HomeMy WebLinkAboutElectric - 06/14/1996 CODE ENFORCEMENT DIVISION
DEPARTMENT OF COMMUNITY DEVELOPMENT
OSHKOSH CITY OF OSHKOSH, WISCONSIN
ON THE WATER CORRECTION NOTICE
Issue Date 6/14/96 Compliance Date 7/14/96 Compliance No
Address 353 WINDINI3f3ROOK DR Inspected By John Sullivan
Name Address City State Zip Code
Sent X Owner SAWYER CREEK PROPERTIES Oshkosh WI 54901 -0000
to
P9 Contractor MORRIS ELECTRIC INC. 1037 MITCHELL AVE APPLETON WI 54915
U Other
u Inspector
u Required for Occupancy Occupancy Notice 0 First 0 Second Final O Other
Introduction Wire the whirl pool to the manufacture's instruction.
Item 0 Code Compliance Compliance Date
Description
Summary Please call tor a re Inspection at 236 5046.
DEFICIENCIES MUST BE CORRECTED AND APPROVED BEFORE CONCEALMENT. CALL (414) 236 -5050 FOR INSPECTION.
Signature Date
Page 1 of 1
CORNER SKIRT INSTALLATION
See diagrams for factory skirt installation. IMPORTANT: Use of factory skirts requires the unit to be directly on
the subfloor. The subfloor MUST be the same height as the finished floor. If this is not done, the result will be
unnecessary trimming or possibly a skirt that will not fit. Swirl -way will not be financially responsible for either.
After the installer has decided the exact measurement the panel or skirt should be trimmed, follow procedures
listed below.
TOOLS NEEDED FOR TRIMMING SKIRT:
7 1/4" Circular Saw 7" Abrasive Coated Blade (diamond coated preferred)
Framing Square Tape Measure #2 Pencil
Caution: Do not use permanent marker on skirt or panel.
1. Mark off evenly on both ends the amount of skirt not needed.
2. Always add approximately 1/8" to total measurement.
3. When marking line to be trimmed, be sure that the line is 90 degrees square with the top horizontal detail line of
skirt.
4. Secure skirt on table or get someone to hold the skirt or panel firmly so it does not move.
5. Slowly remove skirt area not needed.
6. Dress rough edges or chipped acrylic using a beltsander, angle grinder or sanding block. (60 grit paper recommended)
*Remember it is always better to allow for mistakes. Mark off extra and sand back to exact lines.
1. Line out all necessary parts and tools needed:
TOOLS NEEDED FOR INSTALLING SKIRT:
(7) #10 1 1/2" flathead screws included with skirt)
Electric or pneumatic drill 1/8" drill bit Phillips head screwdriver
2. Position skirt under the bath lip. Be sure detail breaks on the skirt and bath are aligned. After aligning the skirt,
drill a 1/8" pilot hole through ABS base (holes through the skirt should be pre drilled from factory if skirt is
ordered with bath). Secure skirt to the tub with supplied #10 screws.
3. Align provided toe piece with bottom of skirt and secure with velcro strips (illustration C). Toe piece will cover
exposed portion of screws.
A. B. C.
DETAIL BREAKS BATH BOTTOM view
SKIRT
v LIP
ri N10 SCREW WOODEN SPACER
SKIRT
s� i� l
019 TOE PIECE 0■■■• ABS BASE
SCREW
EX
EXPLODED
VELCRO ADHESIVE STRIP
BASIC ELECTRICAL
1. All whirlpools must be connected to a circuit that is protected by a Ground Fault Circuit
Interrupter. We recommend the GFCI be located at the main breaker panel. DO NOT
LOCATE THE GFCI UNDER THE WHIRLPOOL.
2. All whirlpools come with a double insulated motor and a pre -wired cord and (two prong)
plug. No ground wire is required in the plug because the motor is double insulated.
However, the power supply must be GFCI.
3. Inline heater using an Air Switch on /off switch. See diagram 1 -A. Requires a separate
120 volt, 15 amp GFCI circuit.
4. Inline heater using a Timer on /off switch. See diagram 1 B. Requires a separate 120 volt,
15 amp GFCI circuit.