1.07 PROJECT CONDITIONS ©Raasch Associates, Inc. Project No. 3226 MOTORS AND ELECTRICAL WORK - Section 23 05 13 -1 A. Verify that field measurements are as shown on Drawings. B. Equipment locations shown on Drawings are approximate unless dimensioned. Locate equipment as required to meet Project Conditions. C. Determine required separation between equipment and other work. D. Determine equipment locations to avoid interference with other work. E. Coordinate equipment, duct, piping, conduit and cable installation with other Trades. Assure proper clearances and needed room to install respective systems. 1.08 ELECTRICAL COORDINATION A. Provide all motors for electrically driven mechanical equipment. B. Starters, controllers, and disconnects which are an integral part of the equipment shall be factory mounted and supplied with the unit by the Mechanical Contractor. Starters, controllers, and disconnects which are not integral to the mechanical equipment shall be provided as part of Division 26 electrical work, unless noted otherwise. C. Line voltage wiring (115 volts and over) required for the connection of heating, ventilation and air conditioning equipment to be done by the Electrical Contractor. Low voltage wiring (below 115 volts) to be done by the Mechanical Contractor. D. The Mechanical Contractor to furnish necessary controls, wiring diagrams and instruction sheets and coordinate his work with that of the Electrical Contractor to assure proper connection and operation of the controls and equipment for the HVAC System. E. The Mechanical Contractor is to mount damper motors, etc., and other devices requiring connections on mechanical equipment. Wiring by Mechanical Contractor. F. The Mechanical Contractor to be responsible for the operating of the system, temperature, safety and other controls on the work during installation and guarantee period. G. Combination starters and magnetic starters, push button stations, pilot lights, etc., to be furnished by the Electrical Contractor. See Electrical Plan Motor Schedule and Mechanical Equipment Schedules. Mechanical contractor is to supply all needed wiring for Mechanical System, not shown on electrical plan. H. Field- installed disconnect switches, fused disconnects, capped safety switches, etc., to be furnished and installed by the Electrical Contractor. I. Each motor shall be provided with a suitable disconnect, properly identified. It is the responsibility of the Mechanical Contractor to see that all such labels or other means of identification are delivered to the Electrical Contractor. J. Flexible metal Greenfield cable, of 1 /2" or larger size, in lengths not to exceed 36" shall be used for final power connections to all motorized equipment such as fans, pumps, compressors, etc. K. Electrical work shall be done in accordance with the requirements of the electrical specification, National Electrical Code, and all State and local Codes. ©Raasch Associates, Inc. Project No. 3226 MOTORS AND ELECTRICAL WORK - Section 23 05 13 -2 PART2- PRODUCTS 2.01 THREE PHASE, SINGLE SPEED MOTORS A. Use NEMA rated, three phase, 60 hertz motors for all motors 1/2 HP and larger unless specifically indicated. B. Use NEMA general purpose, continuous duty, Design B, normal starting torque, T -frame or U -frame motors with Class B or better insulation unless the manufacturer of the equipment on which the motor is being used has different requirements. Use open drip - proof motors unless totally enclosed fan - cooled, totally enclosed non - ventilated, explosion - proof, or encapsulated motors are specified in the equipment sections. C. Use grease lubricated anti - friction ball bearings with housings equipped with plugged /capped provision for relubrication, rated for minimum AFBMA 9, L -10 life of 200,000 hours. Calculate bearing load with NEMA minimum V -belt pulley with belt center line at the end of NEMA standard shaft extension. Stamp bearing sizes on nameplate. D. All motors shall have a 1.15 service factor. E. Motors scheduled for use with variable frequency drives must be rated for use with the type of drive specified, including but not limited to motor cooling. F. Motors that are part of packaged HVAC equipment that complies with the energy efficiency requirements of ASHRAE Standard 90.1 need not comply with these specifications. G. All motors 1 HP and larger, except specially wound motors and inline pump motors 56 frame and smaller, to be NEMA Premium efficiency design with full load efficiencies which meet or exceed the values listed below when tested in accordance with NEMA MG 1. FULL LOAD NOMINAL MOTOR EFFICIENCY BY MOTOR SIZE AND SPEED - - -- -Open Drip -Proof Motors----- - MOTOR - - - - - -- Nominal Motor Speed------ - HP 1200 rpm 1800 rpm 3600 rpm 1 82.5 85.5 77.0 1 -1/2 86.5 86.5 84.0 2 87.5 86.5 85.5 3 88.5 89.5 85.5 5 89.5 89.5 86.5 7 -1/2 90.2 91.0 88.5 10 91.7 91.7 89.5 15 91.7 93.0 90.2 20 92.4 93.0 91.0 - - -- Totally Enclosed Fan - Cooled - - -- ©Raasch Associates, Inc. Project No. 3226 MOTORS AND ELECTRICAL WORK - Section 23 05 13 -3 MOTOR - - - - - -- Nominal Motor Speed----- - HP 1200 rpm 1800 rpm 3600 rpm 1 82.5 85.5 77.0 1 -1/2 87.5 86.5 84.0 2 88.5 86.5 85.5 3 89.5 89.5 86.5 5 89.5 89.5 88.5 7 -1/2 91.0 91.7 89.5 10 91.0 91.7 90.2 15 91.7 92.4 91.0 20 91.7 93.0 91.0 2.02 SINGLE PHASE, SINGLE SPEED MOTORS A. Use NEMA rated 115 volt, single phase, 60 hertz motors for all motors 1/3 HP and smaller. B. Use pennanent split capacitor or capacitor start, induction run motors equipped with permanently lubricated and sealed ball or sleeve bearings and Class A insulation. Service factor to be not less than 1.35. C. Motors drawing less than 250 watts and used for intennittent service may be provided by the manufacturer of the driven equipment from their standard motor stock and does not need to conform to these specifications. PART 3 - EXECUTION 3.01 INSTALLATION A. Verify the proper rotation of each three -phase motor as it is being wired or before the motor is energized for any reason. B. Lubricate all motors requiring lubrication. Record lubrication material used and the frequency of use. Include this information in the maintenance manuals. C. All control wiring (low and line voltage) shall be provided by Division 23, unless otherwise noted on the drawings. END SECTION cORaasch Associates, Inc. Project No. 3226 MOTORS AND ELECTRICAL WORK - Section 23 05 13 -4 DIVISION 23 — HVAC Section 23 05 17 - Pipe Tube and Fittings for HVAC Systems PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and general requirements of contract, including General and Supplementary Conditions and Division 1 specification sections, apply to work of this Section. B. Extent of pipe, tube, and fittings required by this Section is indicated on drawings and /or specified in other Division 23 sections. C. Types of pipe, tube, and fittings specified in this section include the following: 1. Piping Materials: a. Steel Pipe b. PVC Plastic Pipe 2. Pipe /Tube Fittings: a. Fittings for Steel Pipe b. Fittings for PVC Plastic Pipe 3. Unions and Flanges. 4. Miscellaneous Piping Materials /Products. 1.02 QUALITY ASSURANCE A. Welding - Welding procedures and welders for all building service piping less than or equal to 15 psig shall be certified in accordance to the National Certified Pipe Welding Bureau. Welding procedures and welders for piping systems of more than 15 psig service pressure shall be qualified with the latest revision of ANSI /ASME B31.1 -Power Piping or Section IX of the ASME Boiler and Pressure Vessel Code. B. Brazing - Certify brazing procedures, brazers, and operators in accordance with ANSI /ASME B31.5, Refrigeration Piping and Heat Transfer Components 1.03 SUBMITTALS A. Product Data - Submit catalog cuts, specifications, installation instructions, and dimensioned drawings for each type of pipe, tube, and fitting. Submit piping schedule showing Manufacturer, pipe or tube weight, fitting type, and joint type for each piping system. B. Welding Certificates - Submit reports as required for piping work. 1.04 DELIVERY, STORAGE, AND HANDLING A. Provide factory- applied plastic end -caps on each length of pipe and tube. Maintain end - caps through shipping, storage and handling, as required to prevent pipe -end damage and eliminate dirt and moisture from inside of pipe and tube. B. Where possible, store pipe and tube inside and protected from weather. Where necessary to store outside, elevate above grade and enclose with durable, waterproof wrapping. ©Raasch Associates, Inc. Project No. 3226 PIPE, TUBE AND FITTINGS FOR HVAC SYSTEMS — Section 23 05 17 -1 C. Protect flanges and fittings from moisture and dirt by inside storage and enclosure, or by packaging with durable, waterproof wrapping. PART2- PRODUCTS 2.01 PIPING MATERIALS A. Steel Pipe: 1. Black Steel Pipe - ANSI /ASTM A 53. 2. Galvanized Steel Pipe - ANSI /ASTM A 53. B. PVC Plastic Pipe: ANSI /ASTM D1785, Schedule 40. 2.02 PIPE /TUBE FITTINGS A. Cast -Iron Flanged Fittings - ANSI B16.1, including bolting. B. Forged Steel Flanges - ANSI /ASME B 16.5. C. Cast -Iron Threaded Fittings - ANSI B16.4. D. Malleable Iron Threaded Fittings - ANSI B16.3; plain or galvanized as indicated. E. Threaded Pipe Plugs - ANSI B 16.14. F. Pipe Nipples - Fabricated from same pipe as used for connected pipe; except do not use less than Schedule 80 pipe where length remaining unthreaded is less than 1 -1/2 ", and where pipe size is less than 1 -1/2 ", and do not thread nipples full length (no close - nipples). G. Carbon Steel Weld Fittings: ANSI /ASME B16.9, ANSI /ASTM A234. H. Forged steel fittings (socket welded and threaded): ANSFASTM B16.11. I. PVC plastic drain, waste, and vent fittings - ANSI /ASTM D2665; socket fitting patterns, ANSI /ASTM D3311. 2.04 UNIONS AND FLANGES A. Steel Piping: 1. 2" and Smaller: ASTM A197 /ANSI B16.3 malleable iron unions with brass seats, 250 psig rated, galvanized for galvanized piping systems. 2. 2 -1/2" and Larger: ASTM A181 or A105, ANSI B16.5, forged steel flanges of a pressure class compatible with the piping service. Gasket material shall be non- asbestos and suitable for the pressure, temperature, and type of fluid service. 2.05 MISCELLANEOUS PIPING MATERIALS /PRODUCTS A. Welding Materials: Comply with Section II, Part C, ASME Boiler and Pressure Vessel Code for welding materials. ©Raasch Associates, Inc. Project No. 3226 PIPE, TUBE AND FITTINGS FOR HVAC SYSTEMS — Section 23 05 17 -2 B. PVC Solvent Welding Materials: Primer ANSI /ASTM F -656, Solvent Cement ANSI /ASTM D2564. PART 3 - EXECUTION 3.01 INSTALLATION A. Provide adequate and accessible unions for disassembly and maintenance /replacement of valves and equipment. B. Reduce sizes (where indicated) by use of reducing fittings, Align accurately at connection, within 1/16" misalignment tolerance. C. Locating piping runs, except as otherwise indicated, vertically and horizontally (pitched to drain) and avoid diagonal runs wherever possible. Orient horizontal run parallel with walls and column lines. Locate runs as shown or described by diagrams or details. D. Hold piping close to walls, overhead construction, columns and other structural and permanent- enclosure elements of building; limit clearance to 1/2" where furring is shown for enclosure or concealment of piping, but allow for insulation thickness, if any. When possible, locate insulated piping for 1.0" clearance outside insulation. E. Wherever possible in finished and occupied spaces, conceal piping from view, by locating in column enclosures, in hollow wall construction or above suspended ceilings; do not encase horizontal runs in solid partitions, except as indicated. F. Coordinate locations of HVAC system piping with ductwork, conduits and equipment of other trades to allow required clearances. Consult drawings for exact locations of piping spaces, ceiling heights, ceiling grids, light fixtures, and air terminal units before installing piping. G. Electrical Equipment Spaces - Do not run piping through transformer vaults and other electrical or electronic equipment and enclosures unless unavoidable. Install drip pan under piping that must be run through electrical spaces. H. "Weldolets" and "Threadolets" may be used for branch take -offs up to one -half the diameter of the main. Install all valves, control valves, and piping specialties, including items furnished by others, as specified or detailed. Make connections to equipment installed by others where that equipment requires piping services provided under this division. 3.02 PIPING SYSTEM JOINT A. Thread pipe in accordance with ANSI B2.1; cut threads full and clean using sharp dies. Ream threaded ends to remove burrs and restore full inside diameter. Apply pipe joint ©Raasch Associates, Inc. Project No. 3226 PIPE, TUBE AND FITTINGS FOR HVAC SYSTEMS — Section 23 05 17 -3 compound, or pipe joint tape (Teflon) where recommended by pipe /fitting manufacturer, on male threads at each joint and tighten joint to leave not more than 3 threads exposed. B. Weld pipe joints in accordance with ASME Codes and ANSI B31. C. Install solvent welded pipe joints in accordance with ASTM D2855. Saw cut piping square and smooth. Bevel ends and deburr pipe interior. Remove dirt and moisture from the mating surfaces to be joined. Apply primer to pipe and fitting with a scrubbing action. Apply solvent cement to pipe and fitting, insert pipe into fitting with a quarter turn. Hold joint for 30 seconds or until set. 3.03 CLEANING, FLUSHING, INSPECTING A. Clean exterior surfaces of installed piping systems of superfluous materials, and prepare for application of specified coatings (if any). Flush out piping systems with clean water before proceeding with required tests. Inspect each run of each system for completion of joints, supports and accessory items. 3.04 PIPING TESTS A. Test each natural section of each piping system independently but do not use piping system valves to isolate sections where test pressure exceeds valve pressure rating. Pressurize for indicated pressure and tune. B. Required test period is 2 hours. C. Repair piping systems sections which fail required piping test, by disassembly and reinstallation, using new materials to extent required to overcome leakage. Do not use chemicals, stop -leak compounds, mastics, or other temporary repair methods. D. Drain test water from piping systems after testing and repair work has been completed. END SECTION ©Raasch Associates, Inc. Project No. 3226 PIPE, TUBE AND FITTINGS FOR HVAC SYSTEMS — Section 23 05 17 -4 DIVISION 23 — HVAC Section 23 05 19 - Piping Specialties for HVAC Systems PART 1- GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and general requirements of contract, including General and Supplementary Conditions and Division 1 specification sections, apply to work of this Section. B. Extent of piping specialties required by this Section is indicated on drawings and/or specified in other Division 23 sections. C. Types of piping specialties specified in this section include the following: 1. Pipe Escutcheons 2. Dielectric Unions 3. Sleeves 4. Sleeve Seals 1.02 QUALITY ASSURANCE A. All quantities of each type of item shall be from a single manufacturer. 1.03 SUBMITTALS A. Submit catalog cuts, specifications, installation instructions, and dimensioned drawings for each type of manufactured piping specialty. Include pressure drop curve or chart for each type and size of pipeline strainer. Submit schedule showing manufacturer's figure number, size, location, and features for each required piping specialty. PART 2 - PRODUCTS 2.01 MANUFACTURED PIPING SPECIALTIES A. Provide factory - fabricated piping specialties by manufacturer for use in service indicated. Provide sizes as indicated, and connections, which properly mate with pipe, tube, and equipment connections. Where more than one type is indicated, selection is Installer's option. B. Pipe Escutcheons: 1. Pipe Escutcheons: Provide pipe escutcheons with inside diameter closely fitting pipe outside diameter, or outside of pipe insulation where pipe is insulated. 2. Select outside diameter of escutcheon to completely cover pipe penetration hole in floors, walls, or ceilings; and pipe sleeve extension, if any. 3. Furnish pipe escutcheons with nickel or chrome finish for occupied areas, prime paint finish for unoccupied areas. Provide sheet steel escutcheons, solid or split hinged. ©Raasch Associates, Inc. Project No. 3226 PIPING SPECIALTIES FOR HVAC SYSTEMS — Section 23 05 19 -1 C. Dielectric Unions: Provide standard products which effectively isolates ferrous from non - ferrous piping (electrical conductance), prevents galvanic action, stops corrosion. 2.02 SLEEVES AND SEALS A. Provide pipe sleeves of one of the following: 1. Sheet - Metal: Fabricate from galvanized sheet metal; round tube closed with snaplock joint, welded spiral seams, or welded longitudinal joint. Fabricate from the following gauges: 3" and smaller, 20 gauge; 4" to 6 ", 16 gauge; over 6 ", 14 gauge. 2. Steel -Pipe: Fabricate from Schedule 40 galvanized steel pipe; remove burs. 3. Iron -Pipe: Fabricate from cast -iron or ductile -iron pipe; remove burrs. 4. Seals for non -rated penetrations: Urethane caulk in annular space between pipe insulation (or pipe) and sleeve. PART 3 - EXECUTION 3.01 INSTALLATION OF MANUFACTURED PIPING SPECIALTIES A. Pipe Escutcheons - Install pipe escutcheons on each pipe penetration through floors, walls, partitions, and ceilings where penetration is exposed to view; and on exterior of building. Secure escutcheon to pipe or insulation so escutcheon covers penetration hole, and is flush with adjoining surface. B. Dielectric Unions - Install at each piping joint between ferrous and nonferrous piping. Comply with manufacturer's installation instructions. 3.02 INSTALLATION OF SLEEVES AND SEALS A. Install pipe sleeves of types indicated where piping passes through walls, floors, ceilings, and roofs. B. Do not install sleeves through structural members of work, except as detailed on drawings, or as reviewed by A /E. C. Install sleeves accurately centered on pipe runs. Size sleeves so that piping and insulation (if any) will have free movement in sleeve, including allowance for thermal expansion; but not less than 2 pipe sizes larger than piping run. Where insulation includes vapor - barrier jacket, provide sleeve with sufficient clearance for installation. D. Install length of sleeve equal to thickness of construction penetrated, and finish flush to surface; except floor sleeves. Extend floor sleeves 1/4" above level floor finish, and 3/4" above floor finish sloped to drain. E. Provide temporary support of sleeves during placement of concrete and other work around sleeves, and provide temporary closure to prevent concrete and other materials from entering sleeves. ORaasch Associates, Inc. Project No. 3226 PIPING SPECIALTIES FOR HVAC SYSTEMS — Section 23 05 19 -2 F. Sleeve Type: 1. Install iron -pipe sleeves at exterior penetrations, both above and below grade. 2. Install sheet -metal sleeves at interior partitions and ceilings other than suspended ceilings. 3. Core drilled openings in existing poured concrete walls do not require sleeves. G. Sleeve Seals - Install in accordance with the following: Seals for non -rated penetrations: Apply sealant to both ends or sleeve so that the space between the pipe sleeve or cored opening and the pipe or pipe insulation is completely sealed. END SECTION ©Raasch Associates, Inc. Project No. 3226 PIPING SPECIALTIES FOR HVAC SYSTEMS — Section 23 05 19 -3 DIVISION 23 - HVAC Section 23 05 29 — Hangers and Supports for HVAC Systems PART1- GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and general requirements of contract, including General and Supplementary Conditions and Division 1 specification sections, apply to work of this Section. B. Types of supports and anchors specified in this section include the following: 1. Pipe, ductwork, and equipment hangers, supports, and anchors. 2. Building attachments. 3. Structural supports and equipment stands. 4. Equipment rails and curbs. 1.02 REGULATORY REQUIREMENTS A. Provide pipe hangers and supports in compliance with the following Manufacturer's Standardization Society requirements: 1. MSS SP -58 Pipe Hangers and Supports - Materials, Design and Manufacture. 2. MSS SP -69 Pipe Hangers and Supports - Selection and Application. 3. MSS SP -89 Pipe Hangers and Supports - Fabrication and Installation. 1.03 SUBMITTALS A. Submit catalog cuts, specifications, installation instructions, and dimensioned drawings for each type of support or anchor. B. Submit pipe hanger and support schedule showing Manufacturer's figure number, size, location, and features for each required pipe hangers and support. PART 2- PRODUCTS 2.01 GENERAL HANGER AND SUPPORT REQUIREMENTS A. Manufacturer - Subject to compliance with requirements, provide hangers and supports of one of the following: 1. B -Line Systems, Inc. 2. C & S Mfg. Corp. 3. Fee and Mason. 4. Grinnell Corp. B. Use only one type by one manufacturer for each piping service. C. Select size of hangers and supports to exactly fit pipe size for bare piping, and to exactly fit around piping insulation with saddle or shield for insulated piping. D. Provide all supporting steel required for the installation of HVAC equipment and materials, whether or not it is specifically indicated or sized, including angles, channels, beams, etc. to suspend or floor support piping, piping, tanks, ductwork, and equipment. ©Raasch Associates, Inc. Project No. 3226 HANGERS AND SUPPORTS FOR HVAC SYSTEMS — Section 23 05 29 -1 E. Finish: 1. Exposed Hangers and Supports - Provide prime coat finish. 2. Corrosive Atmosphere Locations — Factory coat supports and anchors used in corrosive atmospheres with hot dip galvanizing after fabrication. Mechanical galvanized threaded products. Field cuts and damaged finishes to be field covered with zinc rich paint. Corrosive atmospheres include the following locations a. Exterior locations 2.02 PIPING HANGERS AND SUPPORTS A. Pipe Sizes 1/2" to 1 -1/2 ": 1. Adjustable Steel Clevises - MSS Type 1. 2. Adjustable Steel Band Hangers - MSS Type 7. B. Pipe Sizes 2" and Larger: 1. Adjustable Steel Clevises - MSS Type 1. 2. Steel Pipe Clamps - MSS Type 4, (limited to uninsulated piping). C. Vertical Piping Clamps (all sizes): Two -Bolt Riser Clamps - MSS Type 8. D. Wall Support: 1. Carbon steel welded bracket (with hanger - MSS Type 31. 2. Slotted steel channel with epoxy painted finish. Interlocking, split -type, bolt secured, galvanized pipe /tubing clamps. Provide flexible elastomeric /thermoplastic isolation cushion material for copper piping systems. E. Trapeze Hangers: 1. Steel Trapezes - Structural tubing or steel channels with welded spacers and hanger rods. 2. Heavy-Duty Steel Trapezes - Fabricate from steel shapes selected for loads required or as called out on drawings; weld steel in accordance with AWS standards. 2.03 BUILDING ATTACHMENTS A. Provide factory- fabricated building attachments, of one of the following MSS types listed, in accordance with MSS SP -69 published product information. 1. Top Beam C- Clamps — MSS Type 19. 2. Center Beam Clamps - MSS Type 21. 3. C- Clamps - MSS Type 23. 4. Side I -Beam Clamps - MSS Type 27. 5. Side Beam Brackets — MSS Type 34. B. Concrete Building Attachments: Concrete anchors - Expansion Type. Use drilled steel shell with plug type inserts when the inserts are placed after the concrete is poured. Concrete lug, clevis, or rod attachment plate. C. Select size of building attachments to suit hanger rods. ©Raasch Associates, Inc. Project No. 3226 HANGERS AND SUPPORTS FOR HVAC SYSTEMS — Section 23 05 29 -2 2.04 STEEL HANGER RODS: A. Threaded both ends, threaded one end, or continuous threaded, galvanized finish. Provide rods complete with adjusting and lock nuts. B. Size rods for individual hangers and trapeze supports as indicated in the following schedule. Total weight of equipment supported by a rod, including valves, fittings, pipe, pipe content, and insulation, shall not exceed the maximum load limits indicated. Maximum Load (Lbs.) (650 °F Maximum Temp.) 610 1130 1810 2710 3770 Rod Diameter (inches) 3/8 1/2 5/8 3/4 7/8 PART 3 - EXECUTION 3.01 PREPARATION A. Proceed with installation of hangers, supports and anchors only after required building structural work has been completed in areas where the work is to be installed. Correct inadequacies including (but not limited to) proper placement of inserts, anchors and other building structural attachments. 3.02 INSTALLATION OF BUILDING ATTACHMENTS A. Install building attachments at required locations within or on concrete or structural steel for proper piping support. B. Install additional building attachments where support is required for additional concentrated loads, including valves, flanges, guides, strainers, expansion joints, and at changes in direction of piping. 3.03 INSTALLATION OF HANGERS AND SUPPORTS A. Comply with MSS SP -69. B. Arrange for grouping of parallel runs of horizontal piping to be supported together on trapeze type hangers where possible. C. Install supports with maximum spacing complying with MSS SP -69. Where piping of various sizes is to be supported together by trapeze hangers, space hangers for smallest pipe size or install intermediate supports for smaller diameter pipe. D. Do not use wire or perforated metal to support piping, and do not support piping from other piping. E. Install hangers and supports complete with necessary inserts, bolts, rods, nuts, washers and other accessories. ©Raasch Associates, Inc. Project No. 3226 HANGERS AND SUPPORTS FOR HVAC SYSTEMS — Section 23 05 29 -3 F. Except as otherwise indicated for exposed continuous pipe runs, install hangers and supports of same type and style as installed for adjacent similar piping. G. Install anchors where indicated on the drawings and as detailed. H. Install hangers and supports to allow controlled movement for piping systems and to permit freedom of movement between pipe anchors, and to facilitate action of expansion joints, expansion loops, expansion bends and similar units. Install hangers and supports so that piping live and dead loading and stresses from movement will not be transmitted to connected equipment. Install hangers and supports to provide indicated pipe slopes. K. Insulated Piping: Install protective shields or saddles to prevent insulation vapor barrier damage and compression of insulation. 3.04 ADJUSTMENT OF HANGERS AND SUPPORTS A. Adjust hangers and supports and place grout as required under supports to bring piping to proper levels and elevations. END OF SECTION ©Raasch Associates, Inc. Project No. 3226 HANGERS AND SUPPORTS FOR HVAC SYSTEMS — Section 23 05 29 -4 DIVISION 23 - HVAC Section 23 05 93 - Testing, Adjusting, and Balancing PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and General Requirements of Contract, including General and Supplementary Conditions and Division 1 specification sections apply to Work of this Section. B. Extent of testing, adjusting, and balancing work is indicated by requirements of this section, and also by drawings and schedules, and is defined to include, but is not necessarily limited to: 1. Air distribution systems and associated equipment. C. The work consists of setting speed and volume (flow) adjusting facilities provided for systems, recording data, conducting tests, preparing and submitting reports, and recommending modifications to work as required by contract documents. D. Component types of testing, adjusting, and balancing specified in this section includes the following as applied to mechanical equipment: 1. Air - handling units. 2. Fans. 3. Ductwork systems. 1.02 QUALITY ASSURANCE A. Tester 1. A firm certified by National Environmental Balancing Bureau (NEBB) or Associated Air Balance Council (AABC) in those testing and balancing disciplines similar to those required for this project. B. Comply with American Society of Heating, Refrigerating and Air- Conditioning Engineers, Inc. (ASHRAE) recommendations pertaining to measurements, instruments and testing, adjusting and balancing, except as otherwise indicated and NEBB "Procedural Standards for Testing, Balancing and Adjusting of Environmental Systems ". 1.03 SUBMITTALS A. Submit certified test reports signed by Test and Balance Supervisor who perforined TAB work. B. Reports shall be on NEBB forms unless other forms have been approved by the Engineer prior to the start of testing. C. Include identification and types of instruments used and their most recent calibration date with submission of final test report. D. Include copies of certified test reports in maintenance manuals. 1.04 JOB CONDITIONS ©Raasch Associates, Inc. Project No. 3226 TESTING, ADJUSTING and BALANCING - Section 23 05 93 -1 A. Do not proceed with testing, adjusting, and balancing work until work has been completed and is operable. Ensure that there is no work still to be completed. B. Do not proceed until work scheduled for testing, adjusting, and balancing is clean and free from debris, dirt and discarded building materials. PART2- PRODUCTS 2.01 PATCHING MATERIALS A. Except as otherwise indicated, use same products as used by original Installer for patching holes in insulation, ductwork and housings which have been cut or drilled for test purposes, including access for test instruments, attaching jigs, and similar purposes. B. At Tester's option, plastic plugs with retainers may be used to patch drilled holes in ductwork and housings. PART 3 - EXECUTION 3.01 EXAMINATION A. Examine installed work and conditions under which testing is to be done to ensure that work has been completed, cleaned and is operable. Do not proceed with TAB work until unsatisfactory conditions have been corrected in manner acceptable to Tester. 3.02 TEST AND ADJUSTMENT A. Test, adjust and balance environmental systems and components, as indicated, in accordance with procedures outlined in applicable standards. B. Prepare report of test results, including instrumentation calibration reports, in fonnat recom rnended by applicable standards. C. Air side system balancing shall include but not be limited to the following procedures: 1. Test and adjust fan RPM to design requirements. 2. Test and record motor full load amperage. 3. Check all fans for correct rotation. 4. Test and record system static pressures, suction, discharge and external at all air handling equipment. 5. Test and record system static pressure suction and discharge at all coils. 6. Test and adjust system for design outside air and recirculated air quantities. 7. Adjust and record all main supply and return air ducts and zones to proper design CFM. S. Test and adjust each diffuser, grille and register to within 5% of design requirements. Record data and location. Use manufacturer's rating and calculations. 9. Adjust all diffusers and grilles to minimize drafts in all areas. 10. Test and record all air temperatures - supply, return, mixed, outside air including dry and wet bulb. D. Patch holes in insulation, ductwork and housings, which have been cut or drilled for test purposes, in manner recommended by original Installer. ©Raasch Associates, Inc. Project No. 3226 TESTING, ADJUSTING and BALANCING - Section 23 05 93 -2 E. Mark equipment settings, including damper control positions, fan speed control levers, and similar controls and devices, to show final settings at completion of TAB work. Provide markings with paint or other suitable permanent identification materials. F. Balancing contractor shall coordinate damper position settings with controls contractor to verify air flows and positions. G. Balancing contractor to work with temperature control contractor and HVAC contractor to verify correct operation of entire HVAC system, before submitting report. END SECTION ©Raasch Associates, Inc. Project No. 3226 TESTING, ADJUSTING and BALANCING - Section 23 05 93 -3 DIVISION 23 - HVAC Section 23 07 00 — Insulation for HVAC System PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and General Requirements of contract including General and Supplementary Conditions and Division 1 specification sections apply to work of this Section. B. Extent of HVAC system insulation specified in this section includes the following: 1. Ductwork System Insulation: a. Cold Ductwork. Dual Temperature Ductwork. 1.02 QUALITY ASSURANCE A. Installation shall meet the requirements of Wisconsin Department of Commerce Code Chapter 63 and Chapter 64. B. Manufacturer - Subject to compliance with requirements, provide products of one of the following: 1. Armstrong World Industries, Inc. 2. Certainteed Corp. 3. Knauf Fiberglass 4. Manville Corp. 5. Owens - Corning Fiberglass Corp. 6. Pittsburg Corning Corp. 7. Rubatex Corp. C. Installer - A firm with at least 3 years successful installation experience on projects with mechanical insulations similar to that required for this project. D. Flame /Smoke Ratings - Provide composite mechanical insulation (insulation, jackets, coverings, sealers, mastics and adhesives) with flame- spread rating of 25 or less, and smoke - developed rating of 50 or less, as tested by ANSI /ASTM E 84 (NFPA 255) method. 1.03 SUBMITTALS A. Product Data - Submit manufacturer's specifications and installation instructions for each type of mechanical insulation. Submit schedule showing manufacturer's product number, thickness, and furnished accessories for each mechanical system requiring insulation. B. Maintenance Data - Submit maintenance data and replacement material lists for each type of mechanical insulation. Include this data in maintenance manual. 1.04 DELIVERY, STORAGE AND HANDLING ©Raasch Associates, Inc. Project No. 3226 INSULATION FOR HVAC SYSTEMS — Section 23 07 00 -1 A. Deliver insulation, coverings, cements, adhesives, and coatings to site in containers with manufacturer's stamp or level, affixed showing fire hazard ratings of products. B. Protect insulation against dirt, water, and chemical and mechanical damage. Do not install damaged insulation; remove from project site. PART 2- PRODUCTS 2.01 DUCTWORK INSULATION MATERIALS A. Flexible Fiberglass Ductwork Insulation - ASTM C -553, Type II, K value 0.25 at 75° F. Owens Corning all service, faced, duct wrap, Type 150, 1.5 PCF. B. Flexible Unicellular Sheet Insulation -ASTM C534, Type II, K value 0.27 at 75 degrees F. Armafiex II. C. Rigid Fiberglass Ductwork Insulation - ASTM C612, Class 1, K value 0.23 at 75 Degrees F, 3 PCF, Owens - Corning 703. D. Vapor Barrier Material For Ductwork - FS HH -B -100; paper - backed aluminum -foil, except as otherwise indicated; strength and permeability rating equivalent to factory - applied vapor barriers on adjoining ductwork insulation. E. Ductwork Insulation Accessories - Provide staples, bands, wires, tape, anchors, corner angles and similar accessories as recornrnended by insulation manufacturer for applications indicated. F. Ductwork Insulation Compounds - Provide cements, adhesives, coatings, sealers, protective finishes and similar compounds as recommended by insulation manufacturer for applications indicated. PART 3 - EXECUTION 3.01 DUCTWORK SYSTEM INSULATION A. Cold Ductwork (below ambient temperature): 1. Application Requirements - Insulate the following cold ductwork: a. Outdoor air intake ductwork between air entrance and fan inlet or HVAC unit inlet. b. HVAC supply ductwork between fan discharge, or HVAC unit discharge, and room terminal outlet. 2. Insulate each ductwork system specified above with one of the following types and thicknesses of insulation: a. Insulation: Rigid fiberglass, 1 -1/2" thick, increase thickness to 2" in mechanical rooms. CORaasch Associates, Inc. Project No. INSULATION FOR HVAC SYSTEMS — Section 23 07 00 -2 B. Dual Temperature Ductwork: I. Application Requirements - Insulate the following dual temperature ductwork: a. Hot /cold supply ductwork between fan discharge, or HVAC unit discharge, and room terminal outlets. 2. Insulate each ductwork system specified above with one of the following types and thicknesses of insulation: a. Insulation: Rigid fiberglass; 1 -1/ 2" thick, 2" thick in mechanical room. 3.02 INSTALLATION OF DUCTWORK INSULATION A. Install insulation products in accordance with manufacturer's written instructions. B. Install insulation materials with smooth and even surfaces. C. Clean and dry ductwork prior to insulating. Butt insulation joints finnly together to ensure complete and tight fit over surfaces to be covered. D. Maintain integrity of vapor barrier on ductwork insulation, and protect it to prevent puncture and other damage. E. Extend ductwork insulation without interruption through walls, floors, and similar ductwork penetrations, except where otherwise indicated. F. Lined Ductwork - Except as otherwise indicated, omit insulation on ductwork where internal insulation or sound absorbing linings have been installed. G. Ductwork Exposed To Weather - Protect outdoor insulation from weather by installing protective jacketing. 3.03 PROTECTION AND REPLACEMENT A. Replace damaged insulation which cannot be repaired satisfactorily, including units with vapor barrier damage and moisture saturated units. B. Insulation Installer shall advise Contractor of required protection for insulation work during remainder of construction period, to avoid damage and deterioration. END SECTION ©Raasch Associates, Inc. Project No. INSULATION FOR HVAC SYSTEMS — Section 23 07 00 -3 DIVISION 23 - HVAC Section 23 09 23 — Direct Digital Control for HVAC Systems PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and General Requirements of contract including General and Supplementary Conditions and Division 1 specification sections apply to work of this Section. B. Extent of temperature control systems work is indicated by drawings and schedules, and by requirements of this Section. C. All control wiring necessary for equipment operation, except for wiring shown on electrical plans, is the work of this section. 1.01 QUALITY ASSURANCE A. Acceptable Manufacturers and Contractors Subject to compliance with requirements, provide electric- electronic control systems of one of the following: 1. Automated Logic. 2. Delta. 3. Johnson Controls. 4. Siemens. 5. TAC /CSI. B. Installer - Provide documentation to A/E showing experience in at least 3 other projects of similar size and scope. C. Electrical Standards - Provide electrical products which have been tested, listed and labeled by Underwriters' Laboratories (UL) and comply with NEMA standards. D. NEMA Compliance - Comply with NEMA standards pertaining to components and devices for electric- electronic temperature control systems. E. ASHRAE Standard Compliance - Comply with ASHRAE /ANSI Standard 135-2001 (or latest version) Data Communication Protocol for Building Automation and Control Systems (BACnet). F. Include at least 2 days coordination time with test and balance Contractor. 1.03 SUBMITTALS A. Product Data - Submit manufacturer's specifications for each control device furnished, including installation instructions and start-up instructions. B. Shop Drawings and Design Approval Documentation - At a minimum include: 1. System riser diagrams. 2. Schematic /wiring diagram for each control system. 3. Sequence of operation. 4. Logic diagrams for each control sequence... ©Raasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -1 5. Bill of Materials and Catalog data on each component used. 6. BAC net Protocol Implementation Conformance Statement (PICS) for each type of controller and operator interface used. 7. Valve and damper schedules. 8. Commissioning and acceptance checklist report format. C. Maintenance Data - Submit maintenance data and spare parts lists for each type of control device in maintenance manuals. At a minimum include: 1. Approved shop drawing submittal. 2. As -built system drawings. Provide in format compatible with AutoCAD 20010. Provide drawing files on optical storage disk and three hard copies on 11 x 17 paper. 3. Operator's manual. 4. Points list. 5. Logic diagrams. 6. Conduit routing diagrams and wiring diagrams. 7. Commissioning and acceptance checklists. 8. Trouble shooting and service guide. 9. Electronic copies of program files and software installed. 10. Training materials. 11. Warranty information. 1.04 DELIVERY, STORAGE, AND HANDLING A. Provide factory shipping cartons for each piece of equipment, and control device. Maintain cartons through shipping, storage and handling as required to prevent equipment damage, and to eliminate dirt and moisture from equipment. Store equipment and materials inside and protected from weather. PART 2- PRODUCTS 2.01 GENERAL A. Provide temperature control products in sizes and capacities indicated, consisting of valves, dampers, thermostats, sensors, controllers, and other components as required for complete installation. Except as otherwise indicated, provide manufacturer's standard temperature control system components as indicated by published product information, designed and constructed as recommended by manufacturer. B. System shall use the BACnet protocol for communication to the operator workstation or web server and for communication between control modules. Control products and devices shall comprise a BACnet internetwork. Schedules, setpoints, trends, and alarms specified in the sequence of operation shall be BACnet objects. 2.03 DAMPER ACTUATORS A. Electric damper actuators shall be fully proportioning, unless otherwise specified, and shall be of proper size to meet the power requirements B. Outdoor air, return, and exhaust air damper actuators shall fail safe in either a normally open or normally closed position in the event of control power failure. Dampers to the outside shall fail closed. ©Raasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -2 C. All damper operators shall be motorized, positive positioning type with external position indicators. Actuators shall be manually operable and shall allow field calibration. D. Actuators shall be mounted externally of ducts or air handling equipment wherever possible for ease of service and isolated from internal duct temperatures. 2.05 TEMPERATURE SENSORS A. Temperature Sensors shall be of the type and have accuracy ratings as indicated and /or required for the application and shall permit accuracy rating of within 1% of the temperature range of their intended use. Sensors shall be capable of being calibrated. 1. All duct sensors shall be electronic resistance type. 2. Sensors used for mixed air application shall be the averaging type of sufficient length to extend diagonally across the entire duct and have an accuracy of 1% 3. Duct sensors shall protrude into the air stream far enough to sense any temperature differences due to stratification, etc. 4. Outdoor air sensors shall have a minimum range of -20 °F to 110 °F and an accuracy of within 1 °F in this temperature range. 5. Room temperature sensors shall have an accuracy of 0.25 °F in the range of 45 °F to 95 °F. All room thermostats shall be solid state, electronic controllers utilizing resistance element and with communication port. The sensing element shall be mounted on printed circuit board. As a minimum, room sensors shall indicate set point temperature and actual temperature, and shall be programmable for temporary system occupancy override. 2.06 LOW TEMPERATURE PROTECTION THERMOSTATS A. Provide low- temperature protection thermostats of manual -reset type with sensing elements 8' -0" or 20' -0" in length. B. Provide thermostat designed to operate in response to coldest 1' -0" length of sensing element, regardless of temperature at other parts of element. C. Support element properly to cover entire unit width. Provide separate thermostats for each 25 sq. ft. of coil face area or fraction thereof. 2.08 PRESSURE SENSORS A. Differential Pressure and Pressure Sensors shall have a 4 -20 mA output proportional signal with provisions for field checking. Sensors shall withstand up to 150% of rated pressure, without damaging the device. Accuracy shall be within 2% of full scale. 2.10 TRANSMISSION SYSTEM A. The system shall utilize LAN architecture to allow all of the distributed control units to share data as well as to globalize alarms. The LAN shall be based on a peer -to -peer token passing technique. Network speed shall ensure that the maximum time to display or use changes of state or analog values shall be less than two seconds. B. Web server, workstation, and control network backbone shall communicate using Ethernet Data Link/Physical layer protocol and BACnet /IP addressing. ©Raasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -3 C. The LAN shall utilize a single pair of 18 ga. twisted, shielded cable for all network transmissions. The LAN shall provide for automatic reconfiguration if any station (distributed processing unit, unitary controller, etc.) is added or lost. Should the transmission cable be cut, the two sections shall reconfigure with no disruption to the system's operation and without any operator intervention. 2.11 BUILDING CONTROLLERS A. All points in the system shall be monitored and /or controlled through "intelligent" Building Controllers (BC's). Each BC in the system shall contain its own microprocessor and volatile and non - volatile memory. Application programming shall be retained for at least 72 hours in the event of power loss. Each BC in the system shall be a completely independent stand -alone "master" with its own hardware clock calendar and all firmware and software to maintain control on an independent basis. BC's shall substantially conform to the BACnet Building Controller (B -BC) device profile as specified in ASHRAE /ANSI 135. B. Each BC shall reside on or be connected to a BACnet network using Ethernet Data Link.Physical Layer protocol and BACnet/IP addressing. C. Each BC shall include the following capabilities: 1. Acquire, process, and transfer information to other BC's. 2. Accept, process, and execute commands from the other BC's or other input devices. 3. Record, evaluate, and report the changes of state and /or value that occur among points associated with the BC. If the operator station or transmission network fails, but the power to the BC does not, the BC shall continue to perform all control functions associated with the points connected to the network. 4. Ability to broadcast point data onto the network, thereby making that information available to all other BC's in the system. Each BC shall have the ability to transmit any or all I/O points as global points onto the network for use by other BC's and to utilizes data from other panels as part of its data base. To keep traffic on the network at a minimum, analog inputs shall be transmitted only after an operator specified change of value has occurred since the last broadcast value. 5. Create, delete, and support the following BACnet objects: a. Analog input, analog output, and analog value. b. Binary input, binary output, and binary value. c. Calendar. d. Device. e. Event enrollment. f. File. g. Loop (PID). h. Notification Class. i. Program. j. Schedule. k. Trend log. D. The following point types must be supported by the BC's. 1. Discrete /digital input (contact status). 2. Discrete /digital output. 3. Analog input (4 -20 mA or 1 -5 VDC with 12 -bit A/D conversion resolution minimum). 4. Analog output (4 -20mA and 0 -10 VDC with 8 -bit D/A resolution minimum). CORaasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -4 5. Pulse input capable of accepting 5 pulses /second and accumulating total. 6. Pulse output capable of producing a pulse anywhere between 0 -655 seconds in duration with 0.01 second resolution. E. Addressable points shall include analog inputs, analog outputs, pulse inputs, pulse outputs and discrete inputs /outputs, in sufficient quantities to perform the functions herein specified. F. Ability to download from or upload to a lap -top PC. 2.12 APPLICATION SPECIFIC CONTROLLER A. Each application specific controller shall operate as a stand -alone controller capable of performing its specified function independently of other controllers. Each unit shall be a microprocessor- based, multi - tasking, real time digital control. ASC's shall conform to the BACnet Application Specific Controller (B -ASC) device profile as specified in ASHRAE /ANSI 135. B. Each ASC shall reside on a BACnet network using the ARCNET or MS /TP Data Link/Physical layer protocol. C. As a minimum the application specific terminal unit controllers shall provide the following: 1. All algorithms for actual unit control shall be located in controller firmware to minimize the controller memory requirements. 2. Have all operating parameters stored in non volatile memory to assure control continuity after a power restoration. 3. Continue to provide all temperature control functions in the event that all communications with the network is lost. Units which default to a predetermined default value are unacceptable. 4. Provide for both PID and floating control logic to support modulating control of both dampers and reheat valves. 5. Setpoints for Both Heating and Cooling: a. Occupied Cooling Setpoint: Cooling setpoint is in effect during scheduled, or unscheduled occupied periods when there is a call for cooling (ie.,75F). b. Occupied Heating Setpoint: Heating setpoint is in effect during scheduled, or unscheduled occupied periods when there is a call for heating (ie.,70F). c. Unoccupied Cooling Setback: Cooling setpoint is in effect during scheduled or unscheduled unoccupied periods when there is call for cooling (ie.,85F). d. Unoccupied Heating Setback: Heating setpoint is in effect during scheduled or unscheduled unoccupied periods when there is call for heating (ie.,50F). e. Controller shall allow for selection of the room setpoint from a programmed value or a value from a space temperature sensor with adjustment dial. 2.13 ADVANCED APPLICATION CONTROLLER A. The digital AAC shall support direct unit mounting and may be supplied either factory mounted or for direct field installation. All outputs shall be supplied with form -C relays for field flexibility operating under software control for either modulating applications or two position discrete control. Each AAC shall conform to BACnet Advanced Application Controller (B -AAC) device profile as specified in ASHRAE /ANSI 135. ©Raasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -5 B. Each AAC shall reside on a BACnet network using the ARCNET or MS /TP Data Link/Physical layer protocol. C. As a minimum, the AAC's shall provide the following: 1. All algorithms for actual unit control shall be located in controller firmware to minimize the controller memory requirements. 2. Assure control continuity after a power restoration. Application programming shall be retained for at least 72 hours in the event of power loss. 3. Continue to provide all temperature control functions in the event that all communications with the network is lost. Units which default to a predetermined default value are unacceptable. 4. Provide for both PID and floating control logic to support modulating control of both dampers and reheat valves. 5. Setpoints for Both Heating and Cooling: a. Occupied Cooling Setpoint: Cooling setpoint is in effect during scheduled, or unscheduled occupied periods when there is a call for cooling (ie.,75F). b. Occupied Heating Setpoint: Heating setpoint is in effect during scheduled, or unscheduled occupied periods when there is a call for heating (ie.,70F). c. Unoccupied Cooling Setback: Cooling setpoint is in effect during scheduled or unscheduled unoccupied periods when there is call for cooling (ie.,85F). d. Unoccupied Heating Setback: Heating setpoint is in effect during scheduled or unscheduled unoccupied periods when there is call for heating (ie.,50F). e. Eight Universal Inputs (analog or discrete contact): The AAC shall be supplied with not less than eight (8) inputs which may be assigned in software for either analog or digital inputs. f. Eight Discrete Relay Outputs: The AAC shall be supplied with not less than eight (8) discrete outputs, complete with relays, which may be assigned in software for either digital or modulating control. 2.14 CENTRAL WORK STATION A. Provide software, control board, and other hardware required for installing building management system (BMS) into a computer provided by Owner. Give minimum system hardware and software requirements to Owner at time of bidding. B. Central work station will gather all data from Building Controllers. Work station shall be capable of communicating with any point on the network. The BMS software shall provide, as a minimum, the following functionality: 1. Real -time graphical viewing and control of the BAS Environment 2. Scheduling and override of building operations. 3. Collection and analysis of historical data. 4. Alarm reporting, routing, messaging, and logging for later retrieval. 5. Point database editing, storage and downloading of controller databases. 6. Reading status of points and changing setpoints. 7. Definition and construction of dynamic color graphic displays. 8. Function editing by users with appropriate assigned rights and privileges. C. Intranet /Internet Access 1. The BMS shall provide a web based graphical interface that allows users to access the BMS via the Internet, extranet, or intranet. ©Raasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -6 2. Graphics and information available at the BMS work station shall be available via web browser to users with appropriate assigned rights and privileges. 3. The web based interface shall provide the following functionality: a. Logon Screen allows access to approved users. b. Alarm display for current alarms to which the user has access. c. Display of BMS workstation graphics. d. Access to point details per user's defined access level rights. e. Override and command of points to which the user has rights. 4. The web server site licensing will allow 10 concurrent browser connections. 5. The Owner shall provide Internet connections, ISP services, firewalls or proxy servers as required to support the web access feature. D. Provide communication devices required to allow for remote trouble shooting of system. 2.15 LOCAL CONTROL PANELS A. Provide control panels with suitable brackets for either wall or floor mounting, for each system indicated. Locate panel as required. B. Provide standard steel cabinets as required to contain temperature controllers, relays, switches, and similar devices, except limit controllers and other devices excluded in sequence of operations. C. Provide full - enclosure, lockable cabinets, with manufacturer's standard finish. D. Mount required alarm lights, indicating devices and manual controls on face of panel. 2.17 ELECTRONIC AIRFLOW MEASUREMENT STATIONS AND TRANSMITTERS A. Air Flow Sensor - Factory calibrated sensor incorporating thermal dispersion technology and with prewired cable assembly. Unit construction shall be suitable for operation at airflow of up to 3,000 fpm over a temperature range of 30 to 160 degrees F, and accuracy shall be plus or minus 2 percent over a range of 0 to 3000 fpm scaled to air volume. Probe shall be suitable for internal duct or plenum mounting, duct insertion mounting, or standoff mounting. B. Transmitter - Each transmitter shall produce a linear, temperature compensated 4 to 40 mA DC, output corresponding to the required velocity pressure measurement. C. Manufacturer: Ebtron model SP probe, STA104 transmitter. 2.18 DUCT MOUNTED SMOKE DETECTORS A. Provide smoke detectors complying with NFPA 72E and with features listed: 1. Ionization type 2. Auxiliary SPDT relay contact. 3. Key- operated NORMAL -RESET -TEST switch. 4. Duct sampling tubes extending full width of duct. 5. Visual indication of detector actuation at mounting location. 6. Two -wire detector with common power supply and signal circuit. ©Raasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -7 PART 3 - EXECUTION 3.01 INSTALLATION D. Install system and materials in accordance with manufacturer's instructions and roughing - in drawings, and details on drawings. Install electrical work and use electrical products complying with requirements of applicable Division 26 sections of these specifications. Mount controllers at convenient locations and heights. E. Wiring - The term "wiring" is defined to include pulling of wire, installing conduit, installing raceways, and miscellaneous materials as required for mounting and connecting electric control devices. F. Wiring System 1. Install complete wiring system for temperature controls. a. Exposed Wiring: (1) Mechanical rooms and unfinished spaces: Install wiring in conduit. b. Concealed Wiring: Finished spaces. (1) Conceal wiring in cavities of new wall construction or above ceiling to the maximum extent possible. (2) High voltage: Install wiring in conduit. (3) Low voltage: Run wiring parallel or perpendicular to walls and surfaces. Support wiring at 10 foot minimum intervals. Run multiple conductors in common path where possible. (4) Install wiring within enclosures, and flexible conductors bridging cabinets and doors, neatly along hinge side, and protect against abrasion. Tie and support conductors neatly. 2. Number -code conductors, corresponding to schematic drawing numbering system, for future identification and servicing of control system. 3. Provide clearance between control wiring and power wiring per manufacturer's requirements, to prevent interference with control system. 4. Line voltage wiring for temperature control equipment shall be provided to each mechanical room under Division 26. Final connections to control panels and devices shall be work of this section. 3.02 CONTROL SEQUENCES A. Roof -Top Unit (RTU -1 thin RTU -15) 1. Roof -top system components include constant volume exhaust fan, return, relief and outdoor air dampers, filter section, direct expansion (DX) cooling coil, constant volume supply fan and gas fired heat exchanger. 2. The scheduling function of the BMS determines the occupied /unoccupied mode of the system and the building operating mode. In the occupied mode the roof -top unit runs and the outdoor air damper opens to maintain specified minimum quantity of outdoor air. 3. The unit controller maintains a discharge temperature through sequencing of the gas fired heat exchanger, modulating mixing dampers, and the DX cooling coil. The BMS shall survey all active zone temperatures and reset discharge temperatures at highest temperature that satisfies cooling requirements for all spaces served by the roof -top unit. 4. Economizer controls shall allow for the full use of outdoor air for cooling whenever outdoor air enthalpy is less than return air enthalpy. ©Raasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -8 a. Above 70 degrees F outdoor air temperature (adjustable), outdoor air damper will close to minimum position. b. The relief damper and exhaust fan shall modulate when the outdoor air damper opens beyond the minimum set -point in the economizer mode. 5. A low temperature protection thermostat shall shut the roof -top unit off if heating discharge temperature falls below 42 °F (adjustable). 6. Provide a duct mounted smoke detector to stop the roof -top unit and report an alarm upon detection of products of combustion. 3.03 MONITORING POINTS AND GRAPHICS A. Monitor points required to provide the control sequences listed. Allow for a future growth of 30 percent of each type of control point. B. Miscellaneous Monitoring Points 1. Provide controls and wiring to monitor the following items through the BMS: a. Office Temperatures. b. Toilet Temperatures. c. Entry temperatures. C. Provide graphics pages as outlined below: 1. Roof —Top Unit Systems 3.04 START -UP AND COMMISSIONING A. After completion of installation, calibrate equipment and verify transmission media operation before system is placed on -line. All testing, calibrating, adjusting, and final tests shall be completed by specially trained personnel in direct employ of the manufacturer. B. Notify Owner ten days in advance of start of conanissioning and testing to allow for Owner or Engineer review of testing procedures and testing. 3.05 TRAINING A. Provide two (2) full day training sessions, on site, for Owners' personnel. Training schedule shall be approved by Owner. END SECTION ©Raasch Associates, Inc. Project No. 3226 DIRECT DIGITAL CONTROL FOR HVAC SYSTEMS — Section 23 09 23 -9 DIVISION 23 - HVAC Section 23 11 00 —Facility Fuel Piping PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and General Requirements of Contract including General and Supplementary Conditions and Division 1 specification sections apply to Work of this Section. B. Extent of facility fuel piping system work is indicated on the project drawings, by requirements of this section, and includes the following: 1. Natural gas distribution system from gas meter to gas -fired equipment connections. 1.02 QUALITY ASSURANCE A. ANSI Code Compliance - Comply with applicable provisions of ANSI B31.2 "Fuel Gas Piping ". B. National Fuel Gas Code Compliance - Comply with applicable provisions of NFPA 54 (ANSI Z223.1) "National Fuel Gas Code ". C. Local Utility Compliance - Comply with requirements of the gas utility company serving the facility. 1.03 SUBMITTALS A. Product Data - Submit manufacturer's data for fuel gas piping systems materials and products. PART2- PRODUCTS 2.01 NATURAL GAS PIPING MATERIALS AND PRODUCTS A. Provide piping materials and factory - fabricated piping products of sizes, types, pressure ratings, and capacities as indicated. Provide sizes and types snatching piping and equipment connections; provide fittings of materials which match pipe materials used in natural gas piping systems. Where multiple material types or products are indicated, selection is Installer's option. 2.02 BASIC PIPE, TUBE, AND FITTINGS A. Provide pipe, tube, and fittings complying with Division 23 section 23 05 17 "Pipe, Tube, and Fittings for HVAC Systems ", in accordance with the following listing: B. Building Distribution and Regulator Vent Piping 1. Pipe Size 2" and Smaller Black steel pipe. a. Pipe Weight: Schedule 40. b. Fittings: Malleable iron threaded. ©Raasch Associates, Inc. Project No. 3226 FACILTY FUEL PIPING — Section 23 1100-1 2. Pipe size 2 -1/2" and Larger Black Steel Pipe. a. Pipe weight: Schedule 40. b. Fittings: Wrought -steel butt welding. C. Building Distribution Piping (Concealed) 1. Pipe Size 2" and Smaller Black steel pipe. a. Pipe Weight: Schedule 40. b. Fittings: Forged steel, Socket weld. 2. Pipe size 2 -1/2" and Larger Black Steel Pipe. a. Pipe weight: Schedule 40. b. Fittings: Wrought -steel butt welding. 2.03 BASIC PIPING SPECIALTIES A. Provide piping specialties complying with Division 23 section "Piping Specialties for HVAC Systems ", in accordance with the following listing: 1. Pipe escutcheons. 2. Pipe sleeves. 3. Sleeve seals. 2.04 BASIC SUPPORTS AND ANCHORS A. Provide supports and anchors complying with Division 23 section 23 05 19 "Hangers and Supports for HVAC Systems ", in accordance with the following listing: 1. Clevis hanger or band hangers for horizontal - piping. 2. Two -bolt riser clamps for vertical piping supports. 3. Beam clamps, concrete anchors and attachment plates for building attachments. 2.05 SPECIAL VALVES A. Shutoff Valves - 1. Plug Valves 2" and Smaller Cast iron body, threaded ends, nickel plated cast iron plug, 175 psi non -shock working pressure, lever or wrench actuator, UL listed for natural gas shut -off. 2. Ball Valves 2" and Smaller 600 psi WOG (non- shock), one -piece bronze body, threaded ends, full port chrome ball, teflon seat, blowout -proof stem, tee handle, UL listed for natural gas shut -off. 3. Plug _Valves 2 -1/2" and larger Cast iron body, flanged ends, nickel plated cast iron plug, 175 psi non -shock working pressure, lever actuator, UL listed for natural gas shut -off. 4. Manufacturer - Subject to compliance with requirements, provide gas shut -off valves of one of the following: a. DeZurik. b. Tufline. C. NIBCO. d. Homestead. e. Apollo. B. Gas Pressure Regulators 1. Provide regulators with cast aluminum body, corrosion resistant spring and internal components, self - aligning nitrile valve, nitrile diaphragm, threaded ends, ©Raasch Associates, Inc. Project No. 3226 FACILTY FUEL PIPING — Section 23 11 00 -2 10 psi maximum allowable continuous inlet pressure, and service temperature of - 20 to 150 deg F. 2. Regulators shall be designed for positive dead end lockup, with spring adjustment range of 4 to 12 inches WC, with a gas inlet pressure of 1.0 [2.0] [5.0] psig. 3. Manufacturer - Maxitrol (series 325), or Fischer. PART 3 - EXECUTION 3.01 INSTALLATION OF NATURAL GAS PIPING A. Install natural gas distribution piping in accordance with Division 23 section 23 05 17 "Pipe, Tube, and Fittings for HVAC Systems "; and in accordance with applicable codes and local utility company requirements. B. Use sealants on metal gas piping threads which are chemically resistant to natural gas. Use sealants sparingly, and apply to only male threads of metal joints. C. Remove cutting and threading burrs before assembling piping. D. Do not install defective piping or fittings. Do not use pipe with threads which are chipped, stripped or damaged. E. Plug each gas outlet, including valves, with threaded plug or cap immediately after installation and retain until continuing piping, or equipment connections are completed. F. Branch connections shall be made at the top or side of the gas main. G. Ground gas piping electrically and continuously within project, and bond tightly to grounding connection. H. Install drip -legs in gas piping where indicated, and where required by code or regulation. Install "Tee" fitting with bottom outlet plugged or capped, at bottom of pipe risers. Install piping with 1" drop in 60' pipe run (0.14 %) in direction of flow. K. All inaccessible gas piping shall be installed with welded joints. L. Where gas regulators are installed before equipment, install vent piping from vent outlet to exterior of building. Size vent pipe per regulator manufacturer's requirements. Terminate with screened, weather - proof, vent located per utility company's regulations. 3.02 GAS SERVICE A. Gas service has been arranged for with the utility company and fees paid for by the Owner. 3.03 INSTALLATION OF PIPING SPECIALTIES A. Install piping specialties in accordance with Division 23 section 23 05 19 "Piping Specialties for HVAC Systems ". ©Raasch Associates, Inc. Project No. 3226 FACILTY FUEL PIPING — Section 23 1100-3 3.04 INSTALLATION OF HANGERS AND SUPPORTS A. Install hangers and supports in accordance with Division 23 section 23 05 29 "Hangers and Supports for HVAC Systems ". 3.05 INSTALLATION OF VALVES A. Provide gas shutoff valves at connection to gas train for each gas -fired equipment item; and on risers and branches where indicated. B. Locate gas shutoff valves where easily accessible, and where they will be protected from possible injury. 3.06 EQUIPMENT CONNECTION A. Connect gas piping to each gas -fired equipment item, with drip leg and shutoff gas valve. Comply with equipment manufacturer's instructions. 3.07 PIPING TESTS A. Test natural gas piping in accordance with ANSI B31.2 or other recognized testing procedure. END SECTION ©Raasch Associates, Inc. Project No. 3226 FACILTY FUEL PIPING — Section 23 1100-4 DIVISION 23 - HVAC Section 23 31 00 - HVAC Ductwork and Casings PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and General Requirements of contract including General and Supplementary Conditions and Division 1 specification sections apply to work of this Section. B. Extent of ductwork is indicated on drawings and in schedules, and by requirements of this Section. C. Types of ductwork and casings required for project include the following: 1. Air conditioning supply and return air systems. 2. Fresh air supply systems. 3. Mechanical exhaust systems. 1.02 QUALITY ASSURANCE A. SMACNA Standards - Comply with the following SMACNA standards: 1. "HVAC Duct Construction Standards - Metal and Flexible" for fabrication and installation of ductwork. 2. HVAC Air Duct Leakage Test Manual. B. NFPA Compliance - Comply with the listed NFPA standards: 1. NFPA 90A "Standard For The Installation Of Air- Conditioning And Ventilating Systems ". 2. NFPA 90B "Standard For The Installation Of Warm Air Heating And Air - Conditioning Systems ". C. ASTM Standards - Materials and procedures for ductwork systems construction shall comply with the applicable listed ASTM standards: 1. ASTM A90 - Weight of Coating on Zinc - Coated (Galvanized) Iron or Steel Articles. 2. ASTM A 366 - Steel, Sheet, Carbon, Cold Rolled, Commercial Quality. 3. ASTM A 525 - General Requirements for Steel Sheet, Zinc- Coated (Galvanized) by the Hot -Dip Process. 4. ASTM A 527 - Steel Sheet, Zinc - Coated (Galvanized) by Hot -Dip Process, Lock Forming Quality 5. ASTM C 1071 - Thermal and Acoustical Insulation (Glass Fiber, Duct Lining Material). 6. ASTM E 84 - Surface Burning Characteristics of Building Materials. Flame spread index shall not exceed 25 and smoke - developed index shall not exceed 50. 7. ASTM E597 - Practice for Determining Single - Number Rating of Airborne Sound Isolation for Use in Multi -Unit Building Specifications ©Raasch Associates, Inc. Project No. 3226 HVAC DUCTWORK AND CASINGS — Section 23 31 00 -1 D. Underwriters Laboratories - UL 181 - Factory-Made Air Ducts and Connectors. 1.03 SUBMITTALS A. Product Data - Submit manufacturer's specifications on manufactured products, factory - fabricated ductwork, and ductwork systems materials used for work of this Section. B. Shop Drawings — Submit data for manufactured products and built up housing materials. Include dimensions, materials of construction, thermal and acoustical characteristics, pressure ratings, assembly and installation requirements, and appropriate identification. C. Record Drawings - At project closeout, submit record drawings of installed ductwork, duct accessories, and housings; in accordance with requirements of Division 1. 1.04 DELIVERY, STORAGE, AND HANDLING A. Protect shop - fabricated and factory- fabricated ductwork, accessories and purchased products from damage during shipping, storage and handling. Prevent end damage and prevent dirt and moisture from entering ducts and fittings. B. Where possible, store ductwork and housing panels inside and protect from weather. Where necessary to store outside, store above grade and enclose with waterproof wrapping. PART 2- PRODUCTS 2.01 DUCTWORK MATERIALS A. Exposed Ductwork Materials - Where ductwork is indicated to be exposed to view in occupied spaces, provide materials which are free from visual imperfections including pitting, seam marks, roller marks, oil canning, stains and discolorations, and other imperfections, including manufacturing residues or oils which would impair painting. B. Galvanized Steel Ductwork - Fabricate from galvanized sheet steel complying with ANSI /ASTM A 527, lockforrning quality, with ANSI /ASTM A 525, G90 zinc coating; mill phosphatized for exposed locations. 2.02 MISCELLANEOUS DUCTWORK MATERIALS A. Duct Liner 1. Rigid fiberglass liner board, complying with ASTM C 1071, Type II. 2. "K" value per ASTM C 518 of 0.23 at 75 degrees F. 3. Maximum rated velocity: 5000 FPM. 4. Thickness: 1 inch (unless noted or detailed). 5. Liner Adhesive - Comply with requirements of ASTM C 916. CRaasch Associates, Inc. Project No. 3226 HVAC DUCTWORK AND CASINGS — Section 23 31 00 -2 6. Liner Fasteners - Comply with SMACNA "HVAC Duct Construction Standards - Metal and Flexible. B. Duct Sealant - Non - hardening, non - migrating mastic or liquid elastic sealant. Sealants shall be water resistive, fire resistive, and compatible with mating surfaces. C. Ductwork Support Materials 1. Hot - dipped galvanized fasteners, anchors, hanger rods, straps, trim and angles shall be used to support ductwork. Hanger Rod: ASTM A36; threaded both ends, threaded one end, or continuously threaded. 2. Support aluminum ductwork with aluminum support materials or with materials electrolytically isolated from the ductwork. D. Fasteners Rivets, bolts, or sheet metal screws. 2.03 DUCTWORK FABRICATION A. Fabricate ductwork of gauges and reinforcement complying with SMACNA "Duct Construction Standards - Metal and Flexible" Latest Edition. Provide duct material, gages, reinforcing, and sealing for operating pressures indicated. B. Fabricate duct fittings to match adjoining ducts, and to comply with duct requirements as applicable to fittings. Except as otherwise indicated, fabricate elbows with centerline radius 1.5 times the associated duct width; and fabricate to include turning vanes in elbows where shorter radius is necessary. Provide airfoil turning vanes in 18 x 18 inch or larger ductwork and acoustic lined ductwork. Limit angular tapers to 45° for contracting tapers and 30° for expanding tapers. C. Fabricate continuously welded round and oval duct fittings two gages heavier than duct gages indicated in SMACNA Standard. Joints shall be minimum 4 inch cemented slip joint, continuous welded, or spot welded and sealed. Prime coat welded joints. D. Provide standard 45 degree lateral wye or 90 degree conical tee fittings at branch connections to round duct mains. Provide 45 degree entry or conical fittings at branch connections to rectangular duct mains. E. Fabricate ductwork with accessories installed during fabrication to the greatest extent possible. Refer to Division 23 section 23 33 00 "Air Duct Accessories" for accessory requirements. F. Fabricate ductwork with duct liner in each section of duct where indicated. Laminate liner to internal surfaces of duct in accordance with instructions by manufacturer of lining and adhesive, and fasten with mechanical fasteners. 2.05 TRANSVERSE JOINT DUCT CONNECTION SYSTEMS ©Raasch Associates, Inc. Project No. 3226 HVAC DUCTWORK AND CASINGS — Section 23 31 00 -3 A. Rectangular, round or oval ductwork systems using proprietary slide -on flanges as manufactured by Ductmate may be used at contractor's option. Rectangular ductwork with a side dimensions 42 inches or larger shall be joined with Ductmate system flanges. B. Transverse joints shall be constructed per SMACNA, non - proprietary, T -22 reinforcement standards, type "Y rigidity class. System includes 20 gauge roll formed slide -on flange with integral sealant, gasketing, cleats, and corner clips. C. Rectangular transverse joint duct connection systems utilizing proprietary formed on flanges (formed from the ends of the duct walls) may be used at contractor's option. Formed on flange joints shall be limited to ductwork systems constructed for 2 inch maximum static pressure (positive or negative) PART 3 - EXECUTION 3.01 INSTALLATION OF DUCTWORK A. Fabricate and Install ductwork in accordance with SMACNA HVAC Duct Construction Standards - Metal and Flexible. Construct ductwork systems to the pressure class listed in the Ductwork Application Schedule, located in this specification section, or as listed on the drawings. B. Seal ductwork joints, seams, and duct wall penetrations in accordance with the SMACNA recommended seal class for the listed pressure class of the ductwork systems. C. Locate ductwork runs vertically and horizontally wherever possible. Install ductwork so that usable space or equipment access is not obstructed. Hold ducts close to walls, overhead construction, columns, and other structural and permanent enclosure elements of building. D. Verify dimensions at the site, making field measurements and drawings necessary for fabrication and erection. Check plans showing work of other trades and consult with Architect/Engineer to resolve interferences. E. Duct sizes indicated on the drawings are inside clear dimensions. F. No variation of duct configuration or sizes permitted except by prior approval or Architect /Engineer. Size round ducts installed in place of rectangular ducts in accordance with ASHRAE table of equivalent rectangular and round ducts. G. Provide frames constructed of angles or channels for coils, filters, dampers or other devices to be installed in the duct systems. Make all connections to such equipment, including equipment furnished by others. Install sheet metal close -off fabrications to prevent air bypass around channel mounted equipment. Fasten close -off sheets to interior plenum or casing wall and equipment support channels. H. Provide supplementary auxiliary steel members required to support ductwork. Attach to ©Raasch Associates, Inc. Project No. 3226 HVAC DUCTWORK AND CASINGS — Section 23 3100-4 building structure. Attach steel members by welding or clamping. L Install all motor operated dampers and connect to or install all duct - mounted equipment furnished under other Division 23 sections or other trades. Branch ductwork shall be provided for all air outlets and inlets and shall be constructed with sufficient length to contain the grille plus any damper, in fully open position, without obstructing main duct air flow. K. Round or oval ductwork exposed in occupied finished areas shall be free from dents and scratches, and duct sealant applied shall have a smooth, finished appearance. L. Provide openings in ductwork where required to accommodate thermometers and controllers. Provide pitot tube openings where required for testing of systems, complete with metal can with spring device or screw to ensure against air leakage. Where openings are provided in insulated ductwork, install insulation material inside a metal ring. M. Where ductwork penetrates interior partitions, floors, and exterior walls, pack the annular space with insulation and conceal the space between opening and duct or duct insulation with sheet metal flanges of same gauge as duct. Where ducts pass through fire -rated floors, walls or partitions, provide fire stopping between duct and opening. N. Locate ducts with sufficient space around equipment to allow normal operating and maintenance activities. O. Do not install ductwork through dedicated electrical or elevator equipment rooms or spaces unless the ductwork is serving the room or space. P. Use double nuts and lock washers on threaded rod supports. Q. Connect diffusers to ductwork directly or with 5 feet maximum length of flexible duct. R. Connect flexible ducts to metal ducts with stainless steel draw bands and per ductwork manufacturer's written instructions. 3.03 CLEANING AND PROTECTION A. Clean ductwork internally, unit -by -unit as it is installed, of dust and debris. Clean external surfaces of foreign substances which might cause corrosive deterioration of metal or, where ductwork is to be painted, might interfere with painting or cause paint deterioration. B. At ends of ducts which are not connected to equipment or any distribution devices at time of ductwork installation, provide temporary closure of polyethylene film or other covering which will prevent entrance of dust and debris until time connections are to be completed. 3.04 DUCTWORK APPLICATION SCHEDULE ©Raasch Associates, Inc. Project No. 3226 HVAC DUCTWORK AND CASINGS — Section 23 31 00 -5 Air System Material Pressure Class Constant Volume Supply Return and Relief General Exhaust Galvanized Steel, Aluminum Galvanized Steel, Aluminum Galvanized Steel, Aluminum 4.0 inch 4.0 inch 2.0 inch END SECTION ©Raasch Associates, Inc. Project No. 3226 HVAC DUCTWORK AND CASINGS — Section 23 3100-6 DIVISION 23 - HVAC Section 23 33 00 — Air Duct Accessories PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and General Requirements of contract including General and Supplementary Conditions and Division 1 specification sections apply to Work of this Section. B. Extent of duct accessories work is indicated on drawings and in schedules, and by requirements of this section C. Types of duct accessories required for project include the following: Manual Dampers. Control Dampers. Duct Hardware. 4. Turning Vanes. 5. Duct Access Doors. 6. Flexible Connections. 1.02 QUALITY ASSURANCE A. SMACNA Standards - Comply with applicable portions of Sheet Metal and Air Conditioning Contractor's National Association ( SMACNA) "HVAC Duct Construction Standards - Metal and Flexible" B. AMCA Standards - Construct, test, and label louvers and dampers in accordance with AMCA Standard 500 -L and 500 -D "Test Methods for Louvers and Dampers ". C. UL Standards 1. Construct, test, and label fire dampers in accordance with Underwriters Laboratories (UL) Standard 555 "Fire Dampers and Ceiling Dampers ". 2. Construct flexible connections of materials rated and tested per UL standard 214 - Tests for Flame Propagation of Fabrics and Films. D. NFPA Standards - Comply with applicable provisions of ANSI/NFPA 90A "Air Conditioning and Ventilating Systems ", pertaining to installation of duct accessories. 1.03 SUBMITTALS A. Product Data - Submit manufacturer's specifications for each type of duct accessory, including dimensions, capacities, and materials of construction; and installation instructions. B. Shop Drawings - Submit assembly -type shop drawings for each type of duct accessory showing interfacing requirements with ductwork, and method of fastening or support. ©Raasch Associates, Inc. Project No. 3226 AIR DUCT ACCESSORIES — Section 23 33 00 -1 C. Maintenance Data - Submit manufacturer's maintenance data including parts lists for each type of duct accessory. Include this data in Maintenance Manual. PART 2 - PRODUCTS 2.01 MANUAL DAMPERS A. Provide dampers of single blade type or multiblade type, constructed in accordance with SMACNA Standards, except as specified below. B. Damper Construction: 1. Dampers shall be of channel frame construction. 2. Provide molded synthetic bearings for all dampers used in 3" or less pressure class ductwork systems. Provide bronze bearings and seals for dampers used in greater than 3" pressure class ductwork systems. 3. Provide standoff brackets for dampers used with insulated ductwork systems. 4. Multiblade dampers shall be of opposed blade design. C. Manufacturers - Subject to compliance with requirements, provide dampers of one of the following: American Warning, Arrow, Cesco, Greenheck, Ruskin, Vent Products. 2.02 CONTROL DAMPERS A. Provide control dampers where shown on the plans and as required to perform the specified temperature control functions. B. Use only factory fabricated dampers with replaceable resilient blade seals, stainless steel jamb seals and with entire assembly suitable for the maximum temperature and air velocities encountered in the system. Dampers shall have frames of not less than 16 gauge galvanized steel or 12 gauge extruded aluminum. Blades shall be of airfoil design, 20 gauge galvanized steel for double thickness, or 14 gauge aluminum, with steel rod, bronze bearings. Maximum allowable blade width is 8 inches. Linkages shall be concealed in the damper frame. Use zinc plated steel linkage hardware. C. All dampers for shut -off or isolation service shall have leakage not exceed 3 cfm/square foot at 1" water gauge, and 7 cfm/square foot at 4" water gauge. D. Dampers used for mixing of airstreams shall be parallel blade type, sized for air velocity of 1800 to 2000 fpm. Dampers used for throttling or modulating applications other than air stream mixing shall be opposed blade type. Two position dampers may be parallel or opposed blade type. E. Damper actuators shall be provided under specification section 23 09 23. F. Maximum damper width is 48 inches; where required width exceeds 48 inches, use multiple dampers. Minimum size for duct mounted dampers is 90% of duct size. G. Manufacturer /Model: 1. Control dampers shall be Ruskin model CD -50 low leakage dampers. ©Raasch Associates, Inc. Project No. 3226 AIR DUCT ACCESSORIES — Section 23 33 00 -2 Equal products of one of the following shall be acceptable: American Warning, Arrow, Cesco, Greenheck, Vent Products. 2.03 DUCT HARDWARE A. Quadrant Locks Provide for each manual damper, quadrant lock device on one end of shaft; and end bearing plate on other end for damper lengths over 12 ". Provide extended quadrant locks and end extended bearing plates for externally insulated ductwork. B. Manufacturers - Subject to compliance with requirements provide duct hardware of one of the following: 1. Ventfabrics, Inc. 2. Young Regulator Co. 3. Damper manufacturer's standard or optional hardware. 2.04 TURNING VANES A. Construct turning vanes and runners for square elbows in accordance with SMACNA HVAC Duct Construction Standards. B. Construct turning vanes for short radius elbows in accordance with SMACNA HVAC Duct Construction Standards, Fig. 2 -5 and Fig. 2 -6. C. Manufacturer - Subject to compliance with requirements, provide turning vanes of one of the following: Aero Dyne, Anemostat, Hart & Cooley. 2.05 DUCT ACCESS DOORS A. Construct of same or greater gauge as ductwork served, provide insulated doors for insulated ductwork. B. Provide flush frames for uninsulated ductwork, extended frame for externally insulated duct. C. Provide one side hinged, other side with 1 handle -type latch for doors 12" high and smaller, 2 handle -type latches for larger doors. D. Manufacturers - Subject to compliance with requirements provide duct access doors of one of the following: 1. Ruskin Mfg. Co. 2. Ventfabrics, Inc. 2.06 FLEXIBLE CONNECTIONS A. Flexible ductwork connection material shall be UL 214 listed, fire retardant, and shall meet the requirements of NFPA 90A. B. Construct flexible connections of 3 inch wide neoprene- coated flameproof fabric crimped ©Raasch Associates, Inc. Project No. 3226 AIR DUCT ACCESSORIES — Section 23 33 00 -3 into duct flanges for attachment to duct and equipment. Make air tight joint. 1. Material for indoor applications shall be neoprene coated glass fiber with a nominal weight of 30 ounces per square yard. 2. Material for outdoor applications shall be hypalon coated glass fiber with a nominal weight of 26 ounces per square yard. 3. Material for corrosive environments or fume exhaust applications shall be Teflon coated glass fiber with a nominal weight of 14 ounces per square yard. C. Provide adequate joint flexibility to allow for thermal, axial, transverse, and torsional movement, and also capable of absorbing vibrations of connected equipment. D. Manufacturers - Subject to compliance with requirements provide flexible connections of one of the following: L Ventfabrics PART 3 - EXECUTION 3.01 INSPECTION A. Examine areas and conditions under which duct accessories will be installed. Do not proceed with work until unsatisfactory conditions have been corrected. 3.02 INSTALLATION A. Install duct accessories in accordance with manufacturer's installation instructions, with applicable portions of details of construction as shown in SMACNA standards. B. Install manual volume dampers in each branch duct and for each grille, register, or diffuser as far away from the outlet as possible while still maintaining accessibility to the damper. Install so there is no flutter or vibration of the damper blades. C. Install control dampers in locations indicated on the drawings, as detailed, and according to the manufacturer's instructions. Install blank -off plates or transitions where required for proper mixing of airstreams in mixing plenums. Provide adequate operating clearance and access to the operator. Install an access door adjacent to each control damper for inspection and maintenance. D. Install flexible duct connections to rotating or vibrating equipment, including air handling units, fans, or other motorized equipment in accordance with SMACNA standards. E. Coordinate with other work, including ductwork, as necessary to interface installation of duct accessories properly with other work. F. ACCESS DOORS 1. Install access doors where specified, indicated on the drawings, and in locations where maintenance, service, cleaning or inspection is required. Examples include, but are not limited to motorized dampers, - -smoke detectors, fan bearings, heating ©Raasch Associates, Inc. Project No. 3226 AIR DUCT ACCESSORIES — Section 23 33 00 -4 and cooling coils, filters, valves, and control devices needing periodic maintenance. Size and numbers of duct access doors to be sufficient to perform the intended service. Minimum access door size shall be 8 x 8 inch size for hand access, 18 x 18 inch size for shoulder access, or other size as indicated. Install access doors on both inlet and outlet sides of duct coils. Install access doors to open against system air pressure, with latches operable from either side, except outside only where duct is too small for person to enter. G. TURNING VANES 1. Install turning vanes in square, rectangular, or short radius 90 degree elbows in supply, return, relief, and exhaust air systems, and elsewhere as indicated. 2. Install turning vanes in accordance with SMACNA standards and /or manufacturer's recommendations. 3. Install double wall, airfoil, 2 inch radius vanes in ducts with vane runner length 18" or greater and air velocity less than 2000 fpm. Install double wall, airfoil, 4- 1/2 inch radius vanes in ducts with vane runner length 18" or greater and air velocity 2000 fpm or greater. 4. If duct size changes in a mitered elbow, use single wall type vanes with a trailing edge extension. If duct size changes in a radius elbow or if short radius elbows must be used, install sheet metal turning vanes in accordance with SMACNA Figure 2 -5 and Figure 2 -6. 3.03 FIELD QUALITY CONTROL A. Operate installed duct accessories to demonstrate compliance with requirements. B. Test for air leakage while system is operating. C. Repair or replace faulty accessories, as required to obtain proper operation and leakproof performance. END SECTION ©Raasch Associates, Inc. Project No. 3226 AIR DUCT ACCESSORIES — Section 23 33 00 -5 DIVISION 23 - HVAC Section 23 34 00 — HVAC Fans PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and General Requirements of Contract including General and Supplementary Conditions and Division 1 specification sections apply to Work of this Section. B. Extent of propeller fan work required by this section is indicated on drawings and schedules, and by requirements of this section. C. Types of fans required for project include the following: Destratification Fans 1.02 QUALITY ASSURANCE A. AMCA Compliance - Provide fans which have been tested and rated in accordance with AMCA standards, and bear AMCA Certified Ratings Seal. B. UL Compliance - Provide fans which are designed, manufactured, and tested in accordance with UL. C. NEMA Compliance - Provide motors and electrical accessories complying with NEMA standards. 1.03 SUBMITTALS A. Product Data - Submit manufacturer's technical data for propeller destratification fans, including specifications, capacity ratings, dimensions, weights, materials, accessories furnished, and installation instructions. B. Shop Drawings - Submit assembly -type shop drawings showing unit dimensions, construction details, methods of assembly of components, and field connection details. C. Wiring Diagrams - Submit manufacturer's electrical requirements for power supply wiring to propeller fans. Submit manufacturer's ladder -type wiring diagrams for interlock and control wiring. Clearly differentiate between portions of wiring that are factory- installed and portions to be field- installed. D. Maintenance Data - Submit maintenance data and parts list for each type of propeller fan, accessory, and control. Include this data and product data in maintenance manual; in accordance with requirements of Division 1. PART 2 - PRODUCTS 2.01 DESTRATIFICATION FANS ©Raasch Associates, Inc. Project No.3226 HVAC FANS — Section 23 34 00 -1 A. Manufacturer - Subject to compliance with requirements, provide propeller fans of one of the following: Leading Edge, Emerson - Chromalox, Envirofan, Hunter, or approved equal. B. U.L. listed, all metal construction, baked enamel finish with factory standard color. Motors to be totally enclosed, impedance protected, single speed, of split capacitor design with permanently lubricated ball bearings. PART 3 - EXECUTION 3.01 INSPECTION A. Examine areas and conditions under which destratification fans are to be installed. Do not proceed with work until unsatisfactory conditions have been corrected. 3.02 INSTALLATION OF DESTRATIFICATION FANS A. Contractor shall balance blade assembly of destratification fans after installation to assure stable operation. B. Install fans in accordance with manufacturer's installation instructions. C. Coordinate fan work with work of ceilings as necessary for proper interfacing. D. Furnish copy of manufacturer's wiring diagram submittal to Electrical Installer. 1. Verify that electrical wiring installation is in accordance with manufacturer's submittal. 2. Verify proper rotation direction of fan. Do not proceed with equipment start -up until wiring installation is acceptable to equipment installer. 3.03 FIELD QUALITY CONTROL A. After installation of fans has been completed, test each fan to demonstrate proper operation of units at performance requirements specified. When possible, field correct malfunctioning units, retest to demonstrate compliance. Replace units which cannot be satisfactorily corrected. END SECTION ©Raasch Associates, Inc. Project No.3226 HVAC FANS — Section 23 34 00 -2 DIVISION 23 - HVAC Section 23 74 00 — Packaged Outdoor HVAC Equipment PART 1 - GENERAL 1.01 DESCRIPTION OF WORK A. Drawings and General Requirements of Contract including General and Supplementary Conditions and Division 1 specification sections apply to Work of this Section. B. Extent of packaged outdoor HVAC equipment work required by this section is indicated on drawings and schedules, and by requirements of this section. C. Types of packaged outdoor HVAC equipment specified in this section include the following: 1. Single -zone cooling and gas -fired heating. D. Refer to Division 26 sections for the following; not work of this Section: 1. Power supply wiring from power source to power connection on packaged outdoor HVAC equipment. Including starters, disconnects, and required electrical devices, except where specified as furnished, or factory- installed, by manufacturer. 2. Interlock wiring between electrically - operated equipment units; and between equipment and field- installed control devices. 3. Interlock wiring specified as factory - installed is work of this section. E. Provide the following electrical work as work of this section complying with requirements of Division 26 sections: 1. Control wiring between field- installed controls, indicating devices, and unit control panels. 2. Control wiring specified as work of another Division 23 section is work of that section. F. Refer to other Division 23 sections for piping and ductwork required external to packaged outdoor HVAC equipment for installation; not work of this section. 1.02 QUALITY ASSURANCE A. AHRI Compliance - Test and rate packaged outdoor HVAC equipment under 65,000 btu /hr capacity in accordance with ANSI /AHRI 210/240 -2008: Performance Rating of Unitary Air- Conditioning & Air- Source Heat Pump Equipment. B. AHRI Compliance - Test and rate packaged outdoor HVAC equipment greater than 65,000 btu /hr capacity in accordance with ANSI /AHRI 340/360 -2007: Performance Rating of Commercial and Industrial Unitary Air - Conditioning and Heat Pump Equipment. C. AHRI Compliance - Sound test and rate packaged outdoor HVAC equipment in ©Raasch Associates, Inc. Project No. 3226 PACKAGED, GAS FIRED, MAKE -UP AIR UNITS — Section 23 74 23 -1 accordance with AHRI 270: Sound Rating of Outdoor Unitary Equipment, and provide Certified Rating Seal. D. ASHRAE Compliance - Construct refrigerating systems of packaged outdoor HVAC equipment in accordance with ASHRAE 15 "Safety Code for Mechanical Refrigeration ". E. ASHRAE - Provide Energy Efficiency Ratio (EER) of packaged outdoor HVAC equipment not less than prescribed by ASHRAE 90A "Energy Conservation in New Building Design ". F. UL Compliance - Provide packaged outdoor HVAC equipment that is UL tested and certified. 1.03 SUBMITTALS A. Product Data - Submit manufacturer's technical product data, including rated capacities of selected model clearly indicated, weights, furnished specialties and accessories; and installation and start-up instructions. B. Shop Drawings - Submit manufacturer's assembly -type shop drawings indicating dimensions, weight loadings, required clearances, and methods of assembly of components. C. Wiring Dia rg ams - Submit manufacturer's electrical requirements for power supply wiring for packaged outdoor HVAC equipment. Submit manufacturer's ladder -type wiring diagrams for interlock and control wiring. Clearly differentiate between portions of wiring that are factory- installed and portions to be field - installed. D. Maintenance Data - Submit maintenance data and parts list for packaged outdoor HVAC equipment, controls, and accessories; including "trouble- shooting" maintenance guide. Include this data and product data in maintenance manual; in accordance with requirements of Division 1. 1.04 PRODUCT DELIVERY, STORAGE, AND HANDLING A. Handle packaged outdoor HVAC equipment and components carefully to prevent damage. Do not install damaged packaged outdoor HVAC equipment or components. B. Store packaged outdoor HVAC equipment and components in clean dry place. Protect from weather, dirt, fumes, water, construction debris, and physical damage. C. Comply with Manufacturer's rigging and installation instructions for unloading packaged outdoor HVAC equipment, and moving them to final location. 1.05 SPECIAL PROJECT WARRANTY A. Warranty On Compressor and Heat Exchanger - Provide written warranty, signed by manufacturer, agreeing to replace /repair, within warranty period, compressors and /or heat exchangers with inadequate and defective materials and workmanship, including leakage, breakage, improper assembly, or failure to perform as required; provided manufacturer's ORaasch Associates, Inc. Project No. 3226 PACKAGED, GAS FIRED, MAKE -UP AIR UNITS — Section 23 74 23 -2 instructions for handling, installing, protecting, and maintaining units have been adhered to during warranty period. Replacement is limited to component replacement only, and does not include labor for removal and reinstallation. B. Warranty Period - 5 years from date of substantial completion. PART2- PRODUCTS 2.01 SINGLE -ZONE COOLING AND GAS -FIRED HEATING A. General - Provide factory- assembled and tested outdoor units as indicated, designed for roof or slab mounting, consisting of compressors, condensers, evaporator coils, condenser and evaporator fans, refrigeration and temperature controls, filters, and dampers. Provide capacities and electrical characteristics as scheduled. B. Casing - Provide manufacturer's standard casing construction, corrosion protection coating, and exterior finish. Provide access doors for inspection and access to internal parts. Insulate casing with 1" thick minimum thermal insulation. Provide knockouts for electrical and piping connections. Provide condensate drain connection. C. Evaporator Fans - Provide double inlet, forward- curved, centrifugal, belt - driven fans with adjustable sheaves and permanently lubricated motor bearings. D. Condenser Fans - Provide propeller -type, direct - driven fans with permanently lubricated bearings. Fans shall discharge vertically. Motors shall totally enclosed type. E. Coils: 1. For evaporator and condenser, provide non - ferrous construction with aluminum plate fins mechanically bonded to seamless, internally grooved, copper tubes; with brazed tubing joints. 2. Coils shall be leak tested at 150 psig and pressure tested at 450 psig. 3. Dual compressor models shall have face -split type evaporator coil with circuit one on the bottom. F. Compressors - Provide serviceable, fully hermetic compressors, in accordance with manufacturer's published technical data. Provide vibration isolators and crankcase heaters. G. Refrigerant Components: Each refrigerant circuit shall include: 1. Thermostatic expansion valve (TXV) with removable power element. 2. Filter driers. 3. Gage port and connections on suction and discharge. H. Filter Section: 1. Standard filter section shall consist of factory- installed 2 -inch thick throwaway fiberglass filters, of 30% efficiency, pleated, and shall be of commercially available sizes. 1. Safety Controls: ©Raasch Associates, Inc. Project No. 3226 PACKAGED, GAS FIRED, MAKE -UP AIR UNITS — Section 23 74 23 -3 I . Provide a solid -state compressor protector which provides anti -cycle reset capability at the space thermostat if any of the following standard safety devices trip and shut off the compressor: a. Low pressure cutout. b. High pressure cutout. C. Compressor lockout protection for either internal or external overload. d. Evaporator freeze protection. 2. Heating section shall be provided with the following minimum protections: a. Redundant gas valve. b. Flame rollout switch. C. Flame proving controls. d. High limit cutout. e. Forced draft proving switch/motor speed sensor. Heating Section: 1. Heat Exchanger: a. Provide formed and seamed aluminized steel heat exchanger. The heat exchanger shall be of the tubular- section type constructed of a minimum of 20 -gage steel coated with a nominal 1.2 mil aluminum- silicone alloy for corrosion resistance. b. Optional stainless steel heat exchanger shall be available. The heat exchanger shall be constructed of a minimum of 20 gauge type 409 stainless steel. 2. Induced -draft combustion type with direct -spark ignition system and redundant main gas valve with 2 -stage capability. 3. Burners shall be of the in -shot type constructed of aluminum- coated steel. 4. All gas piping shall enter the unit at a single location. K. Accessories - Provide the following accessories as indicated or scheduled: 1. Full Perimeter Roof Curbs (Vertical): a. Formed of 18 -gauge or heavier galvanized steel with wood nailer strip and shall be capable of supporting entire unit weight. b. Permits installing and securing ductwork to curb prior to mounting unit on the curb. C. Provide insulated roof curb, constructed in accordance with NRCA Standards. d. Curbs shall be custom fabricated to fit standing seam or rib panel roof configuration. Curbs shall have integral conforming notches to assure water tight seal. Coordinate selection with roofing manufacturer. e. Curb assembly to be a minimum of 14 inches high. Curbs shall be provided with continuously welded and mitered corners, 3 -pound density insulation filling, integral deck mounting flange and galvanized steel counter flashing. Integrated Economizer: a. Economizer shall be furnished and installed complete with return air dampers and outside air dampers. b. Differential Enthalpy Sensor: By Temperature control Contractor. C. Low - leakage dampers ride in UL approved gears. ©Raasch Associates, Inc. Project No. 3226 PACKAGED, GAS FIRED, MAKE -UP AIR UNITS — Section 23 74 23 -4 d. Capable of introducing up to 100% outdoor air for minimum ventilation as well as free cooling. e. Damper actuator: By Temperature Control Contractor. f. Economizer outdoor hood shall be pre - painted. g. Economizer shall be available for field or factory installation. 3. Power Exhaust: Package shall include an exhaust (centrifugal style) fan, direct - drive motor, and damper for vertical flow units with economizer to control over - pressurization of building. 4. Low Ambient Control: Provide head pressure control, designed to operate at temperatures down to 30 °F. 5. Thennostats and Subbases: See section 23 09 23. 6. Convenience Outlet: Shall be factory- installed and internally- mounted with an externally accessible 115 -v, 15 amp. GFI, female receptacle with hinged cover. A step down transformer shall be included. 7. Hail Guard /Condenser Coil Grille: Shielding to protect the condenser coil from hail, flying debris, and damage by large objects without increasing unit clearances. 8. Return Air Smoke Detector: By Temperature Control Contractor. L. Manufacturer - Subject to compliance with requirements, provide packaged outdoor HVAC equipment of one of the following: 1. Carrier. 2. McQuay. 3. Trane. 4. York. 5. Lennox. PART 3 - EXECUTION 3.01 INSPECTION A. Examine areas and conditions under which packaged outdoor HVAC equipment are to be installed. Do not proceed with work until unsatisfactory conditions have been corrected in manner acceptable to Installer. 3.02 INSTALLATION OF PACKAGED OUTDOOR HVAC EQUIPMENT A. General - Install packaged outdoor HVAC equipment in accordance with manufacturer's installation instructions. Install units plumb and level, firmly anchored in locations indicated, and maintain manufacturer's recommended clearances. B. Support - Install units on roof curb, in accordance with National Roofing Contractor's Association (NRCA) installation recommendations. C. Electrical Wiring - Install electrical devices furnished by manufacturer but not specified to be factory- mounted. Furnish copy of manufacturer's wiring diagram submittal to Electrical Installer. D. Verify that electrical wiring installation is in accordance with manufacturer's submittal and ©Raasch Associates, Inc. Project No. 3226 PACKAGED, GAS FIRED, MAKE -UP AIR UNITS — Section 23 74 23 -5 installation requirements of Division 26 sections. Do not proceed with equipment start -up until wiring installation is acceptable to equipment installer. E. Ductwork - Refer to Division 23 section HVAC Ductwork and Casings. Connect supply and return ducts to unit with flexible duct connections. Provide transitions to exactly match unit duct connection sizes. F. Gas Piping - Refer to Division 23 section Facility Fuel Piping. Connect gas piping to unit gas train with union, shutoff cock, and drip leg. G. Start -Up - Start -up packaged outdoor HVAC equipment, in accordance with manufacturer's start-up instructions. Test controls and demonstrate compliance with requirements. Replace damaged or malfunctioning controls and equipment. H. Balancing of packaged outdoor HVAC equipment is specified in Division 23 section Testing, Adjusting, and Balancing; not work of this section. 3.03 GROUNDING A. Provide positive equipment ground for packaged outdoor HVAC equipment components. 3.04 TRAINING OF OWNER'S PERSONNEL A. Provide services of manufacturer's technical representative for 1 -half day to instruct Owner's personnel in operation and maintenance of packaged outdoor HVAC equipment. B. Schedule training with Owner, provide at least 7 -day notice to Contractor and A/E of training date. 3.05 SPARE PARTS A. General - Furnish to Owner, with receipt, the following spare parts for packaged outdoor HVAC equipment: 1. (1) set of matched fan belts for each belt- driven fan. 2. (1) set filters for each unit. END SECTION ©Raasch Associates, Inc. Project No. 3226 PACKAGED, GAS FIRED, MAKE -UP AIR UNITS — Section 23 74 23 -6 DIVISION 26 - ELECTRICAL Section 26 05 00 — Common Work Results for Electrical PART 1 - GENERAL 1.01 SECTION INCLUDES A. Basic Electrical Requirements specifically applicable to Division 26, 27, and 28 Sections, in addition to Division 1 - General Requirements. 1.02 RELATED WORK A. Division 1 - General Requirements. 1.03 REFERENCES A. ANSI Standards. B. IEEE Standards. C. NFPA Standards. D. NECA Standards. E. OSHA Standards. 1.04 REGULATORY REQUIREMENTS A. ANSI /NFPA 70 - National Electrical Code. B. ANSI /IEEE C2 - National Electrical Safety Code. C. Conform to all applicable federal, state and local building, electrical and energy codes. D. Electrical: Conform to NFPA 70 and NFPA 70E. E. Obtain all applicable permits and request inspections from authority having jurisdiction. F. In areas where Drawings and Specifications are in conflict, the more stringent and expensive equipment and methods shall apply. 1.05 SUBMITTALS A. Submit under provisions of Division 1. B. Proposed Products List: Include Products specified in the following Sections: 1. Section 26 27 28 - Disconnect Switches. 2. All equipment called out on the Drawings by trade name or catalog number. C. Submit shop drawings and product data grouped to include complete submittals of related systems, products, and accessories in a single submittal. D. Mark dimensions and values in units to match those specified. ©Raasch Associates Inc. Project No. 3226 COMMON WORK RESULTS for ELECTRICAL — Section 26 05 00 -1 1.06 QUALIFICATIONS A. The installer of any specified equipment shall have installed similar electrical equipment for a minimum period of five years. When requested by the Engineer, an acceptable list of installations with similar equipment shall be provided demonstrating compliance with this requirement. B. The installer of any specified equipment shall comply with all safety requirements specified in NFPA 70E as a minimum including, but not limited to the requirements for working on and near exposed, energized conductors and circuit parts. Additionally, all Winnebago County electrical safety policies shall be observed. Installer shall provide all personal protective equipment (PPE), insulated tools, insulating barriers, signs and barricades required to comply with NFPA 70E and Winnebago County electrical safety policies. Winnebago County electrical safety equipment shall not be used by the Electrical Contractor or any sub- contractors. When requested by the Engineer, an acceptable list of employee training in NFPA 70E requirements and available PPE shall be provided demonstrating compliance with this requirement. 1.07 DELIVERY, STORAGE AND HANDLING A. Store and protect products under provisions of Division 1 and per manufacturer's instructions. B. Deliver products to site. C. Store and protect products. 1.08 OPERATION AND MAINTENANCE DATA A. Submit under provisions of Division 1. B. Include replacement parts list for all specified equipment. C. Include manufacturer - recommended maintenance schedule for all specified equipment. 1.09 WARRANTY A. Installer shall warrant specified installation free from defects in materials and workmanship for the lesser of one year from the date of installation or eighteen months from the date of purchase. 1.10 PROJECT CONDITIONS A. Install Work in locations shown on Drawings, unless prevented by Project conditions. B. Show proposed rearrangement of Work to meet Project conditions, including changes to Work specified in other Sections. Obtain permission of Engineer before proceeding. 1.11 PROJECT RECORD DOCUMENTS A. Accurately record any work that deviates from work shown on the Drawings. END OF SECTION ©Raasch Associates Inc. Project No. 3226 COMMON WORK RESULTS for ELECTRICAL — Section 26 05 00 -2 DIVISION 26 - ELECTRICAL Section 26 05 01 - Electrical Scope of Work PART 1 - GENERAL 1.01 SECTION INCLUDES A. The electrical contractor's work shall include, but not be limited to the following: 1. All new disconnect switches for new HVAC equipment. 2. Disconnecting power feeds to existing HVAC equipment scheduled for removal. 3. All new wiring from new disconnect switches to new HVAC equipment, including conduit and terminations. 4. All new fuses and circuit breakers required as a result of the HVAC equipment changes. B. The Electrical Contractor shall visit the site of construction to familiarize himself with site and existing conditions so as to become fully informed as to the extent and character of the work and its relationship to work of other trades and existing facilities. C. If any errors or omissions appear in Drawings, Specifications, or other documents, bidding Contractor shall notify Engineer prior to submitting bid. Should conflict occur in or between drawings and specifications, bidding contractor is deemed to have estimated more expensive way of doing work, unless he shall have asked for and obtained written decision (addendum) before submission of Proposal as to which method or materials will be required. 1.02 WORK NOT INCLUDED A. Low voltage (less than 120 volts) control wiring for HVAC equipment by mechanical contractor. END OF SECTION ©Raasch Associates, Inc. Project No. 3226 ELECTRICAL SCOPE OF WORK - Section 26 05 01 -1 DIVISION 16 - ELECTRICAL Section 26 05 19 — Low Voltage Electrical Power Conductors and Cables PART 1 - GENERAL 1.01 SECTION INCLUDES A. Building wire and cable. B. Wiring connectors and connections. 1.02 RELATED WORK A. Section 26 05 33 — Raceway and Boxes. 1.03 REFERENCES A. ANSI/NFPA 70 - National Electrical Code. 1.04 REGULATORY REQUIREMENTS A. Conform to requirements of ANSI/NFPA 70. B. Furnish products listed and classified by Underwriters Laboratories, Inc. as suitable for purpose specified and shown. 1.05 SUBMITTALS A. None required for the equipment specified under this Section. 1.06 QUALIFICATIONS A. Manufacturer: Company specializing in manufacturing products specified in this Section with minimum five years experience. 1.07 DELIVERY, STORAGE, AND HANDLING A. Deliver, store, protect, and handle products to site under provisions of Division 1. B. Accept wire on site. Inspect for damage. C. Protect wire from corrosion and entrance of debris by storing above grade. Provide appropriate covering. D. Protect wire from sunlight. 1.08 OPERATION AND MAINTENANCE DATA A. None required for the equipment specified under this Section. 1.09 WARRANTY A. None required for the equipment specified under this Section. ©Raasch Associates, Inc. Project No. 3226 Low Voltage Electrical Power Conductors & Cables - Section 26 05 19 -1 1.10 PROJECT CONDITIONS A. Verify that field measurements are as shown on Drawings. B. Wire and cable routing shown on Drawings is approximate unless dimensioned. Route wire and cable as required to meet Project Conditions. C. Where wire and cable routing is not shown, and destination only is indicated, determine exact routing and lengths required. D. Coordinate Work under provisions of Division 1. E. Determine required separation between cable and other work. F. Determine cable routing to avoid interference with other work. G. Coordinate equipment, duct, piping, conduit, tray and cable installation with Plumbing and Mechanical Contractors. Assure proper clearances and needed room to install respective systems. 1.11 PROJECT RECORD DOCUMENTS A. Submit under provisions of Division 1. B. Accurately record size, type and load served of all wires in conduits larger than 2 inches. C. Accurately record size, type and load served of all wires in cable trays. D. Accurately record size, type and load served of all wires in conduits installed underground. Indicate use of wire (i.e. power, telephone, control, etc.) PART 2- PRODUCTS 2.01 BUILDING WIRE AND CABLE — SINGLE CONDUCTORS A. Description: Single conductor insulated wire. B. Conductor: Copper. C. Insulation Voltage Rating: 600 volts. D. Feeders and Branch Circuits Larger than 6 AWG: Copper stranded conductor, 600 volt insulation, XHHW, 90° C. E. Feeders and Branch Circuits 6 AWG and Smaller: Copper stranded conductor, 600 volt insulation, THWN -2, 90° C. PART 3 - EXECUTION 3.01 FACTORY TESTING A. None required beyond factory standard tests for the equipment specified under this Section. ©Raasch Associates, Inc. Project No. 3226 Low Voltage Electrical Power Conductors & Cables - Section 26 05 19 -2 3.02 INSTALLATION A. Verify that interior of building has been protected from weather. B. Verify that mechanical work likely to damage wire and cable has been completed. C. Completely and thoroughly swab raceway before installing wire. D. Run all wiring in conduit unless cable tray is specifically called out on the drawings. E. Install products in accordance with manufacturer's instructions. F. Use conductor not smaller than 12 AWG for power and lighting circuits. G. Size all conductors in all circuits to insure voltage drop of less than 3 %. H. Pull all conductors into raceway at same time I. Use suitable wire pulling lubricant for building wire 4 AWG and larger J. Protect exposed cable from damage. K. Use suitable cable fittings and connectors. L. Neatly train and lace wiring inside boxes, equipment, and panelboards. M. Clean conductor surfaces before installing lugs and connectors. N. Make splices, taps, and tenninations to carry full ampacity of conductors with no perceptible temperature rise. O. Use split bolt connectors for copper conductor splices and taps, 6 AWG and larger. Tape uninsulated conductors and connector with electrical tape to 150 percent of insulation rating of conductor. P. Use solderless pressure connectors with insulating covers for copper conductor splices and taps, 8 AWG and smaller. Q. Do not share neutrals or grounds between circuits. Run separate, full -sized neutrals and grounds for each circuit. R. Conductor color coding: 277/480V Phase A - Brown Phase B - Orange Phase C - Yellow Neutral - Gray Ground - Green 120/208V or 120/240V Phase A - Black Phase B - Red Phase C - Blue Neutral - White Ground - Green S. Identify cables in all junction and pull boxes with voltage, circuit, and load. ©Raasch Associates, Inc. Project No. 3226 Low Voltage Electrical Power Conductors & Cables - Section 26 05 19 -3 3.03 INTERFACE WITH OTHER PRODUCTS A. Identify wire and cable under provisions of Section 26 05 53. B. Identify each conductor with its circuit number or other designation indicated on Drawings. 3.04 FIELD QUALITY CONTROL A. Inspect wire and cable for physical damage and proper connection. B. Torque test conductor connections and terminations to manufacturer's recommended values. C. Perforrn continuity test on all power equipment branch circuit conductors. Verify proper phasing connections. END OF SECTION ©Raasch Associates, Inc. Project No. 3226 Low Voltage Electrical Power Conductors & Cables - Section 26 05 19 -4 DIVISION 26 - ELECTRICAL Section 26 05 26 - Grounding and Bonding PART 1 - GENERAL 1.01 SECTION INCLUDES A. Equipment Grounding Conductors. B. Bonding. 1.02 RELATED WORK A. Section 26 05 33 — Raceway and Boxes. B. Section 26 05 19 — Low Voltage Electrical Power Conductors and Cable C. Motors. D. Electrical equipment. E. Process / Mechanical equipment. 1.03 REFERENCES A. ANSI/NFPA 70 - National Electrical Code. 1.04 REGULATORY REQUIREMENTS A. Conform to requirements of ANSI /NFPA 70. B. Furnish products listed and classified by Underwriters Laboratories, Inc. as suitable for purpose specified and shown. 1.05 SUBMITTALS A. None required for the equipment specified under this Section. 1.06 QUALIFICATIONS A. Manufacturer: Company specializing in manufacturing products specified in this Section with minimum five years experience. 1.07 DELIVERY, STORAGE, AND HANDLING A. Deliver, store, protect, and handle products to site under provisions of Division 1. B. Accept grounding equipment on site. Inspect for damage. C. Protect grounding equipment from corrosion and entrance of debris by storing above grade. Provide appropriate covering. ©Raasch Associates, Inc. Project No. 3226 GROUNDING AND BONDING - Section 26 05 26 -1 1.08 OPERATION AND MAINTENANCE DATA A. None required for the equipment specified under this Section. 1.09 WARRANTY A. None required for the equipment specified under this Section. 1.10 PROJECT CONDITIONS A. Verify that field measurements are as shown on Drawings. B. Coordinate Work under provisions of Division 1. C. Detennine required separation between grounding equipment and other work. D. Determine grounding equipment locations to avoid interference with other work. E. Coordinate equipment, duct, piping, conduit and cable installation with Plumbing and Mechanical Contractors. Assure proper clearances and needed room to install respective systems. 1.11 PROJECT RECORD DOCUMENTS A. Submit under provisions of Division 1. B. Accurately record size, type and load served of all wires in conduits larger than 2 inches. C. Accurately record size, type and load served of all wires in conduits installed underground. Indicate use of wire (i.e. power, telephone, control, etc.) PART2- PRODUCTS 2.01 WIRE A. Material: Copper. B. Equipment Grounding Conductor: Size to meet NFPA 70 requirements. PART 3 - EXECUTION 3.01 FACTORY TESTING A. None required beyond factory standard tests for the equipment specified under this Section. 3.02 INSTALLATION A. Install Products in accordance with manufacturer's instructions. B. Provide bonding to meet Regulatory Requirements. C. Equipment Grounding Conductor: Provide separate, insulated conductor for each feeder and branch circuit. Terminate each end on suitable lug, bus, or bushing. Do not use conduit or tray as only grounding path. ©Raasch Associates, Inc. Project No. 3226 GROUNDING AND BONDING - Section 26 05 26 -2 D. Provide separate, insulated neutral and ground conductors for each feeder and branch circuit. Do not share neutral or ground conductors between circuits. 3.03 INTERFACE WITH OTHER PRODUCTS A. Identify wire and cable under provisions of Section 26 05 53. B. Identify each conductor with its circuit number or other designation indicated on Drawings. 3.04 FIELD QUALITY CONTROL A. Inspect grounding and bonding system conductors and connections for tightness and proper installation. END OF SECTION ©Raasch Associates, Inc. Project No. 3226 GROUNDING AND BONDING - Section 26 05 26 -3 DIVISION 26 - ELECTRICAL Section 26 05 29 — Supporting Devices PART 1- GENERAL 1.01 SECTION INCLUDES A. Conduit and equipment supports. B. Fastening hardware. 1.02 RELATED WORK A. Section 26 05 33 — Raceway and Boxes. 1.03 REFERENCES A. ANSI/NFPA 70 - National Electrical Code. 1.04 REGULATORY REQUIREMENTS A. Conform to requirements of ANSI/NFPA 70. B. Furnish products listed and classified by Underwriters Laboratories, Inc. as suitable for purpose specified and shown. 1.05 SUBMITTALS A. None required for the equipment specified under this Section. 1.06 QUALIFICATIONS A. Manufacturer: Company specializing in manufacturing products specified in this Section with minimum five years experience. 1.07 DELIVERY, STORAGE, AND HANDLING A. Deliver, store, protect, and handle products to site under provisions of Division 1. B. Accept equipment on site. Inspect for damage. C. Protect equipment from corrosion and entrance of debris by storing above grade. Provide appropriate covering. 1.08 OPERATION AND MAINTENANCE DATA A. None required for the equipment specified under this Section. 1.09 WARRANTY A. None required for the equipment specified under this Section. 1.10 PROJECT CONDITIONS A. Verify that field measurements are as shown on Drawings. ©Raasch Associates, Inc. Project No. 3226 SUPPORTING DEVICES - Section 26 05 29 -1 B. Coordinate Work under provisions of Division 1. C. Determine required separation between equipment and other work, avoid interference. D. Coordinate equipment, duct, piping, conduit and cable installation with Plumbing and Mechanical Contractors. Assure proper clearances and needed room to install respective systems. 1.11 PROJECT RECORD DOCUMENTS A. None required for the equipment specified under this Section. PART 2- PRODUCTS 2.01 MATERIAL A. Support Channel: Hot -dip Galvanized for wet or damp locations; painted steel for interior or dry locations. All field cuts shall be touched up with matching finish to inhibit rusting. B. Hardware: Corrosion resistant. C. Anchorage and Structural Attachment Components: a. Strength as defined in reports by ICBO Evaluation Service or other agency acceptable to authority having jurisdiction. Strength in tension and shear of components used shall be at least two times the maximum seismic forces to which they will be subjected. b. Concrete and Masonry Anchor Bolts and Studs: Steel expansion type. C. Concrete Inserts: Steel channel type. d. Through Bolts: Structural type, hex head, high strength. Comply with ASTM A 325. e. Welding Lugs: Comply with MSS- SP -69, Type 57. f. Beam Clamps for Steel Beams and Joists: Double sided. g. Bushings for Floor- Mounted Equipment Anchors: Neoprene units designed for seismically rated rigid equipment mountings and matched to the type and size of anchor bolts and studs used. h. Bushing Assemblies for Wall- Mounted Equipment Anchorage: Assemblies of neoprene elements and steel sleeves designed for seismically rated rigid equipment mountings and matched to the type and size of attachment devices used. PART 3 - EXECUTION 3.01 INSTALLATION A. Fasten hanger rods, conduit clamps, and outlet and junction boxes to building structure using expansion anchors or beam clamps. B. Use toggle bolts or hollow wall fasteners in hollow masonry, plaster, or gypsum board partitions and walls; expansion anchors or preset inserts in solid masonry walls; self - drilling anchors or expansion anchor on concrete surfaces; sheet metal screws in sheet metal studs; and wood screws in wood construction. C. Do not fasten supports to piping, ductwork, mechanical equipment, or conduit. D. Do not use power- actuated anchors. ©Raasch Associates, Inc. Project No. 3226 SUPPORTING DEVICES - Section 26 05 29 -2 E. Do not drill structural steel members. F. Fabricate supports from structural steel or steel channel, rigidly welded or bolted to present a neat appearance. Use hexagon head bolts with spring lock washers under all nuts. G. In wet locations install free - standing electrical equipment on concrete pads. In dry locations, install free - standing electrical equipment on steel base channels. H. Install surface - mounted cabinets and panelboards with minimum of four anchors. I. Bridge studs top and bottom with channels to support flush - mounted cabinets and panelboards in stud walls. Support systems shall be adequate for weight of equipment and conduit, including wiring, which they carry. END OF SECTION ©Raasch Associates, Inc. Project No. 3226 SUPPORTING DEVICES - Section 26 05 29 -3 DIVISION 26 - ELECTRICAL Section 26 05 33 — Raceway and Boxes PART 1 - GENERAL 1.01 SECTION INCLUDES A. Liquidtight flexible metal conduit. B. Fittings and conduit bodies. C. Wall and ceiling outlet boxes. D. Pull and junction boxes. 1.02 RELATED WORK A. Section 26 05 29 — Hangars and Supports for Electrical Systems. B. Section 26 05 53 — Electrical Identification. C. Section 26 27 02 — Equipment Wiring Systems. 1.03 REFERENCES A. ANSI/NEMA FB 1 - Fittings, Cast Metal Boxes, and Conduit Bodies for Conduit and Cable Assemblies. B. ANSUNEMA OS 1 — Sheet -Steel Outlet Boxes, Device Boxes, Covers and Box Supports. C. ANSUNFPA 70 - National Electrical Code. D. NECA "Standard of Installation ". E. NEMA 250 — Enclosures for Electrical Equipment (1000 Volts Maximum). 1.04 REGULATORY REQUIREMENTS A. Conform to requirements of ANSI/NFPA 70. B. Furnish products listed and classified by Underwriters Laboratories, Inc. as suitable for purpose specified and shown. 1.05 SUBMITTALS A. None required for the equipment specified under this Section. 1.06 QUALIFICATIONS A. The manufacturer of this equipment shall have produced similar electrical equipment for a minimum period of five years. ©Raasch Associates, Inc. Project No. 3226 RACEWAY AND BOXES - Section 26 05 33 -1 1.07 DELIVERY, STORAGE, AND HANDLING A. Deliver, store, protect, and handle products to site under provisions of Division 1. B. Accept conduit and boxes on site. Inspect for damage. C. Protect conduit and boxes from corrosion and entrance of debris by storing above grade. Provide appropriate covering. 1.08 OPERATION AND MAINTENANCE DATA A. None required for the equipment specified under this Section. 1.09 WARRANTY A. None required for the equipment specified under this Section. 1.10 PROJECT CONDITIONS A. Verify that field measurements are as shown on Drawings. B. Verify routing and termination locations of conduit prior to rough -in. C. Conduit routing and box locations are shown on Drawings in approximate locations unless dimensioned. Route and locate as required to complete wiring system. D. Where boxes are not shown, and destination only is indicated, detennine exact size and location required. E. Determine required separation between boxes and other work. F. Determine box locations to avoid interference with other work. G. Coordinate equipment, duct, piping, conduit and cable installation with Plumbing and Mechanical Contractors. Assure proper clearances and needed room to install respective systems. 1.11 PROJECT RECORD DOCUMENTS A. Submit under provisions of Division 1. B. Accurately record actual routing of conduits larger than 2 inches. C. Accurately record actual routing of all conduits installed underground. Indicate routing on drawing, dimension off permanent structures, indicate use of conduit (i.e. power, telephone, control, etc.), indicate size of conduit, number and size of wires, and indicate load served. D. Accurately record actual locations and mounting heights of outlet, pull, and junction boxes. PART 2- PRODUCTS 2.01 CONDUIT REQUIREMENTS A. Minimum Size: 3/4 inch unless otherwise specified. B. Outdoor Locations, Above Grade: Use Liquidtight flexible metal conduit. ©Raasch Associates, Inc. Project No. 3226 RACEWAY AND BOXES - Section 26 05 33 -2 2.02 LIQUIDTIGHT FLEXIBLE CONDUIT A. Description: Interlocked steel construction with PVC jacket. B. Fittings: ANSI/NEMA FB 1. 2.03 PULL AND JUNCTION BOXES A. Sheet Metal Boxes: NEMA OS 1; galvanized steel. B. Surface- Mounted Cast Metal Box: NEMA 250, Type 4; flat - flanged, surface - mounted junction box. 1. Material: Cast aluminum. 2. Cover: Furnish with ground flange, neoprene gasket, and stainless steel cover screws. PART 3 - EXECUTION 3.01 FACTORY TESTING A. None required beyond factory standard tests for the equipment specified under this Section. 3.02 INSTALLATION A. Install conduit in accordance with NECA "Standard of Installation." B. Arrange supports to prevent misalignment during wiring installation. C. Support conduit using coated steel or malleable iron straps, lay -in adjustable hangers, clevis hangers, and split hangers. D. Group related conduits; support using conduit rack. Construct rack using steel channel; provide space on each for 25 percent additional conduits. E. Fasten conduit supports to building structure and surfaces under provisions of Section 26 05 29. F. Do not support conduit with wire or perforated pipe straps. Remove wire used for temporary supports. G. Do not attach conduit to ceiling support wires. H. Arrange conduit to maintain headroom and present neat appearance. I. Route exposed conduit parallel and perpendicular to walls. J. Route conduit under slab from point -to- point. K. Do not install conduits in slab. L. Maintain adequate clearance between conduit, piping, and ductwork. M. Maintain 12 inch clearance between conduit and surfaces with temperatures exceeding 104 degrees F. (40 degrees Q. N. Cut conduit square using saw or pipe cutter; de -burr cut ends. O. Bring conduit to shoulder of fittings; fasten securely. ©Raasch Associates, Inc. Project No. 3226 RACEWAY AND BOXES - Section 26 05 33 -3 P. Use conduit hubs to fasten conduit to sheet metal boxes in damp and wet locations and to cast boxes. Q. Install no more than equivalent of three 90- degree bends between boxes. Use conduit bodies to make sharp changes in direction, as around beams. R. Avoid moisture traps; provide junction box with drain fitting at low points in conduit system. S. Provide suitable fittings to accommodate expansion and deflection where conduit crosses, control and expansion joints. T. Provide suitable pull string in each empty conduit except sleeves and nipples. U. Use suitable caps to protect installed conduit against entrance of dirt and moisture. V. Ground and bond conduit. W. Identify conduit under provisions of Section 26 05 53. X. Conduit Size: ANSI/NFPA 70 or as shown on drawings, whichever is larger. Y. Install electrical boxes as shown on Drawings, and as required for splices, taps, wire pulling, equipment connections and compliance with regulatory requirements. Z. Install electrical boxes to maintain headroom and to present neat mechanical appearance. AA. Install boxes to preserve fire resistance rating of partitions and other elements, using materials and methods under the provisions of Division 1. BB. Align adjacent wall - mounted outlet boxes for switches, thermostats, and similar devices with each other. CC. Use adjustable steel channel fasteners for hung ceiling outlet box. DD. Do not fasten boxes to ceiling support wires. EE. Support boxes independently of conduit, except cast box that is connected to two rigid metal conduits both supported within 12 inches of box. FF. Use cast outlet box in exterior locations and wet locations. GG. Large Pull Boxes: Boxes larger than 100 cubic inches in volume or 12 inches in any dimension. 1. Interior Dry Locations: Use hinged enclosure, supported by provisions of Section 26 05 29. 2. Other Locations: Use surface - mounted cast metal box. 3.03 INTERFACE WITH OTHER PRODUCTS A. Install conduit to preserve fire resistance rating of partitions and other elements, using materials and methods under the provisions of Division 1. B. Route conduit through roof openings for piping and ductwork or through suitable roof jack with pitch pocket. Coordinate location with roofing installation specified. ©Raasch Associates, Inc. Project No. 3226 RACEWAY AND BOXES - Section 26 05 33 -4 C. Coordinate all installation with other Divisions. Resolve all areas of interference before proceeding with work. D. Coordinate installation of outlet box for products furnished under other divisions. E. Coordinate locations and sizes of required access doors. F. Coordinate equipment, duct, piping, conduit and cable installation with Plumbing and Mechanical Contractors. Assure proper clearances and needed room to install respective systems. G. Install knockout closure in unused box openings. H. Panelboards shall not be used as pull boxes or junction boxes. 3.04 FIELD QUALITY CONTROL A. Inspect conduit and boxes for physical damage and proper connection. END OF SECTION ©Raasch Associates, Inc. Project No. 3226 RACEWAY AND BOXES - Section 26 05 33 -5 W NNEBAGO Sheet Title G001 TITLE SHEET COUNTY ROOF PLAN M001 E M101 E'; ��e�O����l M102 MAIN HALL HVAC PLAN C �NTED fir.... -LLI:- dc5 rAurs ,I Pnrr,t Rd y I L ''felin" bmra Re ID 21 a WittrM Ave n �o- A ¢ R e Y a W Sunrtyvlevl Rd w CG R0 Y n3 Tb P rinnebaw Wn H »grz Menial Health �`a r I _ ^ Insemne R 7& t well Rd 45 41 cn -South '.Asylum Bay: � T8 c d5 �, o � m m T6 I.aka 5•�nu• _ w Murder A, 45 E FA d-k Ave M;iJllifiK31 "' �nll C.)LS..kp Tt x r a& CO Rd - Udler y @aV d1 'p7 5 l)nIVPfSily ®f OShk0Sh E Irving P.xe r "' "" W�consin - P;,rk P,� UshkoM Gnn+I+LS 'J ^lJl:_n A wlYZel Ave . _ ^,_:ge• ��:.: ,w.,^ tih ,.e V�rw ; • LOCATION �U SCALE- NTS Sheet List Table Sheet Number Sheet Title G001 TITLE SHEET A101 ROOF PLAN M001 HVAC DEMOLITION SHEET M101 WEST AND SOUTH WING HVAC PLANS M102 MAIN HALL HVAC PLAN M601 HVAC DETAILS AND SCHEDULES E101 DEMOLITION ONE LINE DIAGRAM E102 ELECTRICAL DEMOLITION PLAN E201 INSTALLATION ONE LINE DIAGRAM E202 ELECTRICAL INSTALLATION PLAN E301 SCHEDULES AND ELECTRICAL SYMBOLS LIST MECHANICAL ABBREVIATIONS A.F.F. ABOVE FINISHED FLOOR E.A. EXHAUST AIR R.A. RETURN AIR CFM CUBIC FOOT OF AIR O.A. OUTSIDE AIR S.A. SUPPLY AIR PER MINUTE l� 1 RAASCH ASSOCIATES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 tr PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E —MAIL: engineer @raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES MECHANICAL SYMBOLS Winne Count 4 770r` �ifia. tI�.Tatr°'tdr�� SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT ACCESS DOOR O PLUG VALVE larb DUCT C— ELBOW FITTING (TURNED DOWN) o ELBOW ��dx RETURN DUCTWORK (TURNED UP) (FIRST FIG. IS TOP) TEE OUTLET UP ® SUPPLY DUCTWORK ^ TEE OUTLET DOWN DUCT LINING REDUCER (CONCENTRIC) MOTORIZED DAMPER REDUCER (ECCENTRIC) MANUAL VOLUME DAMPER 7 CAP M FLEXIBLE DUCT I I UNION SD SMOKE DETECTOR FIRE DAMPER FD 9 PRESSURE GAUGE LSD SMOKE DAMPER THERMOMETER � MANUAL VOLUME DAMPER OT THERMOSTAT O SENSOR —G— GAS (NATURAL) MECHANICAL ABBREVIATIONS A.F.F. ABOVE FINISHED FLOOR E.A. EXHAUST AIR R.A. RETURN AIR CFM CUBIC FOOT OF AIR O.A. OUTSIDE AIR S.A. SUPPLY AIR PER MINUTE l� 1 RAASCH ASSOCIATES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 tr PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E —MAIL: engineer @raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) Winne Count 4 770r` �ifia. tI�.Tatr°'tdr�� SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDNG A 07/22/10 ISSUED FOR REVIEW MARK DATE DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226- G001.dwg DRAWN BY: R. DIEDERICH DESIGNED BY: M. BACHMANN Copyright © 2010, Roasch Associates, Inc. SHEET TITLE: TITLE SHEET SHEET: G001 I I I ROAD IAN — s� =� =A =AN AIN N IAN sue � � =A — IAN sAN =AN IAN —IAN s =AN =A — _ — _� _ � s� sAN =AN IA — =� — s <� sA� r� 3 pql RTU -5 m m 1 m RTU -4 �i- �9a N ® RTU -1 ® RTU -2 ® RTU -3 11' -5" I 11' -5" 11' -5" I RTU -6 RTU -7 ROOF PLAN NOTES: 1. PERMANENT LADDER. 2. CATWALK TO AND AROUND UNITS. ACCESS TO ROOF VIA EXTENSION LADDERS. TYPICAL OF ALL UNITS. 3. METAL ROOF WALKWAY: A. R & S MANUFACTURING AND SALES CO. INC. B. 24" WIDE C. 18 GAUGE, GALVANIZED STEEL D. SUPPORT PL. SPACING AT 5-0" O.C. FOR PARALLEL RUNS E. ALL FASTENERS CONNECT AT T/ ROOF RIDGE ROOF PLAN llU Sc ALE: 1/16" = 1' -0" i c :L T - 21' -7 1/2" RTU -11 m m 21' -7 1/2" RTU -12 m RTU 14 ��� RTU -13 m 48' -3" 11' -10" 9' -0" i i_ RAASCH ASSOCIATES, WC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E -MAIL: engineer @raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) i s Winnebago t SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A j 07/22/10 j ISSUED FOR REVIEW MARKI DATE I DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226- A101.dwg DRAWN BY: R. DIEDERICH DESIGNED BY: M. BACHMANN Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: ROOF PLAN SHEET: 10 " 1 ROAD —sIN IAN - =AN =AN =AN SAN REMODELING PLAN FOR WEST WING ON SHEET M101 =AN —sue s� \ _� — s� _� s� =A� SAN IAN S IAN III IAN t =A _- _ — =A 5� _ -AN — SAN — s -„ s - — 3 � rr i l N i l i h r�_ I SISTI-E T Os 5 Os a 5 I ' RT - I EF \ T O T RTU -1A RTU -2A RTU -3A T Q T 5 I I I I ® I � 7 7 li I II I I I O I � I I I i Osr I T I C, I i I i I �a II i 7 osTO 7 i T E�� II i -- - _ - - _ - _ - - - - - -_'�I i O I \ i o \ ®0 i \ I T I i C T I I I Ir REMODELING K FOR MAIN HALL SHEET M102 HVAC DEMOLITION PLAN NOTES: 1. REMOVE ROOF —TOP UNIT, CURB AND DUCT CONNECTIONS AT UNIT. DISCONNECT GAS PIPING FROM UNIT. 2. REMOVE CEILING TILES AND SUPPORT TEES BELOW UNITS. STORE AND REUSE WHEN MECHANICAL AND ELECTRICAL WORK IS COMPLETED. 3. REMOVE TEMPERATURE SENSORS AND WIRING. 4. REMOVE THERMOSTATS AND MOUNTING BOARD. 5. REMOVE THERMOSTATS AND WIRING. 6. REUSE SUPPLY DIFFUSERS AND RETURN GRILLES. 7. REMOVE CEILING FANS. REMODELING PLAN FOR SOUTH WING ON SHEET M101 ----------------- 1 i i i i i I RTU -2 i <' � I �O I \ RTU -3 S\ <v /Oi I RTU -4 S <�3 i v I I RTU -5 7 I � I 7 I S' , v I O I i o I I GAS METER O R EF =11 I S O O I 1 — — — — — — — — — — — — — — 320\ R 4 — c/16, VAC DEMOLITION PLAN = 1' -0" I L-L I I I I I I I I I I I I I I I I I I I I I I I I I e RAASCH ASSOCIATES, WC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E—MAIL: engineer @raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) Winnebago t SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A 07/22/10 ISSUED FOR REVIEW MARKI DATE I DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226- M001.dwg DRAWN BY: R. DIEDERICH DESIGNED BY: M. BACHMANN Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: HVAC DEMOLITION PLAN SHEET: m o (T) EF TOILETS TOILETS 18 120 CORRIDOR i 121 VESTIBULE 117 i O 12 "0 v C SO LI I II 12 "0 2 52X12 22 "0 RTU -1 °O F DO � I - HVAC PLAN NOTES: 1. INSTALL ROOF -TOP UNITS WITH CURBS. CONNECT DUCTWORK FROM UNITS TO EXISTING DUCTS IN SPACE. REFER TO CURB DETAIL ON SHEET 1 -M601. REFER TO CONDENSATE PIPING DETAIL 2 -M601. 2. SENSORS FOR DDC CONTROL SYSTEM. 3. EXISTING PACKAGED TERMINAL AIR CONDITIONING UNITS TO REMAIN. 4. EXISTING GAS PIPING ON ROOF. 5. TEMPERATURE MONITORING SENSORS. 6. CONNECT EXISTING GAS PIPING ON ROOF TO UNITS. REFER TO DETAIL 3 -M601. KUUM 108 MEETING ROOM RTU -13 RTU -14 = SG (6) r 6 'I' 6 4 500 L �� i r RG L o 960 S F 1 24X14 38X12 024X14 38X12 RG 0 960 CORRIDOR CI 4 ) -f O - ( 4 ) 110 MEETING 240 � 240 ROOM 107 O O L tTLL--L-IF If 52X12 6 CD 101 3700 100 _ f VESTIBULE O O AD -2 100 O � 0 O CHAIR AD L STORAGE CD f 250 (2) O 40X14 0 1 OS S 1 RTU -15 OFFICE CD STORAGE 100 F E T E ] T T 02 T T O SOUTH WING HVAC PLAN n SCALE: 1/8" = 1' -0" RAASCH ASSOCIATES, WC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E—MAIL: engineer @raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) -�- Ir - -- F� I I I I E-J- I I O I I KUUM 108 MEETING ROOM RTU -13 RTU -14 = SG (6) r 6 'I' 6 4 500 L �� i r RG L o 960 S F 1 24X14 38X12 024X14 38X12 RG 0 960 CORRIDOR CI 4 ) -f O - ( 4 ) 110 MEETING 240 � 240 ROOM 107 O O L tTLL--L-IF If 52X12 6 CD 101 3700 100 _ f VESTIBULE O O AD -2 100 O � 0 O CHAIR AD L STORAGE CD f 250 (2) O 40X14 0 1 OS S 1 RTU -15 OFFICE CD STORAGE 100 F E T E ] T T 02 T T O SOUTH WING HVAC PLAN n SCALE: 1/8" = 1' -0" RAASCH ASSOCIATES, WC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E—MAIL: engineer @raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) f 7 i nF ebag F fn n it' ,. SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A 07/22/10 ISSUED FOR REVIEW MARK DATE DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226- M101.dwg DRAWN BY: R. DIEDERICH DESIGNED BY: M. BACHMANN Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: WEST AND SOUTH WING HVAC PLANS SHEET: M11 WEST WING HVAC PLAN IlU SCALE: 1/8" = 1' -0" MEETING ROOM 109 CHAIR RTU -4 O 7 STORAGE V STIBULE _ _ _ STORAGE 114 113 O 112 I 5 O O 0 RTU -5 1 r PROFESSIONAL SEAL(S) RTU -6 i s f 7 i nF ebag F fn n it' ,. SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT S F-10 CID - HVAC PLAN NOTES: 1. INSTALL ROOF -TOP UNITS WITH CURBS. CONNECT DUCTWORK FROM UNITS TO EXISTING DUCTS IN SPACE. REFER TO CURB DETAIL ON SHEET M601. STENCIL ROOF -TOP UNIT NUMBER ON BOTTOM OF RETURN DUCTWORK. 2. SENSORS FOR DOC CONTROL SYSTEM. 3. EXISTING PACKAGED TERMINAL AIR CONDITIONING UNITS TO REMAIN. 4. TEMPERATURE CONTROL PANEL. 5. TEMPERATURE MONITORING SENSORS. 6. REROUTE GAS PIPING TO MISS NEW RTU LOCATIONS. 7. CONNECT EXISTING GAS PIPING THROUGH ROOF TO UNITS. STENCIL EXISTING GAS PIPING INSIDE BUILDING. 8. CONNECT NEW GAS PIPING TO EXISTING. 9. EXISTING GAS PIPING ON ROOF. 10. CONNECT NEW DUCTWORK TO EXISTING. REUSE CEILING DIFFUSERS. PAINT TO MATCH. 11. EXISTING GAS PIPING INTO BUILDING. 12. TRANSITION BELOW BEAM. v ® SF-8 SF- EXPOSITION AREA 115 CD 6 (10) 50 SF -12 SF -11 6 5� (10) 5 �� MAIN HALL HVAC PLAN SCALE: 1/9' = 1' -0" O T�Z 1 \ C " SF -13 y a� O RTU -8 SF -i6 50 (10) s CD 715 (7) y a. O RTU -9 1 GAS METER 1 4- I J I I I R TU O1 32 ° 0 VESTIBULE 125 RAASCH ASSOCIATES, WC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E-MAIL: engineer @raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) i s f 7 i nF ebag F fn n it' ,. SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT B 9/16/10 ISSUED FOR BIDDING A 07/22/10 ISSUED FOR REVIEW MARKI DATE I DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226- M102.dwg DRAWN BY: R. DIEDERICH DESIGNED BY: M. BACHMANN Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: MAIN HALL HVAC PLAN SHEET: M1 02 PROVIDE PLUG PROVIDE CLEANOUT FOR MAINTENANCE AT EACH CHANGE OF TYPICAL DIRECTION OR EVERY 30' CELL CAP WITH 1" MASTIC TAPE AND Y" DRAIN LINE SLOPE ROOF CURB LINTEGRAL URETHANE CAULK ALL AROUND CAP FRAME. WITH FLOW 1 /B " /FT - A TO ROOF. CONTINUOUS 2V TRIPLE BEAD MASTIC TAPE AND Y" URETHANE CAULK A A = TOTAL FAN PRESSURE _. + 1 INCH CURB BASE NOTCHED TO FIT OVER ROOF PANEL SEAM. \-- ROOF PANEL SUPPORT CHANNEL mlmm� 14" MINIMUM N _ 1. SECURE CURB BASE AND CELL CAP TO ROOF WITH SCREWS PER CURB MANUFACTURER'S INSTRUCTIONS. ROOF OPENING 2. VERIFY SUPPORT STRUCTURE ON BUILDING. ROOF CURB MOUNTING DETAIL SCALE: NTS MAX. TONS CONDENSATE PIPE SIZE 2 3 4" 5 1 30 1 1 4" 50 1 1 2 CONDENSATE DRAIN TRAP DETAIL SCALE: NTS GAS FIRED HEATING EQUIPMENT UNION GAS SUPPLY PLUG VALVE OR GAS O COCK AS REQ'D NOTE: 6" DIRT LEG SEE PLANS FOR PIPING SIZES GAS PIPING CONNECTION DETAIL SCALE: NTS ROOFTOP UNIT SCHEDULE PROFESSIONAL SEAL(S) AIR FLOW COOLING HEATING ELECTRICAL HORSE VOLT/ TAG MANUFACTURER MODEL FILTERS UNIT WEIGHT REMARKS SUPPLY MIN. OA EXT. S.P. EAT LAT (°Fj MBH MBH INPUT OUTPUT VOLTAGE UNIT SUPPLY EXHAUST COMP. COMP. COND. 56001 CEILING 26,000 (CFM) (CFM) (IN WC) DBM"B DB/WB TOTAL SENS, (MBH) (MBH) 26,000 MCA FAN HP FAN FLA REA KW FAN FLA LEADING EDGE 56001 CEILING RTU -1 CARRIER 48TCED12A 3900 1000 0.62 78.6 57,9/57.0 128,9 B3.3 208 166 460/3 25,1 3 1.3 7.7177 8,9 2 @0.6 2 "DISP 1065 1,2,3 WIT CARRIER 4BTCED09A 3050 830 0.62 78.7/68.0 57.9/57.0 106.2 68.4 165 132 48013 20.1 2 33 6.2/6.3 7.3 2 @0.8 2'DISP 1055 123 RTU-3 CARRIER 48TCED09A 3050 830 0.62 787/08,0 57.9/57..0 1062 08.4 165 132 480/3 20,1 2 3.B 6.216.3 73 2 00.8 2 "DISP 1055 123 RTU4 CARRIER 48TCED17A 5200 1470 0.62 79.0168.3 57.9 /57.0 181.1 1118 272 218 48013 47.9 2 3.1 14.7116.7 15.8 3 @0.9 TDISP 2125 1,2,3 RTU -5 CARRIER 48TCFD20A 6500 1530 0.62 78.2/07.6 57,9157.0 213 139,5 346 277 469/3 49.3 3 3.1 141116.7 16.5 3 @0.9 TDISP 2150 123 RTU6 CARRIER 48TCFD20A 6500 1530 0.62 78.2167.6 57.9/57.0 213 139.5 346 277 400/3 49.3 3 3.1 14.7/16.7 16.5 3 @0.9 2'DISP 2150 1,2,3 RTU -7 CARRIER 48TCFD20A 6500 1530 0.62 782/67.6 57.9/57.0 213 139.5 346 277 480/3 493 3 3.1 14.7116.7 16.5 3 @0.9 2 "DISP 2150 1,2,3 RTU8 CARRIER 4BTGFD20A 6500 1530 0.62 78.2167.6 57.9/57.0 213 139.5 346 277 48013 49.3 3 3.1 14.7116.7 16.5 3 @0.9 2'DISP 2150 123 RTU9 CARRIER 48TCFD20A 6500 1530 0.62 78.1/67.5 57.9/57.0 213 139.5 346 277 48013 49.3 3 3.1 14,711 6,7 16.5 3@0.9 2 "DISP 2150 1,2,3 RTU -10 CARRIER 48TCED17A 5000 1340 0.62 7B.9(68.1 57.9/57.0 170.7 109.5 268 214 48013 47.9 2 3.1 14.71] 6.7 15.8 3 00.9 2'DISP 2125 123 RTU -11 CARRIER 48TCED07A 2000 640 0.62 80.0/68.9 57.9/57.0 75.6 47.1 108 86 480,3 17.3 2 1.0 9.7 5.1 1 @ 0.8 2 "DISP 740 1,2,3 RTU -12 CARRIER 4BTCED07A 2000 640 0.62 80.0168.9 57.9/57.0 75:6 47.1 108 86 48013 17.3 2 1.0 9.7 5.1 1 @0.8 2 740 1,2,3 RTU -13 CARRIER 48TCEA04A 950 310 0.62 80.5/692 57.9/570 36.6 22.7 49 39 400/3 112 0.75 1 5.8 2.5 1 @ 0.0 2 "DISP 560 1,2,3 RTU -14 CARRIER 48TCEA04A 950 310 0.62 80.5169.2 57.9/57.0 366 22.7 49 39 48013 11.2 0.75 1 5.8 2.5 1 @0.8 2'DISP 560 123 RTU -15 CARRIER JL 48TCDD12A 3700 745 0.75 777/67.0 58.1/572 111.4 76.3 171 137 48013 251 3 1.8 7.717.7 8.0 2 @0.8 2 "DISP 1065 1,2,3 Nat-: 1. FURNISH WITH EXHAUST FANIECONOMIZER. 2. PROVIDE GAS PRESSURE REGULATOR RATED FOR 5 PSIG INLET PRESSURE, 14 IN WC OUTLET PRESSURE. 3. PROVIDE PHASE REVERSALjPHASE LOSS PROTECTION MONITOR ON UNIT. FAN SCHEDULE PROFESSIONAL SEAL(S) i s f 7 I+1 7nebag _F fn m tt SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT SPEED HORSE VOLT/ TAG MANUFACTURER MODEL TYPE CFM S. P. (IN) (RPM) POWER PHASE REMARKS SF -1 LEADING EDGE 56001 CEILING 26,000 0.0 260 110 WATTS 120/1 1 SF -2 LEADING EDGE 56001 CEILING 26,000 0.0 260 110 WATTS 120/1 1 SF -3 LEADING EDGE 56001 CEILING 26,000 0.0 260 110 WATTS 12011 1 SF -4 LEADING EDGE 56001 CEILING 26.000 0.0 260 110 WATTS 12011 1 SF -5 LEADING EDGE 56007 CEILING 26,000 0.0 260 110 WATTS 27711 1 SF -6 LEADING EDGE 56007 CEILING 26,000 0.0 200 110 WATTS 27711 1 SF -7 LEADING EDGE 58007 CEILING 26,000 0.0 260 110 WATTS 27711 1 SF -B LEADING EDGE 56007 CEILING 26,000 0.0 260 110 WATTS 277/1 1 SF -9 LEADING EDGE 56007 CEILING 26,000 0.0 260 116 WATTS 27711 1 SF -10 LEADING EDGE 56007 CEILING 26.000 0.0 260 110 WATTS 27711 1 SF 11 LEADING EDGE 56007 CEILING 26,000 0.0 260 110 WATTS 27711 1 SF -12 LEADING EDGE 56007 CEILING 26.000 0.0 260 110 WATTS 277!1 1 SF -13 LEADING EDGE 56007 CEILING 26,000 0.0 260 110 WATTS 27711 1 SF -14 LEADING EDGE 56007 CEILING 20.000 0.0 200 110 WATTS 27711 1 SF -15 LEADING EDGE 56007 CEILING 26,003 0.0 260 116 WATTS 27711 1 SF-16 LEADING EDGE 56007 CEILING 20,000 0.0 260 110 WATTS 277/1 1 SF -17 LEADING EDGE 56007 CEILING 26,000 0.0 260 110 WATTS 27711 1 NOTES 1. CONNECT TO EXISTING CONTROL WIRING. II RAASCH ASSOCWTES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 0 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E-MAIL: engineer @raoschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) i s f 7 I+1 7nebag _F fn m tt SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A 07/22/10 ISSUED FOR REVIEW MARKI DATEI DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226- M601.dwg DRAWN BY: R. DIEDERICH DESIGNED BY: M.BACHMANN Copyright © 2010, Raasch Associates, Inc. SHEET TITLE: HVAC DETAILS AND SCHEDULES SHEET: M601 FROM UTILITIES � - - 480/277V, 3�, - - - PANEL X9 O\ X9 -11 X9 -12 X9 -17 X9 -18 20A 1 BCD 1 BCD 1600A 1 XXX - (2) #12 WITH J 40A 40A J 40A J XXA #12 GND /) (3) #8 WITH (3) #8 WITH 480/277V, 3�, 1600A XXX #10 GND #10 GND #10 GND ° �J 480V MAIN SW8 MAIN SWB -1 -1 MAIN SWB -1 -2 MAIN SWB -2 -1 MAIN SWB -2 -3 MAIN SWB -2 -4 MAIN SWB -2 -5 MAIN SWB -2 -6 MAIN SWB -2 -7 MAIN SWB -2 -8 MAIN SWB -2 -9 MAIN SWB -2 -10 MAIN SWB -2 -11 MAIN SWB -2 -12 MAIN SWB -2 -13 MAIN SWB -2 -14 MAIN SWB -2 -15 MAIN SWB -2 -16 200A 200A 200A 100A IOOA IOOA 100A 100A 100A 100A 100A 100A 100A 100A 100A 100A 100A 200A 200A 200A 100A 100A ECSR FRSR ECSR iRs 0 09/16/10 TiS IiKS iE ISSUED FOR REVIEW MARKI DATE I IPTION PROJECT NO: 3226 CAD FILE: 3226 —E101 DRAWN BY: K. WARRICHAIET CHECKED BY: C. DeWAAL Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: DEMOLITION ONE LINE DIAGRAM SHEET: E 1 1 70A 75A 70A 100A 70A 70A 70A L — — — — — — — — — — SPARE — — J (3) #3/0 WITH (3) #3/0 WITH (3) #2 WITH (3) #2 WITH (3) #2 WITH (3) #XX WITH (3) #4 WITH (2) #XX WITH (3) #4 WITH (3) #XX WITH (3) #4 WITH (2) #XX WITH (3) #4 WITH (3) #6 WITH (3) #4 WITH (3) #4 WITH #4 GND #4 GND #8 GND #8 GND #8 GND #XX GND #8 GND #XX GND #8 GND #XX GND #8 GND #XX GND #8 GND #8 GND #8 GND #8 GND ° L,-J XFMR T7 ° LJ-J XFMR X -4 ° LJ-J XFMR X -3 ° LJ-J XFMR X -2 480/277V 3�1 PANEL X10 PANEL X1, PANEL X6 SECT. 1 X10 -3 X10 -4 X10 -9 X10 -10 X10 -15 O\ 1 BOD � 1 ) 1 � 1 � 1 � i 100A O PANEL X4 RTU -1 (HVAC #1) HOT HEATER WATER RTU -2 (HVAC #2) PANEL X3 RTU -3 (HVAC #3) PANEL X2 RTU -4 (HVAC #4) RTU -5 (HVAC #5) RTU -7 (HVAC #7) RTU -6 (HVAC #6) J 30A 30A 40A J 40A J 40A J PANEL X7 (3) #10 WITH (3) #10 WITH (3) #8 WITH (3) #8 WITH (3) #8 WITH #10 GND #10 GND #10 GND #10 GND #10 GND � - - 480/277V, 3�, - - - PANEL X9 O\ X9 -11 X9 -12 X9 -17 X9 -18 20A 1 BCD 1 BCD 1 BCD 1 XXX - (2) #12 WITH J 40A 40A J 40A J XXA #12 GND /) (3) #8 WITH (3) #8 WITH (3) #8 WITH XXX #10 GND #10 GND #10 GND ° �J 480V TRANSFORMER T8 7 480/277V, 3�, 200A -2 -7 277V T X, -2 -9 277V T X1 -2 -11 277V O) O\ 1 Xl BOC BOC BOC 20A 20A 20A / - (2) #12 WITH (2) #12 WITH (2) #12 WITH #12 GND #12 GND #12 GND PANEL Xi, SECT. 2 7 X1 -2 -13 277V 0 1 BOC /) 20A (2) #12 WITH #12 GND LEGEND EXISTING TO REMAIN FAN 10 CEILING FAN 13' CEILING FAN 16 CEILING FAN 5' CEILING FAN 8 CEILING FAN 11' CEILING FAN 14 CEILING FAN 6' CEILING FAN 9 CEILING FAN 12 CEILING FAN 15 CEILING FAN 7 /// / / /// / / / // /// / / /// / / / /// / /// /// EXISTING HVAC EQUIPMENT TO BE REPLACED AND RENAMED EXISTING DEMOLITION O N E LINE DIAGRAM EQUIPMENT TO BE ELECTRICAL SCALE: NONE l_ 1 1I RMSCH ASSOCIATES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E —MAIL: engineer ®raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) T T I Ane ago Gm SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A 07/22/10 ISSUED FOR REVIEW MARKI DATE I IPTION PROJECT NO: 3226 CAD FILE: 3226 —E101 DRAWN BY: K. WARRICHAIET CHECKED BY: C. DeWAAL Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: DEMOLITION ONE LINE DIAGRAM SHEET: E 1 1 _j ROAD >- - - - --< - - - -- �. S) R —1 RTU -2 y '(HVAC #1) (HVAC #2) N OTE 2) � 2 ,.(NOTE 2) CEILING CEI ING `r FAN 2 FAN 4 CEILING `7' FAN 7 T RTU -1A R1U -2A RTU -3A RTU -3 (NOTE 2) (NOTE 2) (NOTE 2) S /,(HVAC #3) 3,NOTE 2) • Sl CEILING 'FAN 10 RTU -4 CEI ING CEILING FAN 6 CEILING � ) (NOTE 2) FAN FAN CEILING lo FAN 13 RTU -5 'FAN 9 CEILING 5) CEILING (NOTE 2 ) 'FAN 5 CEILING FAN 16 J RTU -6 CEILING S �(HVAC #6) CEILING FAN 12 ` J •(NOTE 2) 'FAN 8 7 CEILING CEILING 'FAN 15 FAN 11 • "32 10 EILING FAN 17 0 Q CEILING FAN 14 S. y RTU -7 (HVAC #7) (NOTE 2) V I I I RTU -4A T (NOTE 2) — --- - - - - -- F - - - - -- I I II Q�12 RTU -5A T (NOTE 2) 1 .1 I y: I • NOTES: I RTU -8A RTU -7A T 1. EQUIPMENT SHOWN IN APPROXIMATE LOCATIONS. (NOTE 2) (NOTE 1 2 ELECTRICAL CONTRACTOR SHALL VERIFY EXACT T W LOCATIONS BEFORE BIDDING. 2. EQUIPMENT LOCATED ON ROOF. 3. ALL HVAC EQUIPMENT SHOWN IS SCHEDULED TO `13j' BE REPLACED AND RENAMED IN APPROXIMATELY THE SAME LOCATIONS AS EXISTING. TU -6A NOTE 2) ELECTRICAL DEMOLITION PLAN SCALE: 1116'=1' -0" I.V - - RMSCH ASSOCIATES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E —MAIL: engineer ®raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) 1 p Winnebago Gmt 771- Ifla'J.gG SUNNW POSFF0ON CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A 107/22/101 ISSUED FOR REVIEW MARKI DATE I DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226 —E102 DRAWN BY: K. WARRICHAIET CHECKED BY: C. DeWAAL Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: ELECTRICAL DEMOLITION PLAN SHEET: E 10 2 FROM UTILITIES o I 1600A 7 MAIN SWB -1 -1 200A 200A (3) #3/0 WITH #4 GND PANEL X1, SECT. 1 FP 480/277V, 3�, 1600A SIN SWB -1 -2 MAIN SWB -2 -1 MAIN SWB -2 -3 200A 200A 100A 200A 200A 100A (3) #2 WITH (3) #3/0 WITH #8 GND (3) #2 WITH #4 GND #8 GND 480/277V, 3�, X10 -3 X10 -4 ;6 / B / B 15A 15A (3) #10 WITH (3) #10 WITH #10 GND #10 GND 30A 30A (3) #12 WITH (3) #12 WITH #12 GND #12 GND BOO 30A - (3) #8 WITH #10 GND 30A -(3) #12 WITH #12 GND MAIN SWB 30A f30A L -(3) #12 WITH (3) #12 WITH #12 GND #12 GND 480/277V, 3A PANEL X9 X9 -11 X9 -12 X9 -17 X9 -18 BOO BOO BOO XXX J 30A 25A J 25A J XXA (3) #8 WITH (3) #8 WI130A (3) #8 WITH XXX #10 GND #10 GND #10 GND 480V ° TRANSFORMER T8 -E7 208/120V 3OA 30A (3) #10 WITH (3) #10 W(3) #10 WITH #10 GND #10 GND #10 GND PANEL X8, PANEL X8, SECT. 1 SECT. 2 (2) #12 WITH #12 GND F - 1 IN SWB -2 -1 100A LP 60A J -(3) #4 WITH #8 GND 60A - (3) #6 WITH #8 GND MAIN SWB -2 -4 IMAIN SWB -2 -5 (MAIN SWB -2 -6 (MAIN SWB -2 -7 MAIN SWB -2 -8 MAIN SWB -2 -9 MAIN SWB -2 -10 MAIN SWB -2 -11 MAIN SWB -2 -12 I MAIN SWB -2 -13 I MAIN SWB -2 -14 MAIN SWB -2 -1 100A 100A 100A 100A 100A 100A 100A 100A 100A IOOA 100A 100A O BOCH 100A 20A LPS -RK LPS -RK LPS -RK LPS -RK LPS -RK LPS -RK 60A 60A 60A 60A 60A 60A (2) #12 WITH (2) #12 WITH (2) #12 WITH #12 GND SPARE #12 GND (3) #2 WITH (3) #XX WITH (2) #XX WITH (3) #XX WITH < (2) #XX WITH (3) #6 WITH (3) #4 WITH #8 GND #XX GND (3) #4 WITH #XX GND (3) #4 WITH #XX GND (3) #4 WITH #XX GND (3) #4 WITH #8 GND #8 GND NEW ELECTRICAL EQUIPMENT #8 GND #8 GN D ° J #8 GN D ° J #8 GND INSTALLATION O N E LINE D I A G R A M ° XFMR T7 ° XFMR X -4 SF -6 SF -9 SF -12 SF -15 XFMR X -3 s XFMR X -2 SCALE: NONE PANEL X10 0 09/16/10 ISSUED FOR BIDDING A 07/22/10 1 ISSUED FOR REVIEW MARKI DATE I DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226 —E201 6OA 60A 6OA 60A 60A 60A X10 -15 (3) #6 WITH (3) #6 WITH (3) #6 WITH (3) #6 WITH 3 6 WITH BOO #8 GND #8 GND #8 GND #8 GND � �DWITH #8 GND 20A -(3) #8 WITH 100A HOT WATER O PANEL X4 RTU -4 HEATER RTU -5 PANEL X3 RTU -6 PANEL X2 RTU -7 RTU -8 RTU -10 R #1� PANEL X7 'i 30A f30A L -(3) #12 WITH (3) #12 WITH #12 GND #12 GND 480/277V, 3A PANEL X9 X9 -11 X9 -12 X9 -17 X9 -18 BOO BOO BOO XXX J 30A 25A J 25A J XXA (3) #8 WITH (3) #8 WI130A (3) #8 WITH XXX #10 GND #10 GND #10 GND 480V ° TRANSFORMER T8 -E7 208/120V 3OA 30A (3) #10 WITH (3) #10 W(3) #10 WITH #10 GND #10 GND #10 GND PANEL X8, PANEL X8, SECT. 1 SECT. 2 (2) #12 WITH #12 GND F - 1 IN SWB -2 -1 100A LP 60A J -(3) #4 WITH #8 GND 60A - (3) #6 WITH #8 GND -10 BBD 20A 3) #8 WITH 10 GND l_ 1 - i RAASCH ASSOCIATES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E —MAIL: engineer ®raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES 480/277V, 3�, 200A PANEL X1, SECT. 2 T T I Ane ago Gm X1 -2 -7 277V X1 -2 -9 277V X1 -2 -11 277V X1 -2 -13 277V LEGEND BOCH O� BOCH O) O BOCH O BOCH 20A 20A 20A ) 20A ) EXISTING TO REMAIN (2) #12 WITH (2) #12 WITH (2) #12 WITH (2) #12 WITH #12 GND #12 GND #12 GND #12 GND NEW HVAC EQUIPMENT NEW ELECTRICAL EQUIPMENT INSTALLATION O N E LINE D I A G R A M SF -7 SF -10 SF -13 SF -16 SF -5 SF -8 SF -11 S 1 SF -6 SF -9 SF -12 SF -15 SF -17 < SCALE: NONE -10 BBD 20A 3) #8 WITH 10 GND l_ 1 - i RAASCH ASSOCIATES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E —MAIL: engineer ®raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) T T I Ane ago Gm SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A 07/22/10 1 ISSUED FOR REVIEW MARKI DATE I DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226 —E201 DRAWN BY: K. WARRICHAIET CHECKED BY: C. DeWAAL Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: INSTALLATION ONE LINE DIAGRAM SHEET: E 2 1 ROAD PANEL X9 RTU -5 4 (NOTE 2) I (NOTE 2) PANEL X8, S CT. 1 SF -7 1 1 1 2 3 RTU -6 PANEL X8, SECT. 2 (NOTE 2) °LErs °L s RTU -1 RTU -2 RTU -3 (NOTE 2) I (NOTE 2) I (NOTE 2) I I SF -10 RTU -7 SF -6 0 (NOTE 2) S —1 SF -3 �7 J 1 1 SF -13 RTU -8 SF -9 (NOTE 2) us 7 SF -5 SF -16 E-E TIM J A RTU -9 AREA SF -12 0 (NOTE 2) SF -8 SF -15 SF -11 32 SF -17 V � T ANEL X1, SECT. 1 NEL X1, SECT. 2 CD SF -14 E RTU -10 (NOTE 2)� 10 Flf � P NEL X10 Q rL I I 11 RTU -11 (NOTE 2) — --- - - - - -- F - - - - -- I I 12 NOTES: RTU -12 1. ELECTRICAL EQUIPMENT AND CONDUIT RUNS ARE SHOWN IN APPROXIMATE � (NOTE 2) LOCATIONS AND MAY HAVE TO BE SLIGHTLY ADJUSTED TO AVOID INTERFERENCE. COORDINATE ALL WORK WITH OTHER TRADES AND RESOLVE AREAS OF CONFLICT — — — — _ — — BEFORE COMMENCING WORK. T — — — — — uR L EO' -1 2. EQUIPMENT LOCATED ON ROOF. I 13 I 14 RTU -13 RTU -14 (NOTE 2) (NOTE 2) I 15 TU -15 L (NOTE 2) ELECTRICAL INSTALLATION PLAN IJ\I SCALE: 1/16 " =1' -0" I-V - - RMSCH ASSOCIATES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 PHONE: 920 - 434 -2128 FAX 920 - 434 -2112 E —MAIL: engineer ®raaschassoc.com 0 SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) I S I Winnebago Gmt SUNNW POSFF0ON CENTER H VAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A 07/22/10 ISSUED FOR REVIEW MARKI DATE I DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226 —E202 DRAWN BY: K. WARRICHAIET CHECKED BY: C. DeWAAL Copyright © 2010, Raosch Associates, Inc. SHEET TITLE: ELECTRICAL INSTALLATION PLAN SHEET: E 2 0 2 MOTORS AND SPECIAL OUTLETS SCHEDULE ABBREVIATIONS COMB- COMBINATION STARTER ES- EQUIPMENT SUPPLIER VFD- VARIABLE FREQUENCY DRIVE MAG - MAGNETIC STARTER WU - WITH UNIT HVC - HEATING/ VENTILATING CONTRACTOR MAN - MANUAL STARTER OU - ON UNIT PLGC - PLUMBING CONTRACTOR EC- ELECTRICAL CONTRACTOR NU - NEAR UNIT MC- MECHANICAL CONTRACTOR NO. MOTORS AND SPECIAL OUTLETS HP VOLTS PH KW FLA LOCATION PNL -CKT OCD WIRE (MINIMUM) STARTER NOTES POLE AMP N0. SIZE GND COND TYPE BY 1 RTU -1 (HVAC #1) N/A 480 3 N/A 63.1 ROOF MAIN SWB -2 -6 3 1 70 3 #4 #8 1" N/A N/A 1,2,5 2 RTU -2 (HVAC #2) N/A 480 3 N/A 63.1 ROOF MAIN SWB -2 -8 3 1 75 3 #4 #8 1" N/A N/A 1,2,5 3 RTU -3 (HVAC #3) N/A 480 3 N/A 63.1 ROOF MAIN SWB-2-10 3 70 3 #4 #8 1" N/A N/A 1,2,5 4 RTU -4 (HVAC #4) N/A 480 3 N/A 63.1 ROOF MAIN SWB -2 -12 3 100 3 #4 #B 1" N/A N/A 1,2,5 5 RTU -5 (HVAC #5) N/A 480 3 N/A 63.1 ROOF MAIN SWB -2 -14 3 70 3 #6 #8 1" N/A N/A 1,2,5 6 RTU -6 (HVAC #6) N/A 480 3 N/A 63.1 ROOF MAIN SWB -2 -16 3 70 3 #4 #8 1" N/A N/A 1,2,5 7 RTU -7 (HVAC #7) N/A 480 3 N/A 63.1 ROOF MAIN SWB -2 -15 3 70 3 #4 #B 1" N/A N/A 1,2,5 8 RTU -1A N/A 480 3 N/A 29 ROOF PANELX9 -11 3 40 3 #8 #10 1" N/A N/A 1,2,6 9 RTU -2A N/A 480 3 N/A 29 ROOF PANEL X9-17 3 40 3 #8 #10 1" N/A N/A 1,2,6 10 RTU -3A N/A 480 3 N/A 29 ROOF PANEL X9 -12 3 40 3 #8 #10 1" N/A N/A 1,2,6 11 RTU -4A N/A 480 3 N/A 29 ROOF PANELXIO -10 3 1 40 3 #8 #10 1" N/A N/A 1,2,6 12 RTU -5A N/A 480 3 N/A 29 ROOF PANELX10 -15 3 40 3 #8 #10 1" N/A N/A 1,2,6 13 RTU -6A N/A 480 3 N/A 29 ROOF PANEL X70 -9 3 40 3 #8 #10 1" N/A N/A 1,2,6 14 RTU -7A N/A 480 3 N/A 15 ROOF PANEL X10 -3 3 30 3 #10 #10 1" N/A N/A 1,2,6 15 RTU -BA N/A 480 3 N/A 15 ROOF PANEL X10 -4 3 30 3 #10 #10 1" N/A N/A 1,2,6 16 CEILING FAN -1 N/A 120 1 110W N/A CEILING WEST PANELXB -1 -20 1 20 2 #12 #12 3/4" 1 N/A N/A 3,4 17 CEILING FAN -2 N/A 120 1 110W N/A CEILING WEST PANELXB -1 -20 1 20 2 #12 #12 3/4" N/A N/A 3,4 18 CEILING FAN -3 N/A 120 1 110W N/A CEILING WEST PANELX8 -1 -20 1 20 2 #12 #12 3/4" N/A N/A 3,4 19 CEILING FAN -4 N/A 120 1 110W N/A CEILING WEST PANELXB -1 -20 1 20 2 #12 #12 3/4" N/A N/A 3,4 20 CEILING FAN -5 N/A 277 1 110W N/A CEILING CENTER PANELX7 -2 -9 1 20 2 #12 #12 3/4" N/A N/A 3,4 21 CEILING FAN -6 N/A 277 1 110W N/A CEILING CENTER PANELX1-2-11 1 20 2 #12 #12 3/4" N/A N/A 3,4 22 CEILING FAN -7 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -7 1 20 2 #12 #12 3/4" N/A N/A 3,4 23 CEILING FAN -8 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -9 1 1 20 1 2 #12 1 #12 3/4" N/A N/A 3,4 24 CEILING FAN -9 N/A 277 L 11OW N/A CEILING CENTER PANELX1-2-11 1 20 2 #12 #12 3/4" N/A N/A 3,4 25 CEILING FAN -10 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -7 1 20 2 #12 #12 3/4" N/A N/A 3,4 26 CEILING FAN -11 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -9 1 20 2 #12 #12 3/4" N/A N/A 3,4 27 CEILING FAN -12 N/A 277 1 110W N/A CEILING CENTER PANEL X1 -2 -11 1 20 2 #12 #12 3/4" N/A N/A 3,4 28 CEILING FAN -13 N/A 277 1 110W N/A CEILING CENTER PANELX7 -2 -7 1 20 2 #12 #12 3/4" N/A N/A 3,4 29 CEILING FAN -14 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -9 1 20 2 #12 #12 3/4" N/A N/A 3,4 30 CEILING FAN -15 N/A 277 1 110W N/A CEILING CENTER PANELX1-2-11 1 20 2 #12 #12 3/4" N/A N/A 3,4 31 CEILING FAN -16 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -7 1 20 2 #12 #12 3/4" N/A N/A 3,4 32 CEILING FAN -17 N/A 277 1 11OW N/A CEILING CENTER PANEL X1 -2 -13 1 20 2 #12 #12 3/4" N/A N/A 3,4 NOTES: 1 DISCONNECT WIRES FROM RTU AND LOCAL DISCONNECT. 2 REUSE EXISTING CONDUIT AND WIRES FOR NEW RTU. 3 DISCONNECT WIRES FROM FAN. 4 REUSE CONDUIT AND WIRES FOR NEW FAN. 5 REMOVE FUSES. REFERENCE ELECTRICAL INSTALLATION PLAN 3226 -E102 FOR TYPE AND SIZE FOR REPLACEMENT. 6 REMOVE CIRCUIT BREAKER. REFERENCE ELECTRICAL INSTALLATION PLAN 3226 -E102 FOR TYPE AND SIZE FOR REPLACEMENT. DEMOLITION SCHEDULE SCALE: NONE MOTORS AND SPECIAL OUTLETS SCHEDULE ABBREVIATIONS COMB - COMBINATION STARTER ES- EQUIPMENT SUPPLIER VFD- VARIABLE FREQUENCY DRIVE MAG - MAGNETIC STARTER WU - WITH UNIT HVC- HEATING/ VENTILATING CONTRACTOR MAN - MANUAL STARTER OU - ON UNIT PLGC - PLUMBING CONTRACTOR EC- ELECTRICAL CONTRACTOR NU -NEAR UNIT MC- MECHANICAL CONTRACTOR NO. MOTORS AND SPECIAL OUTLETS HP VOLTS PH KW FLA LOCATION PNL -CKT OCD WIRE (MINIMUM) STARTER NOTES POLE AMP NO. SIZE CND COND TYPE BY 1 RTU -1 N/A 480 3 N/A 25.1 ROOF PANELX9 -11 3 30 3 #8 #10 1" N/A N/A 1,2,3,4,9 2 RTU -2 N/A 480 3 N/A 20.1 ROOF PANELX9 -17 3 25 3 #8 #10 1" N/A N/A 1,2,3,4,10 3 RTU -3 N/A 480 3 N/A 20.1 ROOF PANELX9 -12 3 25 3 #8 #10 1" N/A N/A 1,2,3,4,10 4 RTU -4 N/A 480 3 N/A 47.9 ROOF MAIN SWB -2 -6 3 60 3 #4 #8 1" N/A N/A 1,2,3,4,5 5 RTU -5 N/A 480 3 N/A 49.3 ROOF MAIN SWB -2 -8 3 60 3 #4 #8 1" N/A N/A 1,2,3,4,5 6 RTU -6 N/A 480 3 N/A 49.3 ROOF MAIN SWB -2 -10 3 60 3 #4 #8 1" N/A N/A 1,2,3,4,5 7 RTU -7 N/A 480 3 N/A 49.3 ROOF MAIN SWB -2 -12 3 60 3 #4 #8 1" N/A N/A 1,2,3,4,5 8 RTU -8 N/A 480 3 N/A 49.3 ROOF MAIN SWB -2 -14 3 60 3 #6 #8 1" N/A N/A 1,2,3,4,5 9 RTU -9 N/A 480 3 N/A 49.3 ROOF MAIN SWB -2 -16 3 1 60 3 #4 #8 1" N/A N/A 1,2,3,4,5 10 RTU -10 N/A 480 3 N/A 47.9 ROOF MAIN SWB -2 -15 3 60 3 #4 #8 1" N/A N/A 1,2,3,4,5 11 RTU -11 N/A 480 3 N/A 17.3 ROOF PANELX10 -10 3 20 3 #8 #10 1" N/A N/A 1,2,3,4,7 12 RTU -12 N/A 480 3 N/A 17.3 ROOF PANELX10 -15 3 20 3 #8 #10 1" N/A N/A 1,2,3,4,7 13 RTU -13 N/A 480 3 N/A 11.2 ROOF PANELX1013 3 15 3 #10 #10 V. N/A N/A 1,2,3,4,8 14 RTU -14 N/A 480 3 N/A 11.2 ROOF PANELX10 -4 3 15 3 #10 #10 1" N/A N/A 1,2,3,4,8 15 RTU -15 N/A 480 3 N/A 25.1 ROOF PANELX10 -9 3 30 3 #8 #10 1" N/A N/A 1,2,3,4,9 16 SF -1 N/A 120 1 110W N/A CEILING WEST PANEL X8 -1 -20 1 20 2 #12 #12 3/4" N/A N/A 4,6 17 SF -2 N/A 120 1 110W N/A CEILING WEST PANEL XS-1-20 1 20 2 #12 #12 3/4" N/A N/A 4,6 18 SF -3 N/A 120 1 110W N/A CEILING WEST PANEL X8 -1 -20 1 20 2 #12 #12 3/4" N/A N/A 4,6 19 SF -4 N/A 120 1 110W N/A CEILING WEST PANE[ XS-1-20 1 20 2 #12 #12 3/4" N/A N/A 4,6 20 SF -5 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -9 1 20 2 #12 #12 3/4" N/A N/A 4,6 21 SF -6 N/A 277 1 110W N/A CEILING CENTER PANEL X1 -2 -11 1 20 2 #12 #12 3/4" N/A N/A 4,6 22 SF -7 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -7 1 20 2 #12 #12 3/4" N/A N/A 4,6 23 SF -8 N/A 277 1 110W N/A CEILING CENTER PANELX7 -2 -9 1 20 2 #12 #12 3/4" N/A N/A 4,6 24 SF -9 N/A 277 1 110W N/A CEILING CENTER PANEL X1 -2 -11 1 1 20 2 #12 1 #12 3/4" N/A N/A 4,6 25 SF -10 N/A 277 1 110W N/A CEILING CENTER PANELX7 -2 -7 1 20 2 #12 #12 3/4" N/A N/A 4,6 26 SF -11 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -9 1 20 2 #12 #12 3/4" N/A N/A 4,6 27 SF -12 N/A 277 1 110W N/A CEILING CENTER PANEL X1 -2 -11 1 20 2 #12 #12 3/4" N/A N/A 4,6 28 SF -13 N/A 277 1 110W N/A CEILING CENTER PANELX1 -2 -7 1 20 2 #12 #12 3/4" N/A N/A 4,6 29 SF -14 N/A 277 1 11OW N/A CEILING CENTER PANELX7 -2 -9 1 20 2 #12 #12 3/4" N/A N/A 4,6 30 SF -15 N/A 277 1 110W N/A CEILING CENTER PANELX1-2-11 1 20 2 #12 #12 3/4" N/A N/A 4,6 31 SF -16 N/A 1 277 1 1 1 11OW N/A CEILING CENTER PANELX7 -2 -7 1 20 2 #12 #12 3/4" N/A N/A 4,6 32 SF -17 N/A 277 1 11OW N/A CEILING CENTER PANEL X1 -2 -13 1 20 2 #12 #12 3/4" N/A N/A 4,6 NOTES: 1 PROVIDE AND INSTALL DISCONNECT WITHIN SIGHT OF UNIT. PROVIDE AND INSTALL CONDUIT AND WIRE FROM DISCONNECT TO NEW UNIT. 2 WIRE AND CONDUIT SIZES SHOWN ARE MINIMAL. ALL APPLICABLE NEC DERATING FACTORS SHALL BE APPLIED WHEN MULTIPLE CIRCUITS ARE RUN IN ONE CONDUIT OR WHEN CIRCUIT LENGTHS OR LOADS CAUSE EXCESSIVE VOLTAGE DROPS. 3 SUPPLY AND INSTALL WP, GFCI RECEPTACLE NEAR UNIT. FEED FROM NEAREST RECEPTACLE CIRCUIT. 4 REUSE EXISTING CONDUIT AND WIRE. 5 PROVIDE AND INSTALL BUSSMAN LPS -RK FUSES. 6 REUSE EXISTING CIRCUIT BREAKER AND SPEED CONTROL. 7 PROVIDE AND INSTALL SIEMENS TYPE BQD 20 AMP 14KAIC CIRCUIT BREAKER. 8 PROVIDE AND INSTALL SIEMENS TYPE BQD 15 AMP 14KAIC CIRCUIT BREAKER. 9 PROVIDE AND INSTALL SIEMENS TYPE BQD 30 AMP 14KAIC CIRCUIT BREAKER. 10 PROVIDE AND INSTALL SIEMENS TYPE BOD 25 AMP 14KAIC CIRCUIT BREAKER. NSTALLATION SCHEDULE SCALE: NONE ELECTRICAL SYMBOLS LIST SYMBOL I DESCRIPTION MOUNTING SYMBOL IDESCRIPTION MOUNTING WIRING DEVICES — RECEPTACLES ® DUPLEX RECPT. (WALL, FLOOR, ABOVE COUNTER) OG DUPLEX RECPT. W /GROUND FAULT $Wp DUPLEX RECPT. W/WEATHERPROOF COVER 0TVSS WTVSS DUPLEX RECPT. W /SURGE SUPPRESS. (WALL, FLOOR, A.C.) DOUBLE DUPLEX RECPT. *XXX SPECIAL PURPOSE CONNECTION COMPUTER DUPLEX RECPT. (WALL, FLOOR, ABOVE COUNTER) WELDING OUTLET (3- PHASE, 1- PHASE) WIRING DEVICES — SWITCHES $ $3 ISWITCH (SINGLE -, THREE -WAY) $T TIME SWITCH $0 DIMMER SWITCH ■ OS OCCUPANCY SENSOR POWER EQUIPMENT .!!I PANELBOARD TRANSFORMER ❑' DISCONNECT SWITCH (FUSED, NON- FUSED) 8 POWER METER X ELECTRIC MOTOR ® JUNCTION BOX LIGHT FIXTURES �J FLUORESCENT, HID OR INCANDESCENT (CEILING, WALL) FLUORESCENT TROFFER (CEILING, WALL) ®el ®I EXIT SIGN (SINGLE, DOUBLE FACE - CEILING, WALL) EMERGENCY BATTERY PACK f INDUSTRIAL STRIP COMMUNICATIONS EQUIPMENT © COMPUTER DATA OUTLET ❑T TELEVISION OUTLET TELEPHONE OUTLET Q SPEAKER WITH VOLUME CONTROL 0 SPEAKER ®xD, xV COMBINATION TELEPHONE /COMPUTER DATA OUTLET X = #, D = DATA, V = VOICE FIRE AND SECURITY ALARM DEVICES D4 FIRE ALARM ANNUNCIATOR e MOTION DETECTOR OS OH FIRE DETECTOR (SMOKE, HEAT) ■SW ALARM ACTIVATION SWITCH OS7 ADDRESSABLE IONIZATION SMOKE DETECTOR ❑F FLOW SWITCH OSP ADDRESSABLE PHOTOMETRIC SMOKE DETECTOR ❑® SECURITY CAMERA QSDS OSDR LIEBERT DUCT SMOKE DETECTOR (SUPPLY AND RETURN) 0 09/16/10 SYSTEMS A ❑D DOOR POSITION INDICATOR IC INTERCOM STATION ETH ELECTRIC TRANSFER HINGE C[3 DOORBELL EML ELECTRIC MORTISE LOCK SHEET TITLE: SCHEDULES AND ELECTRICAL SYMBOLS LIST DOORBELL PUSH BUTTON ® WATER DETECTOR TH THERMOSTAT & HUMIDISTAT STATION ® CARD READER QT THERMOSTAT © PULL STATION GS GENERATOR SELECTOR SWITCH MA FM -200 MANUAL ACTIVATE ABORT STATION ELECTRICAL SYMBOLS LIST SCALE: NONE l_ 1 - i RMSCH ASSOCIATES, INC. ENGINEERS ARCHITECTS 400 AMS COURT GREEN BAY, WISCONSIN 54313 O PHONE: 920 - 434 -2128 FAX: 920 - 434 -2112 E -MAIL: engineer ®raaschassoc.com D SERVING INDUSTRY & COMMERCE IN THE UNITED STATES PROFESSIONAL SEAL(S) I Ane ago Gmmt 770' l ^'r7.a.t ti F'�trtr5 SUNNYVIEW EXPOSITION CENTER HVAC REPLACEMENT 0 09/16/10 ISSUED FOR BIDDING A 07/22/10 ISSUED FOR REVIEW MARK DATE DESCRIPTION PROJECT NO: 3226 CAD FILE: 3226 —E301 DRAWN BY: K. WARRICHAIET CHECKED BY: C. DeWAAL Copyright © 2010, Raasch Associates, Inc. SHEET TITLE: SCHEDULES AND ELECTRICAL SYMBOLS LIST SHEET: E 3 1