The URL can be used to link to this page

Home My WebLink About12900 (7/18/07)-Building permit (roof) ~ e OSHKOSH ON THE WATER Issue Date 7/18/2007 Address 1130 N WESTFI ELD ST INSPECTION SERVICES DIVISION ROOM 205 DEPARTMENT OF COMMUNITY DEVELOPMENT CORRECTION NOTICE CITY OF OSHKOSH 215 CHURCH AVE PO Box 1130 OSHKOSH WI 54903-1130 Compliance Date 8/17/2007 IMMEDIATELY Compliance No Sent to ~ Owner Name EVERGREEN MANOR INC Address 1130 N WESTFIELD ST City OSHKOSH State Zip Code WI 54902 -3217 Introduction U Required for Occupancy Occupancy Commercial Reroofing has commenced prior to securing the required Building Permit. The required information shall be provided for review ~nd acceptance to determine compliance with applicable codes prior to permit issuance. Item # Code 7-8 Compliance No Description Reroofing has commenced prior to securing the required Building Permit. Compliance Date 08/17/2007 IMMEDIATELY 07/18/2007 Last Updated Item # 2 Code Comm 62.2603.4 Compliance No Compliance Date 08/17/2007 IMMEDIATELY Description [Provide information demonstrating the foam insulation is separated with a thermal barrier as required by 62.2603.4 or is part of a Tested/Listed Listed Roofing system as described/required by Comm 62.2603.4.1.5. See enclosed code sections for further information. 07/18/2007 Last Updated 12900 Page 1 of 2 e OSHKOSH ON THE WATER Issue Date 7/18/2007 Address 1130 N WESTFIELD ST INSPECTION SERVICES DIVISION ROOM 205 DEPARTMENT OF COMMUNITY DEVELOPMENT CORRECTION NOTICE CITY OF OSHKOSH 215 CHURCH AVE PO Box 1130 OSHKOSH WI 54903-1130 Compliance Date 8/17/2007 IMMEDIATELY Compliance No Sent to ~ Owner Name I EVERGREEN MANOR INC Address 1130 N WESTFIELD ST City OSHKOSH State Zip Code WI 54902 -3217 Introduction U Required for Occupancy Occupancy Commercial Reroofing has commenced prior to securing the required Building Permit. The required information shall be provided for review ~nd acceptance to determine compliance with applicable codes prior to permit issuance. Item # 3 Code Comm 62.1605 Compliance No Compliance Date 08/17/2007 IMMEDIATELY Description Provide information demonstrating the weight of the roofing materials in place do not exceed the capacity of the building design. (what was the weight of the original roof installed and what is the weight of the materials that are in place presently?) 07/18/2007 Last Updated Summary Compliance shall be provided by the date indicated to avoid additional enforcement action. Violations must be corrected and approved within 30 days unless otherwise noted. Call for reinspections prior to concealment and/or occupancy. Upon completing the corrections, the owner/contractor/agent must sign and date at the bottom of this notice and return it to the Inspection Services Division by the Compliance Date of 8/17/2007 Office hours for obtaining permits are Monday through Friday 7:30-8:30 a.m. and 12:30-1 :30 p.m. or by appointment. To schedule inspections please call the Inspection Request line at 236-5128 noting the address, permit number (when applicable), and the nature of what needs to be inspected. Signature Date Inspected by: Allyn Dannhoff 236-5045 adannhoff@cLoshkosh.wLus I hereby certify the violations listed on this report have been corrected in compliance with the applicable codes. Print Name Company Signature Date Also Sent to: ~ Bldg DAN V BINDER CONSTRUCTION 1224 W SOUTH PARK AVE OSHKOSH WI 54902 -0 --- U Elec --- U HVAC --- U Plbg --- U Designer --- ~ Other HILL TOP ROOFING 5276 COUNTY RD II LARSEN WI 54947 -8732 --- U Inspector 12900 Page 2 of2 ..,'." CHAP"rER26 . .:..:.",:..::>::,<:>,'<. . ....;,,~,', "::f~t~~~;~l.~;1~;:_.~: :' SECTION 260f GENERAL 2601.1 Scope. Theseprovisi611s shall govern the maferi'als, de- sign, application, construction and installation oHoarn phl.stic; foam plastic insulation, plastic veneer, interior plastic finish . and trim, and light-transmhtingplastics. See Chapter 14 for re~ quirements for exterior wall finish and trim. SECTION 2602 DEFINITIONS 2602.1 General. The following words and terms shall, for the purposes of this chapter and as used elsewhere in this code, have the meanings shown herein. FOAM PLASTIC INSULAnON. A plastic that is intention- ally expanded by the use ofa foaming agent to produce a re- duced-density plastic containing voids con~isting of open or closed cells distributed throughout the plastic for thermi;ll insu- lating or acoustical purposes and that has a density less than 20 pounds per cubic foot (~20 kg/m3). - LIGHT-DIFFUSING SYSTEM. Construction consisting in whole or in part of lenses, panels, grids or baffles made with light-transmitting plastics positioned below independently mounted electrical light sources, skylights or light-transmitting plastic roof panels. Lenses, panels, grids and baffles that are part of an electrical fixture shall not be ~on~idered asa light -dif- fusing system. LlGHT- TRANSMITTING PLASTIC . ROOF PANELS. Structural plastic panels other than skylights that are fa,stened to structural members, or panels or sheathing and that are used as light-transmitting media inthe plane of the roof. LlGHT- TRANSMITTING PLASTIC WALL PANELS. Plastic materials that are fastened to structural members, or to structural panels or sheathing, and that are used as light-trans- mitting media in exterior walls. PLASTIC, APPROVED. Any thermoplastic, therinosetting or reinforced thermosetting plastic material that conforms to ' combustibility classificationsspecifredin the' section applica- . ble to the application and plastic type. . PLASTIC GLAZING. Plastic materials that are glazecl orset in frame or sash and not held by mechanicalfasteners that pass through the glazing material. REINFORCED PLASTIC, GLASS FffiER. Plastic rein- forced with glass fiber having not less than 20 percent of glass fibers by weight. . . THERMOPLASnC~TERIAL.A-p~astiQ mate~iaiihat is ._" capable of being repeatedly softened by increa~e .of ,tem.pyJ:a- ture and hardened by decrease of temperature. . THERMOSETTING MATERIAL. A plastic material that is capable of being changed into a substantially nonreformable product when cured. 2002 WISCONSIN ENROLLED COMMERCIAL BUILDING CODE SECTION 2603 FOAM PLASTIC'INSULATION 2603.1 General. The provisions of this section shall govem the requirements and uses of foam plastic insulation in buildings and structures. ,. 2603.2 Labeling and identification. Packages and containers of foam plastic insulation and foam plastic insulation compo- nents delivered to the job site shall bear the label of an approved agency showing the manufacturer's name, the product-listing, , product identification and informationsufficientto determine that th d use will comply with the code requirements. rface-buming characteristics. Unless otherwise dicated in this section, foam plastic insulation and foam plas- tic cores of manufactured assYIllbliy~snall h,nTe<tflame spread index ofnotmorethan75 and a smoke-developed index of not more than 450 where tested in the maximum thickness in- tended for use in accordance with ASTM E 84. Loose-fill-type foam plastic insulation' shall be tested as board stock for the flame spread index and smoke-developed index. Exceptions: 1. Smoke-developed index for interior trim as provided for in Section 2604.2. 2. In cold storage buildings, ice plants, food plants, food processing rooms and similar areas, foam. plastic in- sulation where tested in a thickness of 4 iIlches (102 mm) shall be permitted in a thickness up to 10 inches (254 mm) where the building is equipped throughout with an automatic fire sprinkler system in accordance with Section 903.3.1.1. The approved automatic sprinkler system shall be provided in both the room and that part of the building in which the room is h cated. .3. Foam plastic insulation that isa part of a Class A, B or C roof-covering assembly' provided the assembly with the foam plastic insulation satisfactorily passes FM 4450 or UL 1256. The smoke-developed index shall not be limited for roof applications. . 4. Foam plastic insulation greater than 4 inches in thick-' ness shall have a maximum flame spread index of 75 and a smoke-developed indexof 450 where tested ata minimum thickness of 4 inches, provided the end use is approved in accordance with Section 2903.7 using the thickness and density intended for use. 2603.4 Therm~llmrri,~l'" E"c:ept as provided for in Sections 2603.4. band 2603.7, foam plastic shall be separated frOluthe interior of a building by an approved thermal barrier of OS inch .... (12.7 mm) gypsum wallboard or equivalen,ttherill31 barrierma~ terial that will limit the average temperature rise of the unex~ . posed surface to not more than 2500F (120oC) after 15 minutes of fire exposure, complying with the standard time-tempera- ture curve of ASTM E 119. The thermal barrier shall be in- stalled in such a manner that it will remain in place for 15 B-519 2603.4.1 - 2603.4.1.10 minutes based on FM 4880, UL lO400rUL 1715. Combustible concealedspacesshall comply with Section 716. ;"'. ~.,~, ",.! ~"ff~N~;1ii:O:ililUi_ rier specified in Section 2603.4 is not required under the conditions set forth in Sections 2603.4.1.1 through 2603.4.1.12. 2603.4.1.1 Masonry or concrete construction. In a ma- sonry or concrete wall, floor or roof system where the foam plastic insulation is covered on each face by a mini- mUIl) of I-inch (25.4 mm) thickness of masonry or con- crete. ~ttllllls. Foam plastic in- stalled in a maximum thickness of 10 inches (254 mm) in cooler and freezer walls shall: 1. Have a flame spread index of 25 or less and a smoke-developed index of not more than 450, where tested in a minimum 4- inch (102 mm) thick- ness. 2. Have flash ignition and self-ignition temperatures of not less than 6000P and 8000P (3160C and 4270C), respectively. 3. Have a covering of not less than 0.032-inch (0.8 mm) aluminum or corrosion-resistant steel having a base metal thickness not less than 0.0160 inch (004 mm) at any point. 4. Be protected by an automatic sprinkler system. Where the cooler or freezer is within a building, both the cooler or freezer and that part of the build- ing in which it is located shall be sprinklered. 2603.4.1.3 Walk-in coolers. In unsprinklered buildings, foam plastic having a thickness that does not exceed 4 inches (102 mm) and a maximum flame spread of 75 is permitted in walk-in coolers or freezer units where the aggregate floor area does not exceed 400 square feet (37 m2) and the foam plastic is covered by a metal facing not less than 0.032-inch-thick (0.81 mm) aluminum or cor- rosion-resistant steel having a minimum base metal thickness of 0.016 inch (0.41 mm). A thickness of up to 10 inches (254 mm) is permitted where protected by a thermal barrier. 2603.4.1.4 Exterior walIs-one story buildings. Por one-story buildings, foam plastic having a flame spread index of 25 or less, and a smoke-developed index of not more than 450, shall be permitted without thermal barri- ers in or on exterior walls in a thickness not more than 4 inches (102 mm) where the foam plastic is covered by a thickness of not less than 0.032-inch-thick (0.81 mm), aluminum or corrosion-resistant steel having a base metal thickness of 0.0160 inch (0041 mm) and the build- ing is equipped throughout with an automatic sprinkler in accordance with Section 903.3.1.1. oam plastic insulation under a roof assembly or rering that is installed in accordance with the code and the manufacturer's installation instruc- tions shall be separated from the interior of the building by wood structural panel sheathing not less than 0.47 inch (11.9 mm) in thickness bonded with exterior glue, B-520 ( . PLASTIC with edges supported 'by blocking,tbngue-aild-'gr60ve joints or other approved type ofede sli ort '. an equivalent material. 2603.4.1.6 Attics and crawl spaces. Within an attic or crawl space where entry is niadeonly for service ofutilF ties, foam plastic insulation shall be protected against ig- nition by 1.5-inch-thick (38 mm) mineral. fiber insulation, 0.25-inch-thick (6Amm) wopd structwal panel, particleboard or hardboard, O.375~inch (9.5 mm) gypsum wallboard, corrosion-resistant steel having a base metal thickness of 0.0 16 inch .(004 mm), or other ap- proved material installed in such a manner that the foam plastic insulation is not exposed. The protective covering shall be consistent with the requirements for the type of construction. 2603.4.1.7 Doors not required to have a tire protection rating. Where pivoted or side-hinged doors are permit- ted without a fire protection rating, foam plastic insula- tion, having aflame spread inqex of 75 or less and a smoke-developed index of not more than 450, shall be permitted as a core material where the door facing is of metal having a minimum thickness of 0.032-inch (0.8 mm) aluminum or steel having a base metal thickness of not less than 0.016 inch (004 mm) at any point. 2603.4.1.8 Exterior doors in bujldings of Groups R-2 or R-3. In occupancies classified as Groups R-2 or R-3 as applicable in Section 101.2, foam-filled exterior en- trance doors to individual dwelling units that do not re- quire a fire-resistance rating shall be faced with wood or other approved materials. 2603.4.1.9 Garage doors. Where garage doors are per- mitted without a fire resistance rating and foam plastic is . used as a core material, the door facing shall be metal having a minimum thickness ofO.032~inch(0.8 niril) alu- minum or O.OlO-inch (0.25 mm) steelorthefacing shall be minimum 0.125-inch-thick (3.2 mm) \\lood., Garage doors having facings other than those desCJ.ibed. above shall be tested in accordance with, andmeet th,ea9cep~ tance criteria of, ANSI/DASMA 107, Exception: Garage doors using foam plastic insula- tion complying with Section 2603.3 in detached. and attached garages associated with one- and two-family dwellings need not be provided with a thermal barrier. 2603.4.1.10 Siding backer board. P~am pl~stiCins~la:' tion of not more than 2,000 Btu/sq.ft (21~7 MJ/m2) as de- termined by NFPA 259 shall be petniittedasa:siding backer board with a maximum thickness of 0.5 inch (12.7 mm), provided it is separated from the interior of the building by not less than 2 inches (51 mm) of mineral fi- ber insulation or equivalent or where applied as insula- tion with residing over existing wall construction. 2002 WISCONSIN ENROLLED COMMERCIAL BUILDING CODE